Load Banks
Test a power source by providing controlled amounts of load to create conditions found in thier application.
See Also: AC Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks, Resistive Load Banks
-
Product
High Power DC Electronic Load
34000C Series（6KW~24KW）
-
34000C Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
Product
Carbon Pile Load Tester 500 AMP
6034
-
• Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported
-
Product
PXI Solid State MUX, 5 bank, 32 channel
40-680-003
-
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
Artificial Phantom Load with Power Factor
RC-50
-
The RC-50 Artificial Phantom Load has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges. Features: Artificial Load, Light Weight, 50 Amps, 50% Power Factor.
-
Product
DC Electronic Loads
-
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.Both static and fully dynamic DC loads are offered. With dynamic functionality 2 levels of load current can be set. The rise and fall time can then be adjusted together with the time period spent at each level. The load can also be made to follow complex waveforms by tracking an external arbitrary oscillator input.
-
Product
DC Electronic Load
3110 Series（250W~700W）
-
Each 3110 Series stand-alone load has its own control and display panel, CC / CR / CV / CP/ Dynamic modes, also can be controlled intranet via RS232 and USB interface.
-
Product
Programmable Electronic Load
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
UYIGAO DC electronic loads provide you with the flexibility to test a wide range of power sources. Perform both static and dynamic tests to ensure that your devices can handle the steady state and occasional transient loads. The 16-bit voltage, current, and power-measurement systems provide accuracy analysis.
-
Product
Load Cell Measurement Interface
LCIC-1106a
-
Industrial Measurement Systems Ltd.
Any application related to weighing or measuring forces is now available in your PC...Stand-alone microcomputer-based interface card requires no other interfacing accessories. Simply connect th
-
Product
6/12/24 Volt Heavy-Duty Variable Carbon Pile Load Tester
6036B-24
-
• Same features as Model 6036B • PLUS the added value of 24 Volt battery testing capacity• Made in USA of US and Global Components
-
Product
PXI Solid State MUX, 2 bank, 80 channel
40-680-005
-
Based on FET switches, the multiplexers have no wear out mechanism and include fault protection that ensures the multiplexer automatically disconnects when PXI power is not applied. Available configurations for the 40-680 range vary from a single 160 to 1 MUX to a 20-bank, 8 to 1 MUX in a single PXI module.
-
Product
2 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, SMA, DC Block+200Ω Load 2 Ports
GPS212
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
PXI MUX 1 Bank of 64 Channel 2 Pole
40-610-022-1/64/2
-
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
ResMap or DualMap Auto Load Floor Standing
-
Creative Design Engineering, Inc.
*Type: Floor Standing*Wafer load: FOUP LoadPort*Wafer size: 300mm, 8" and 300mmopen cassette with adapter*Mini Environment: yes*Probe Changer: 1,2 or 4 probes*Aligner: yes*Range: 1m/ to 10M/*Accuracy:0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic
-
Product
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Fully Loaded w/ Twin Female Contacts (p/n 610138200)
510143003
-
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Fully Loaded w/ Twin Female Contacts (p/n 610138200)
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Product
Low Voltage High Current DC Electronic Load
N62400 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N62400 series is developed based on NGI's years of experience in testing for fuel cell. It is with high accuracy, high reliability and high cost-effective. N62400 series is with high power density and elegant appearance, which is available for benchtop use or installation in 19 inch cabinet.
-
Product
Analog Control Cable for Electronic Loads
EE105T-xx
-
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
