Solar Array
field of panels.
-
Product
Solar Cell Simulation
Setfos
-
Easily calculate the short circuit current, open circuit voltage Voc and fill factor with Setfos. Tweak the layer stack and add light scattering layers for enhanced absorption. Optimize for AM1.5 or specific wavelength bandsElectrical IV curvesCurve fitting & parameter extractionAC simulation and transient experiments like photo-CELIVAdvanced device physics: SRH-recombination, excitons, ... Design anti-reflection coatings or transparent cells
-
Product
Solar Ultraviolet Pyranometers
UVR1-T, UVR1-A, &
-
The Middleton Solar UVR1 series are precision filter radiometers for measuring solar global ultraviolet irradiance. The UVR1-T and UVR1-A are suitable for air pollution monitoring. The UVR1-B is suitable for biological and human erythema (sunburn) monitoring.
-
Product
Solar Monitoring Stations
-
EKO Instruments unique Solar Monitoring Station (SMS) is the primary reference to collect high quality solar irradiance data on-site. The innovative turn-key system provides all fundamental solar radiation and meteorological parameters for PV site evaluation, performance monitoring and cell optimizing.
-
Product
SINE M-7 Sinusoidal Array
-
The Sinusoidal Array SINE M-7 has an image size of 22mm x 30mm which makes it small enough to fit into a standard 35mm projection frame. The gray scale is contained in the outer rows. It is made on 35mm perforated film.The TM-G variations are produced on a wider film (without perforations) and cemented between glass. They are available at each modulation (-35, -60, -80).
-
Product
Solar Simulation
-
Sciencetech solar simulators produce high intensity, uniform illumination on a target area. Typically, high power solar simulators use an ellipsoidal reflector to capture light from an arc lamp source inside the reflector, an arrangement that results in a light pattern with a bright outer region and a dark center. This non-uniformity is un- acceptable in many solar simulator applications and as a result, forces many of our solar simulator competitors to use designs involving diffusers to reduce the non-uniformity. This results in a reduction of intensity and a dis- tortion of the spectrum on the target area.
-
Product
SINE M-5 Sinusoidal Array
-
The Sinusoidal Array SINE M-5 is made on a strip of 70mm film approximately 5.12 inches (130mm) in length.The upper row contains the sinusoidal areas with the spatial frequencies in cycles per mm. All sinusoidal areas are carefully oriented with respect to the others, and the lines at the left end of the array have been added for alignment purposes.
-
Product
Mobile Sound Ranging Array
MSRA
-
In a peer to peer conflict, weapon location radars used for counter battery purposes will be extremely vulnerable.With aerial/satellite based surveillance available for the opponent, radars will be seen. With electronic warfare means being omnipresent, radars will be triangulated and jammed. There is an urgent need for 24/7 persistent surveillance with (preferably) passive sensors. With mobility being the key for survival on the battlefield, rapid re-deployable, or even truly mobile sensor capabilities are required. Therefore, the traditional sheer sound pressure based sound ranging capability becomes obsolete, as the triangular footprint of the sensor nodes is too large to be installed on a manned, or unmanned platform. With the trend towards longer ranges and “shoot and scoot” drills, the concept of capturing the muzzle blast noise becomes questionable, as the speed of sound is too slow to provide timely localizations.
-
Product
Microphone Arrays
-
One of the most important parts of an Acoustic Camera is the microphone array. It determines the spatial distribution of the acoustic microphones and therefore measurement performance of the whole system. In order to achieve the maximum possible performance in any given application, we offer a wide variety of microphone arrays. No matter if the measurement is beamforming, intensity or holography ... we have the right microphone array. For special applications we can design and build custom made microphone arrays according to the requirements of the application.
-
Product
Solar Simulator
XES Series
-
The recent environmental issues have been drawing more attention over the past few years. So "solar simulators" have come into the public eye much more often. They are mainly used for the evaluation of solar cells as well as for other types of tests where sunlight needs to be recreated.The continuous light of xenon lamp, the most faithful reproduction of sunlight, is applied in our highly accurate solar simulator, which has been widely sold across Japan and neighboring countries."SAN-EI" offer a wide range of solar-related optical technologies and can guarantee to satisfy the needs and request of customers.
-
Product
Daystar Solar Meter
DS-05A
-
Daystar's DS-05A solar meter brings 'point and read' simplicity to the measurement of solar irradiance. Just turn the meter on, point the sensor at the sun and obtain a reading in Watts/m2.
-
Product
Solar Connectors & Adapters
-
Our SOLARLOK photovoltaic connectors are designed for easy, quick and reliable DC connections for solar technology. With a precision-engineered design, these help achieve the lowest contact resistance to reduce power losses. Our DC Plug and splice connectors provide reliable connection, reducing up to 80% installation time with Insulation Displacement Contact (IDC) technology. Our grounding connectors enable installers to ground the photovoltaic system and create flexibility at the installation.
-
Product
Solar Power Meter
-
*Selectable from two units: W/㎡ and Btu *Peak value retention function *Data retention function *Measure directly without adjustment *Steadily measure for a long period
-
Product
Infrared Array Sensor
Grid-EYE Evaluation Kit
-
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic Automotive & Industrial Systems has launched this evaluation kit for its Grid-Eye infrared array sensor, which integrates a ”nanopower” Bluetooth Smart module and a microcontroller. The kit is intended for prototyping the Grid-EYE sensor which is a 64 pixel IR camera in a surface mount package measuring 11.6mm x 8mm x 4.3mm, which integrates the MEMS sensor, lens and I2C interface. The integrated Bluetooth module in the evaluation kit, the PAN1740, draws 4.9mA in transmit or receive operating modes, which means it can be powered by coin cell batteries. The IR sensor has 64 thermopile elements in an 8×8 grid format that detect absolute surface temperature without any contact.
-
Product
Column Array Loudspeakers
CAL
-
Designed primarily for vocal reproduction in fixed installations, CAL loudspeakers produce a vertical beam of programmable width and then digitally steer the beam’s pattern up to 30 degrees up or down for best intelligibility.
-
Product
Flash Solar Power Meter
-
OAI’s Flash Solar Power Meter is a versatile measurement tool used for measuring the irradiance (in Suns) from Flash Solar Simulators. Flash Solar Simulators are commonly used in the production of solar panels. Integrated into the solar cell production line, this meter calibrates the flash solar simulator allowing for constant and repeatable irradiance output. By sampling at speeds up to 4000 Hz, the flash pulse temporal profile can be recorded in the meter’s memory and downloaded to a USB 2.0 port on a PC for further analysis.
-
Product
Solar Power Meter
Model K-SPM-11
-
Kusam Electrical Industries Limited
SOLAR METER A device used to measure solar power. When the sun shines brightly, just take the KM-SPM-11 and aim its opening at the sun, and you will see how powerful the sun is. If you want your skin white, you surely cannot do without it!
-
Product
Solar Plants Controllers
-
Differential analog solar controller-Elios Basic for solar heating plants: it compares temperatures of fluids in the collectors and the storage tanks and, when the difference is greater than DeltaT, starts the heat exchange through the pump.
-
Product
Solar Analyzers
-
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
Product
Solar Panel Chamber
-
Specifically designed for the solar industry, these climatic chambers feature specifically designed fixtures to properly measure almost any component related to solar panels including the actual panels, grid-tied photovoltaic inverters, or photovoltaic cells and modules.
-
Product
Solar Reference Cell
-
The Solar Reference Cells consist of a 20 mm x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 mm x 70 mm x 16 mm metal enclosure with a protective quartz window and a temperature sensor. Designed for calibrating the irradiance of solar simulators used for testing solar cells and modules.
-
Product
Solar Power Meter
-
This model is very useful in the warehouses, factories, office buildings, restaurants, schools, library, hospitals, photographic, video, parking garages, museums, art galleries, stadiums, building security and so on.
-
Product
SparkFun IR Array Breakout
55 Degree FOV, MLX90640 (Qwiic)
-
It's time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accuracy of ±1.5°C (best case). To make it even easier to get your infrared image, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Solar Simulator
Unisim
-
TS-Space Systems is the first company to pioneer the use of metal halide sources in solar simulators for photovoltaic testing. The high temporal stability and close spectral match combined with the ability to control the output spectrum via multiple separate wavebands means the Unisim solar simulator is the only solar research tool designed for the accurate measurement of multiple junction devices, including the new generation of four junction devices. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. Using the latest HMI and halogen luminaire technology, the Unisim solar simulator provides a highly stable area of illumination. The simulators also use cutting edge filter technology in order to provide the best spectral match available for AM0 and AM1.5. Further to this, the spectrum can be achieved via two, three or four separate spectral wavebands which allows a high degree of spectral control for research and development. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the instrument designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Solar simulators
-
Solar simulators enable the measurement of (dark and) light IV characteristics and of power and efficiency of photovoltaic An artificial light source is used to create illumination conditions that are similar to those in natural sunlight. International standards hosted by ASTM, IEC and JIS allow to classify the properties of a solar simulator with respect to spatial light uniformity, spectral content of the light and time variation of intensity.
-
Product
Impadence Measurement on Multielectrode Arrays
MEArack
-
Well established in electro-physiological research the standard form factor multielectrode arrays (MEAs) are one of the go-to standards when it comes to impedance measurements on cell cultures.
-
Product
Array Sensors
-
Array sensors use closely spaced beams of light to detect even the slightest differences in gray scale between the target and the background within their field-of-view. They are ideal for edge and diameter detection as well as detecting widths and gaps. SICK’s array sensors offer industry-leading reproducibility, in addition to compact, rugged metal housings for use in highly restricted or harsh environments.
-
Product
Continuous Wave Solar Power Meter
-
The OAI Continuous Wave Solar Power Meter is an essential analytical tool for measuring the irradiance (in Suns) of Continuous Wave Solar Simulators. OAI’s Solar Power Meters feature unique features not found in other Solar Meters. This versatile meter can display a wide variety of cell characteristics that include: cell type, window type, cell size, and temperature measurement device type. The OAI Continuous Wave Solar Power Meter can sample and display a continuous reading or peak reading. The Power Meter connects via USB port for data collection, and includes desktop software. With this small, portable, battery-powered meter, numerous production solar simulators can be tested and compared in a short amount of time, leading to greater production line consistency and throughput.
-
Product
Solar ATE
MS 1534
-
The Inverterless ATE is an automatic test equipment which is used to test the all functional and various test conditions of Inverterless Solar Unit. This ATE shall be a GO/NOGO Tester for Inverterless Solar Unit. All production units can be tested with this ATE for functional testing and clearance. This ATE reduces the man effort for quality checks and detects the failure units. The Inverterless ATE can check the UUT with minimum user interactions. It shall test and generate test report in PDF format for the conducted tests with necessary data. The ATE operates on 230V AC power. The ATE has In-Built AC-DC converter which provides 12V DC for operate the unit. Also it has additional AC-DC converter to simulate solar power to the Inverterless units. The main objective of the ATE is to test the Inverterless S in all possible test scenarios without external test equipments and less user interactions.
-
Product
Eddy Current Array
BRIO
-
BRIO is an advanced, ultra-portable Eddy Current Array (ECA) instrument designed for in-service inspections in aerospace, oil & gas, power generation, and manufacturing industries.
