Push Pull Force
stength necessary to press on and extract.
See Also: Force, Compression, Crimp Force, Pull Force, Pull off Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Pull Out Device
BCL-1
-
This Pull out device BCL-1 is designed and manufactured according to relevant standard requirements of IEC884-1/ GB2099.1-2008 and other electrical accessories standards, Mainly used to test the needed maximum force when the plug pull out from socket and the minimum force when single stage plug pull out from socket, and to inspect whether the socket can withstand the lateral stress imposed by electric plug into the socket. This device is applied to plugs and sockets which rated voltage no more than 250V and rated current no more than 16A.Specifications: • Weights: 36N*1, 5.4N*1, 5N*2, 4N*1, 2.6N*1; • Standard testing plug: each one for Dipolar 10A, tripolar 10A and 16A • Standard test bolt: Each one for 1.5N and 2N • 1 set of clamping device • 1 set of Weights tray • Lateral stress weights 5N*1 • 1 set of lateral stress bar
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
Press Force Load Cell
6000 Series
-
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
Product
Force Balanced Accelerometer
PA-23, PA-23BH, S-230
-
The Geotech Model S-230 is a high resolution, 1-component, force balanced accelerometer capable of meeting the noise and stability requirements of the most demanding seismic studies. It features a very wide frequency response (DC to 90 Hz) and an internal calibration coil. Three S-230 accelerometers are packaged as a borehole 3-component unit (Model PA-23BH) and as a surface 3-component unit (Model PA-23). PA-23BH can be submerged up to 100 m depth.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 305gf
K100-L150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Force Sensor Elements
-
The STL Force Sensing Tension Links are a series of unique force sensors. The Tension Links utilize the internal strain gage process sucessfully and are used in bolts, load pins and flat load cells. The sensing element consists of a strain gage bridge circuit internally installed in a small hole along the longitudinal axis. This unique arrangement provides a most effective means for the protective sealing of the internal electronics while minimizing the adverse effects of extraneous torsion and bending loads.
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
Spring Probe
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
Universal SOIC ZIF (Zero-Insertion-Force) Test Socket
Series 547
-
Universal SOIC Zero Insertion Force Test Socket. Devices with up to 44 pins can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. Accepts SOIC gull-wing and J-lead devices, up to 44 pins on .050 [1.27] lead pitch, body widths from .150 to .600 [3.81 to 15.24].
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 155gf
K100-H080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Force Plate Logger Sensor
NUL-225
-
This module is in fact a weight scale designed for a multi range of purposes. Simply lay a heavy weight on its surface, or activate a forceful pressure against it (like a bouncing ball), and the logger sensor will measure it. But that's not all, once a special set of handles are attached, it can also measure pull pressure rather than just weights and presses.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type A, Ø0.80mm, 305gf
K100-A080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style A, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Force Sensors
-
Is defined as a transducer that converts an input mechanical force into an electrical output signal. Force Sensors are also commonly known as Force Transducers.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type A, Ø0.80mm, 155gf
K100-A080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style A, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Universal ZIF (Zero-Insertion-Force) DIP Test Socket
Series X55X
-
Universal Zero Insertion Force DIP Test Socket. All pin count sockets go into PCB with either .300 or .600 [7.62 to 15.24] centers. Sockets can be soldered into PCBs or plugged into any socket. Socket fits into Aries or any competitive test socket receptacle.
-
Product
Cobra Temperature Forcing System for ATE/SLT Test Applications
31000R
System
Cobra is the most advanced, compact,powerful temperature-forcing system on the market. Cobra is an adaptable solution to the ever-increasing thermal demands of post silicon validation and device characterization.
-
Product
Peel Back Force Tester
PBFT
-
Precisely measure the peel back force of carrier tape to verify your packaging systems are within specification. Results can be printed and stored with the outgoing product.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type G, Ø1.50mm, 305gf
K100-G150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style G, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 305gf
K100-K150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
3-Component Quartz Force Links
261 Series
-
Three-component force links eliminate the preload requirement of 3-component quartz force ring sensors, and offers a convenient, 4-screw hole mounting plate on each side end the sensor. Quartz 3-component force links are constructed by installing a 3-component force ring sensor, under preload, between two mounting plates.
-
Product
Atomic Force Microscope
XE-PTR
-
Park Systems' PTR Series is a fully automatic industrial in-line AFM solution for, but not limited to, automatic Pole Tip Recession measurements on Rowbar-level, individual Slider-level, and HGA-level sliders. With sub-nano scale accuracy, repeatability, and throughput, the PTR Series is the metrology tool of choice for Slider manufacturers to improve their overall production yield.
-
Product
Quartz Charge Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
Product
Force Sensors
-
The Force Sensors segment includes a broad line of load cells and force measurement transducers that are offered as precision sensors for industrial and commercial use. Typical applications for force sensors are in medical devices (such as hospital beds and medication dosing), agricultural equipment (for precision force measurement), and construction machinery (for tipping and overload protection). These sensors use our foil technology products, which serve as sensing elements and components within each unit. Further integration of our load cells technology is also offered as part of our weighing module products, which provide customers with a complete sensor assembly that may be used within a wide variety of digital transducers.
-
Product
Force
-
Force instruments are used to measure, apply, or regulate force accurately to prevent damage, improve performance, and ensure safety.
-
Product
Atomic Force Microscope
NaioAFM
-
The NaioAFM is the ideal atomic force microscope for nanoeducation and basic research on small samples. This all-in-one AFM system provides solid performance and easy handling, with a price tag and footprint that fit anyone and any place.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 230gf
K100-D080230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 230gf
K100-I126230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Force Measurement
-
Imada offers a complete selection of force measurement tools including force gauges, test stands and attachments. The gauges can be used by hand or combined into customized force measurement systems capable of addressing a wide variety of applications and budgets.
-
Product
Snap Button Pull Test Machine
UI-TX01
-
Snap Button Pull Test Machine is used to test pull strength of ornaments on garment, toy, footwear and others including button, bow and etc. Snap button pull test is a must-do test especially for Baby and children’s clothing and shoes. The test aims to use to button snap pull tester with suitable grips to pull the ornament to know if the ornament would be pulled off garment or not. The ornament falling off or broken button may cause infants or children the risk of ingestion. The button pull test methods includes 16CFR1500.51-53, ASTM PS79-96, ASTM F963, EN 71-1，M&S P115A and etc.
-
Product
Atomic Force Microscope
LensAFM
-
The Nanosurf LensAFM is an atomic force microscope that continues where optical microscopes and profilometers reach their resolution limits. It is mounted like a normal objective lens, thus extending the resolution and measuring capabilities of these instruments.
