Pneumatic
being of or for the use of pressurized gases.
-
Product
Test Of Hand Pneumatic Tools
-
The measuring system consists of a test site and a control rack. The test site is equipped with a mounting for the test tool with measuring sensors: vibration, torque and speed, as well as a pneumatic regulator, a filter and a powder type brake clutch. The maximum torque test is performed until the rotation is completely stopped. The screen displays both the directly measured maximum torque and the calculated maximum power of this sample. At the end of the test, the results are presented to the operator on the monitor screen.
-
Product
High Accelerated Life Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Rapid Temperature Cycling: Achieves rates up to 100°C/min for accelerated stress screening hass.- Multi-Axis Vibration: Combines pneumatic (6-DOF) and electrodynamic vibration for multi-stress accelerated life testing halt simulations.- Precision Control: halt process ±0.5°C temperature uniformity and real-time monitoring.- Customizable Profiles: Supports stress levels user-defined stress protocols (step-stress, dwell times).- Durability: Robust construction with corrosion-resistant materials
-
Product
Fluid Power Actuators
-
Rotork's product offering of fluid power actuators encompasses GP, CP and RC200 / RCI200 ranges of scotch-yoke pneumatic actuators, GH (scotch yoke) and RH (rack and pinion) hydraulic actuators, the GO range of gas-over-oil actuators, the HPG range of high-pressure direct-gas actuators and the Skilmatic range of electro-hydraulic actuators.
-
Product
Pneumatic Multipliers
CLS
-
The CLS pneumatic torque multiplier provides precision tightening and loosening of all heavy duty fastening connections. The torque multiplier shuts-off when pre-set torque is achieved. It's a non-impacting and operates at a smooth, continuous rotation, the torque multiplier increases speed and productivity, as it is faster than a hydraulic wrench and is less expensive.
-
Product
Topside Probing In-Circuit Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Product
In-cylinder Linear Position Transducers
-
Our In-cylinder Linear Position Transducers are well suited to hydraulic and pneumatic applications. Many of our In-cylinder Linear Position Transducer have features including; touchless magnetostrictive measuring process, unlimited mechanical life, absolute output voltage or current and many more. See our range of products below, click on the links for more information and data sheets.
-
Product
Torque Sensors
-
To improve your product quality and lower your product loss rate, try Mountz torque sensors. Whether you need laboratory-grade precision to measure hand tool output in inch-ounces or the durability to handle frequent pneumatic tool testing in the foot-pound range, Mountz has the right torque sensor for your application. In-line rotary torque sensors even allow you to directly measure the torque a power tool applies to an actual fastener, giving you the most accurate measurement possible. Designed for ease of use, Mountz torque sensors are plug and play, helping technicians get right to work and minimizing the chance of error.
-
Product
Certifier Flow Analyzers
-
TSI Certifier™ Gas Flow Analyzers are multi-functional pneumatic test systems capable of measuring flow, pressure, temperature, and oxygen concentration. They are ideal for testing ventilators, anesthesia workstations, and any other respiratory medical device that produces flows or pressures.
-
Product
Automatic Opening 60° To The Right For MMI-A/B
B03-00059
-
Bonnet opening 60° right, pneumatic MMI-A/B.
-
Product
Precision Linear Actuators
ECT-Series
-
Thomson's ECT Series of Precision Linear Actuators are our highest performing line of electric cylinder systems. Designed for the most demanding applications, the ECT Series is ideal when powerful performance over a long life cycle is required. With a full complement of drive controls, accessories, options, and mounting types, these systems are adaptable to just about any application environment. As a better choice over hydraulic or pneumatic equivalents, the ECT Series are simpler to install, maintain, and control. This family comes in two different sizes mating our traditional Movotrak T90 and T130 actuators with both AC servo and 3 AC induction motor configurations.
-
Product
MCB Endurance Test Bench
-
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
Product
Pneumatic Test Adapter
-
Pneumatic test adapters from INGUN are particularly suitable for contacting medium-sized electronic assemblies (series testing) and a large number of variants. The test adapters are designed as a replacement kit system, are connected to an existing test system and operated with replacement kits that are specially designed for the electronic assembly to be tested.
-
Product
12 Block Rack Mount Receiver
VGR12-RM1
Receiver
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery – next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250VAC/5Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
Mini Pneumatic, Contact, ITA, Push-in Fitting, for 4 mm OD Tubing
610132111
Pneumatic Contact (ITA)
Primary mating contact 610131111.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
Product
I/P Electro-Pneumatic Signal Converters
TEIP11 / TEIP11-PS
-
Electro-pneumatic signal converters are the link between the control rooms and pneumatic actuators. I/P converters are available with and without booster stage.
-
Product
Conveyor Compatible & Conveyor Compatible
Automator Double Sided
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
Round Cold Trap
MCT12
-
We also offer a standard line of both cold traps and right angle poppet valves. Shown at left is a Bemco PV10 Right Angle Poppet Valve and a Bemco MCT12 Round Cold Trap. The cold traps and poppet valves are all stainless steel except for the pneumatic piston. They are available in ASA flange, Conflat, and weld mounting.
-
Product
Pneumatic, Module, Receiver, 5 Position (3/8" ID)
510104160
Receiver Module
These 5 position pneumatic modules are made with G10 Epoxy glass and can withstand temperatures of 140°C.
-
Product
Optical Fiber Tensile Jig
-
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
Product
24 Block Desktop Receiver
VGR24
Receiver
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
Double-Roller Dynanometer
R 200/2 DIVIDED | VP 430004
-
Maschinenbau Haldenwang GmbH & Co. KG.
The double roller dynamometer R 200/2 DIVIDED with an eddy current brake on each roller set and pneumatic lifting beam is designed to measure the performance of trucks and stands out due to its extremely robust, durable and low-maintenance construction. The R 200/2 ensures highest measuring accuracy due to the power measurement at a constant rpm, speed or tractive force, including the towing power measurement. For tuning and adjustment tasks the load simulation is evaluated graphically. An extension up to a wheel power of 660 kW is optionally possible.
-
Product
Air Actuators
-
Del-Tron's linear air actuators (also referred to as linear actuators) are pneumatically actuated crossed roller slide assemblies controlled by a pair of Airpot air cylinders which provide extremely low friction and stiction characteristics. A light touch or physical obstruction will stop the unit’s movement to prevent damage to delicate and expensive equipment and parts. Low pressure operation is possible. The PNRE series requires less than 10 psi to operate.
-
-
Product
13-Pin Pneumatic Coaxial Bblock | Adapter Side
-
13-pin pneumatic coaxial block, adapter side.
-
Product
Aerospace Systems And Technologies
-
The world's leading aircraft manufacturers and engine makers rely on Parker Aerospace's flight control, hydraulic, fuel-inerting, fluid-conveyance, thermal-management, pneumatic, and lubrication systems and components. Parker's systems and technologies expertise helps move customers' programs forward while increasing productivity and profitability.
-
Product
Automatic Fiber Optic Stripping Machine - FBT-800
-
Shanghai Fibretool Technology Co.,Ltd.
Fibretool offers advanced, field-proven fiber stripping machines for efficient processing of coated, buffered, and jacketed glass fiber.The FBT-800 is a pneumatic fiber stripping machine specifically designed for buffer, coating stripping of optical fiber cables and ribbon fibers. The compact machine strips lengths from 5 up to 35 mm with extremely fast cycle times. Absolute precision, high cost effectiveness, and fast return on investment are the main characteristics of this machine.
-
Product
ME2P-C, Pneumatic Adapter
101505
-
The ME2P pneumatic adapter is the perfect solution for high-volume production where precise and automated handling is required. Thanks to the pneumatic stroke and its optional auto-open function, it enables fatigue-free working with manual operation. For combination with robots, the ME2P can be used fully automatically with auto-open-close function in cordoned-off or secured areas. The ME2P offers an opening angle of 90° and is therefore optimised for robot operation. Universal pin carrier, board carrier and hold-down plate. Can be used with both ME2P and ME2 (with the same board carrier dimensions).
-
Product
Electro Pneumatic Circuit
-
Unitech Scales And Measurements Pvt. Ltd
Electrical control of double acting cylinder by solenoidvalve.
-
Product
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules
610132106
Pneumatic Contact (ITA)
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules.
-
Product
Data Logger
DL6
-
Monitor and troubleshoot HVAC systems, verify energy management systems, or track performance of pneumatically controlled valves with Series DL6 Pressure/Temperature/RH Data Logger.
