Pneumatic
being of or for the use of pressurized gases.
-
Product
Compression Test Machines
-
Infinity Machine International Inc.
Compression Test Machines by Infinity Machine International Inc. - for applications such as: baby carriages and strollers durability tester, compressive strength testing machine, tensile testing machine, extrusion compression test equipment for small consumer electronics, paper bursting/crushing compressive strength testing machine, pneumatic springs compressive strength testing machine durability, and more.
-
Product
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules
610132106
-
Mini Pneumatic, Contact, ITA, Hose Barb for 1/8" [3.2 mm] ID Tubing, Fits Mini Coax/Mini Power modules.
-
Product
Test Adapter / Pneumatic Adapter
-
GPS testing technology offers a wide range of pneumatic adapters. The support with compressed air results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.
-
Product
Pneumatic Hand Pumps
-
AMETEK Sensors, Test & Calibration
Our pneumatic hand pumps generate pressure and vacuum with precision and ease, allowing users to fine-tune the pressure delivered with every stroke. A built-in vent valve and dual pressure output enable safe and simple operation. Five different models are available to produce vacuum to 580 psi / 40 bar. Each pump is available on its own, or in one of our complete ready-to-use pump systems.
-
Product
Proximity sensors
-
Voltage 0...250V DC, 230 V AC Cable length 0.3, 2.5, 5, 7.5, 0.2...10 m Plug connection M8, M12 / female thread M5 Electrical Via reed contact Contactless PNP, NPN Pneumatic.
-
Product
Actuator For EMC Tests
PSE-G-MC
-
Pneumatically operated actuator for operation of throttle on motorcycles and 2/3 wheelers. External set-point of the pedal actuator position via analog voltage to closed-loop pressure regulator in external valve box.
-
Product
Hardness Tester
NB3010 Series
-
Newage Testing Instruments, Inc.
A basic Brinell hardness tester with semi-automatic operation. NB3010 is a cost-effective Brinell tester using deadweights with a pneumatic load system to apply and remove the loads. Operates in most all Brinell scales.
-
Product
ServiceJunior Test-Kit
-
Parker's ServiceJunior diagnostic test kits are ideal to digitally measure pressure and capture min and max fluctuations in any hydraulic or pneumatic system.
-
Product
Aerospace Systems And Technologies
-
The world's leading aircraft manufacturers and engine makers rely on Parker Aerospace's flight control, hydraulic, fuel-inerting, fluid-conveyance, thermal-management, pneumatic, and lubrication systems and components. Parker's systems and technologies expertise helps move customers' programs forward while increasing productivity and profitability.
-
Product
Masks Synthetic Blood Penetration Tester
-
Sataton Instruments Technology CO., Ltd
Medical face masks synthetic blood penetration resistance tester is to evaluate the penetration – splash resistance property of medical face masks by the impact of a small fixed volume of a high-velocity stream of synthetic blood which is projected horizontally. The pneumatically controlled valve will simulate the splatter of blood or other body fluid to disburse at the specimen mask. The tester is suitable to determine the synthetic blood penetration of materials or certain materials used in medical face masks.
-
Product
Fire And Overheat Detectors For Aerospace
-
Airline operators demand fire detectors that are highly reliable - the cost of a turn back due to false fire alarm is enormous. Our pneumatic detectors are highly immune to false alarms and require no scheduled maintenance.
-
Product
Vertical Shock/Bump Tester (Pneumatic)
-
HIACC Engineering & Services Pvt. Ltd.
The pneumatic vertical shock and bump test system features an advanced design with a high degree of performance and automation. The testes is easy to use and have low maintenance requirements.
-
-
Product
HDC Torque Controllers
-
The HDC controllers operates with only the HD-Series automation electric screwdrivers. It is a single tool controller that offers programmable speed, angle, auto reverse and soft start options. The controller provides programmable fastening options for sequence based assembly automation applications. The patented HD-Series hybrid system is the world's first torque control tool using both air and electric power to set and control torque. The HDC precise pneumatic pressure sensor and patented algorithm allow for precision digital torque selection.
-
Product
Basic Pneumatic Trainer
-
Unitech Scales And Measurements Pvt. Ltd
It consists of a basic pneumatics kit components for, FRL unit solenoid valve, cylinder etc. This basic pneumatics kit shall be capable of being used to demonstrate to the design, construction and circuits.
-
Product
Fluid Power Actuators
-
Rotork's product offering of fluid power actuators encompasses GP, CP and RC200 / RCI200 ranges of scotch-yoke pneumatic actuators, GH (scotch yoke) and RH (rack and pinion) hydraulic actuators, the GO range of gas-over-oil actuators, the HPG range of high-pressure direct-gas actuators and the Skilmatic range of electro-hydraulic actuators.
-
Product
Pneumatic Type
-
Concentric Technology Solutions, Inc.
The Pneumatic Operation series of shield boxes provides superior performance for efficient RF isolation test environment for testing mobile, WLAN and other small RF devices. Its pneumatic controls to open and close the lid can be controlled manually or with a remote control for semi-automatic operation.
-
Product
D1 Series
-
With VPC's most compact design, the D1 is compatible with a variety of hybrid I/O modules that include: power, coax, signal, vacuum, pneumatic, and high speed digital. Despite its compact size, the D1 can engage up to 160 signal contacts simultaneously.
-
Product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
Pneumatic Vertical Shock Test System
KRD11 series
-
KRD11 series pneumatic vertical shock test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and bump test, can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests.
-
Product
In-cylinder Linear Position Transducers
-
Our In-cylinder Linear Position Transducers are well suited to hydraulic and pneumatic applications. Many of our In-cylinder Linear Position Transducer have features including; touchless magnetostrictive measuring process, unlimited mechanical life, absolute output voltage or current and many more. See our range of products below, click on the links for more information and data sheets.
-
Product
High Sensitivity Pressure Sensors
-
High sensitivity ICP® pressure sensors are for low pressure measurements requiring excellent resolution and small size. They are used to measure small dynamic hydraulic and pneumatic pressures such as turbulence, noise, sound, and pulsations, especially in adverse environments. They are capable of measuring high-intensity sound pressures from 111 to 210 dB at any static pressure level from full vacuum to 1,000 psi (6,895 kPa).
-
Product
Test System for Circuit Breakers
-
Spitzenberger & Spies GmbH & Co. KG
Thermal testing with long-time currents up to 550 A. Magnetic testing with short-time currents up to 2000 A. Control software. Customer specifically adapted. 4 candidate records with pneumatic adapting.
-
Product
Pumps
-
Use the best hand pumps and pump kits for generating pneumatic, hydraulic, and vacuum pressure during your calibration and testing applications. Our products include hand-operated, hydraulic generators that are suitable for a range of liquids. We also offer high- to low-pressure pneumatic pumps that generate air pressure in various bar/psi outputs. Our precision pumps are manufactured by Fluke, Additel, Ametek and Ralston Instruments
-
Product
Soil Testing Complex
GEOMehanika-M
-
The developed measuring complex for testing soils with "GEOMECHANIKA-M" stamps includes:Control and registration unit: measuring station based on NI cRIO equipment, MIDA overpressure sensor, wireless access point AWK-3131-EU-T, pneumatic system based on pneumatics CamozziLinear motion sensorsWireless Operator Console TestSet of connecting cables
-
Product
Fabric Pneumatic Bursting Tester
TF142C
-
TESTEX Testing Equipment Systems Ltd.
Fabric Pneumatic Bursting Tester, to determine the bursting pressure of fabrics uses pneumatic test method, including knits, woven fabric, non-woven fabric, laminated fabric and other craft-made fabric.A test specimen is clamped over an expansive diaphragm by a circular clamping ring, increasing compressed air pressure is applied to the underside of the diaphragm, causing distension of the fabric until the test specimen bursts, the bursting strength and distension are determined.
-
Product
Mini 4 Block Desktop Receiver
VGR4
-
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250VAC/5Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
Power Assembly Tools
-
In order to keep up with modern production demands, you need tools that are faster, smarter, more accurate, and more powerful than ever before. Mountz answers that demand from the heart of Silicon Valley with a full line of innovative electric and pneumatic power tools and automation systems. With intuitive Mountz tool controllers, complex multi-pass assemblies become simple and your production speed will skyrocket. Quality control and regulatory compliance can be streamlined with real-time error proofing and time stamped documentation. From the simplest repairs to the most technical manufacturing projects and everything in between, Mountz power tools stand out from the crowd.
-
Product
Deadweight Testers
-
AMETEK Sensors, Test & Calibration
We provide the world’s only ball-type deadweight testers, where the ball and weights float on a thin film of air, which is virtually frictionless. This design eliminates the necessity to rotate the weights during testing, and allows the user to concentrate on the instrument itself. Our testers are engineered to offer user-friendly, safe operation, in the field, or in a lab. Both pneumatic and hydraulic testers are available.
-
Product
EMC Actuator for Accelerator Pedal
PSE-G
-
Pneumatically operated actuator for operation of accelerator handle. External set-point of the pedal actuator position via analog voltage to closed-loop pressure regulator in external valve box.
