Thickness Gauges
measure distance between opposite sides of a layer.
-
Product
Strain Gauge Test
-
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
Product
Digital Force Gauges
-
Imada digital force gauges are highly accurate instruments that provide the precise force measurement required in quality testing that determines strength and/or functionality of a part or product. Digital gauges can be used for destructive or non-destructive force measurement applications and check both compression and tension (push or pull) forces. The high sampling rate of Imada digital gauges enables them to capture the peak force of destructive tests which occurs in milliseconds. Imada digital force gauges also feature selectable units: lbf, kgf and N and easy-to-program high/low setpoints for Go/No Go testing.
-
Product
RACING GAUGES
PR-8V
-
Use the Multi-Mode (Echo-Echo mode) feature to measure chassis tubing with or without paint and coatings. Built-in automatic gain control and selectable low, medium, and high gain settings offer the inspector the additional punch power for materials that are hard to penetrate. The variety of calibration options is just one more example of the PR-8V's versatility. Store up to 64 custom setups. Factory setups available for common applications.
-
Product
Mechanical Force Gauges
-
AMETEK Sensors, Test & Calibration
The mechanical force gauges from Chatillon offer high precision compression testing (Push) and tensile testing (Pull) at a low cost on a wide range of testing applications.
-
Product
Thick Film Divider
GBR-391
-
GBR-391 series high-voltage resistive dividers are made in a thick film technology on ceramic substrates (Al2O3 - 96%) with leads for through-hole mounting. Dividers are characterized by very high maximum voltage, and standard voltage division.
-
Product
Digital Pressure Gauges
SCJR1-KIT-EMA
-
Parker's ServiceJunior diagnostic test kits are ideal to digitally measure pressure and capture min and max fluctuations in any hydraulic or pneumatic system.
-
Product
Hazardous Environment Pressure Gauge
CODE-91H-V2
-
The Parker Conflow Code 91 - pressure gauge is a traditional bourdon tube type unit, but designed specially for hazardous environments such as mining and quarrying
-
-
Product
Gauge Type T Thermocouple Wire
W-TW-20
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
-
Product
Ergonomic Force Gauges
-
AMETEK Sensors, Test & Calibration
The ergonomic gauges from Chatillon are ideal for functional capacity evaluations and basic muscle strength measurements where economy and ease-of-use are essential. Simplicity is a key design criterion for these ergonomic gauges.
-
Product
Depth Gauge
-
A depth gauge is an easy-to-use tool for measuring depth, slot width, small section sizes and other applications. Depth indices come in different sizes, depending on the specific application. For more details and professional advice regarding Digital depth gauges, please contact us. Wide variety of sizes and styles available.
-
Product
Digital Height Gauges
-
Digital Height Gauges is a measuring device used to determine the height of objects and mark items. Another option is to measure the height of the object using the bottom.
-
Product
Temperature & Pressure Gauges
-
An instrument or device for measuring the magnitude, amount, or contents of something, typically with a visual display of such information.
-
Product
Force Gauge
-
Tension & compression capability .* 5000 g, wide capacity, highresolution, high accuracy, highrepeatability.* 3 kind display unit, g/oz/Newton.* Separate sensor.* Peak hold ( Max. load ) measurement.* Positive or reverse display direction.* Hand held & stand mounting.* Microprocessor circuit & exclusiveload cell transducer.
-
Product
Ergonomic Force Gauges
DMG Series
-
AMETEK Sensors, Test & Calibration
The DMG ergonomic gauge lets you objectively measure manual muscle strength and functional task requirements for almost any application.
-
-
Product
Digital Gauge Pressure
ZET 7112-I VER.2
-
ZET 7112-I VER.2 digital gauge pressure (open membrane) is used for fast and simple pressure measurements and measured values data transfer in digital format via CAN 2.0 interface. ZET 7112-I VER.2 digital gauge pressure (open membrane) is intended for integration into various technological processes automated control systems. Open membrane type enables pressure meters operation in viscous, pasty and rapidly polymerizing environments.
-
Product
Passive and Active Resistor Trimming for Thick and Thin Film
LRT 2000L
-
*Travel: 6" x 6"*Laser : Fiber Laser Ytterbium 1064 nm*Kerf: 30 to 80 micron Adjustable*Pulse width : 80 nano second*Rap Rate: 1 to 1 million Pulse Per Second*Average Power: 20 watts*Target: Electric crosshair on monitor
-
Product
Gauge Type T Thermocouple Wire
W-TW-30
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Battery Fuel Gauge
-
Global Digital Instruments, LLC
SenDEC Battery Fuel Gauges are designed to accurately monitor the charge capacity of lead acid batteries. SenDEC fuel gauges can be used to monitor DC powered equipment such as fork lifts, golf carts, floor care equipment, and any other battery powered equipment. Three battery discharge profiles are standard, plus custom profiles, and a lockout option.
-
Product
Ergonomic Force Gauges
MSE100 Series
-
AMETEK Sensors, Test & Calibration
The MSE100 ergonomic gauge is a simple-to-use, ergonomically designed mechanical instrument ideal for muscle strength evaluations and job task analysis.
-
Product
High Resolution Wafer Thickness & Thickness Variation Gauge
MX 10x series
-
The MX10x series measure thickness and thickness variation on silicon wafers. It has a resolution of 10 nanometers and can be adapted to different thickness ranges within a few seconds.
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Product
Ultrasonic Thickness Gage
27MG
-
The Olympus 27MG is an affordable ultrasonic thickness gage designed to make accurate, measurements from one side on internally corroded or eroded metal pipes, tanks, and other equipment. It weighs only 12 oz. (340 g) and is ergonomically designed for easy, one-hand operation. Thickness range 0.50 mm to 635 mm (0.020 in. to 25.0 in.) depending on material, transducer, surface conditions, temperature.
-
Product
High Resolution Thickness & Surface Profiler for as-sawn Wafers
MX 70x
-
The MX 70x series measure Thickness, Warp, Waviness, Roughness and are usable for nanotopography.
-
-
Product
Height Gauges
V9
-
The height gauge V9 has been developed for the most demanding users. Laboratories and workshops for whom measuring reliability is determining will fully appreciate its exceptional precision level and its "Swiss Made" finish.
-
Product
High Precision Thick Film Chip Resistors
-
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
Product
Thickness Meter for Phosphor Coating
PM200T
-
PM200T is applicable for the manufacturers of fluorescent lamp. During the procedure of powdering tube, PM200T solves the problem efficiently how to control the phosphor thickness and uniformly of the tube. It becomes the important tool to reach best lumen output and save the phosphor.
