Vector Signal
See Also: Vector Signal Transceivers
-
Product
PXI Signal Insertion Switch Module
Switch Module
PXI Signal Insertion Switch Modules, also known as fault insertion units (FIUs), provide a set of feedthrough channels, which make the switch transparent to the system when closed. You can open or short these channels to one of two fault buses, allowing you to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI Signal Insertion Switch Module can validate the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs). You can also use the FIU models for hardware-in-the-loop (HIL) applications and electronic reliability tests.
-
Product
RF Signal Generator With 1.5 And 3GHz Models
TGR205x Series
-
150kHz to 3GHz (TGR2053) and 150kHz to 1.5GHz (TGR2051) frequency rangeHigh signal purity, phase noise <-117dBc/Hz (typical) at 1GHz output and 10kHz offsetAmplitude range of -127dBm to +13dBm0.1dBm amplitude setting resolutionInternal or external analogue modulations (AM, FM, PM)Amplitude can be set in dBm, dBμV or in linear Volts.Internal or external digital modulations - ASK, OOK, FSK, 3FSK, 4FSK, GFSK, MSK, GMSK, HMSK & PSK with U01 optionModulation SynchronisationFast amplitude and/or frequency sweeps with comprehensive triggering5ms sweep settling time1ppm frequency accuracy, <1ppm drift in first yearModulation waveform output on the rear panelInternal waveforms include: Sine, Square, Ramp, Triangle, PRBS (various lengths) and user-defined patternSimple operation with the colour touch screenProgrammable via USB, LAN (LXI) and GPIB (optional), SCPI compatibleCompatible with previous Aim-TTi RF generators
-
Product
3 Way GPS / GNSS Signal Splitter IP67 Outdoor, N Type, 1-2 GHz, 50 Ohm, Passive
GPS301
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
One Port Vector Network Analyser
TE3001
-
The TE3001 One Port Vector Network Analyser is built for the professional who understands the calibration process and has a network analysis task to perform. The unit features a larger output signal than the TE3000 for better noise immunity, and is supplied with a 6 piece custom calibration kit to remove the effect of test fixtures and cables. Together, these features make the TE3001 ideal for broadcast and plasma applications that require a length of cable for connection and may be high in noise or interference.
-
Product
Signal and Spectrum Analyzer
FSW
Spectrum Analyzer
The high-performance R&S®FSW signal and spectrum analyzer was developed to meet demanding customer requirements. Offering low phase noise, wide analysis bandwidth and straightforward and intuitive operation, the analyzer makes measurements fast and easy.
-
Product
Chassis - 16x16 Non-Blocking, Full Fan-Out Matrix for 50 ohm Signals from 1 GHx to 2.7 GHz
CXS/16x16-50-MF
Chassis
This Chassis is a 16x16 non-blocking, full fan-out matrix for 50 ohm signals from 1 GHz to 2.7 GHz. The system uses splitters and amplifiers on the input side and switch modules on the output side to form a stubless matrix. Unit comes standard with LAN, GPIB and RS232 control. A keypad manual control is optional.
-
Product
Signal Conditioners
-
Process transmitters isolate, filter amplify, and convert sensor signals to 4-20mA current or 0-10V voltage signals for interfacing with controllers and other instrumentation. Select from 2-wire loop-powered 4-20mA transmitters, 3-wire DC-powered transmitters, or 4-wire AC/DC-powered transmitters. 3-wire and 4-wire models are available as 4-20mA transmitters or voltage transmitters. DIN-rail and field-mount version are available. Configuration is easy with Windows software, push-buttons, switches, or pots for span/zero settings depending on the series.
-
Product
PXIe Multiport Vector Network Analyzer, 1 MHz to 9 GHz
M9485A
Vector Network Analyzer
1 MHz to 9 GHzUp to 12-ports in one chassis, 24-ports in two chassis Various applications - full N-port cal, FOM, Pulse, time-domain, noise figure and gain compression analysis capability Improve accuracy, yield & margins with the best PXI VNA speed, dynamic range, trace noise and stability Improve throughput with fast cycle time: 5 msec at 201 points, 2-port calVarious configuration with standard test set and configurable test set
-
Product
Signal Generators
-
NF‘s function generators have been used in many applications, since NF produced the first Japan-built function generator in 1959.A function generator is general-purpose test equipment used to generate various waveforms and to execute trigger, sweep and gate oscillation.
-
Product
Signal, Module, Receiver, CASS, 210 Position, Discrete Wiring
510113125
Receiver Module
Module, Receiver, Cass, Signal, 210 Position, Discrete Wiring
-
Product
RF Signal Generator
-
AC powered RF signal generator offering lower phase noise and USB control.
-
Product
Signaling Software Solutions
-
Adax has built a reputation for providing customers with network control, signaling, throughput, TDM switching equipment and security solutions with its range of hardware products. This is now complemented by its extensive software product line that supports cellular IoT applications to address connectivity, traffic and security issues faced by the industry as the market continues to grow.
-
Product
Mixed Signal Oscilloscope - 1 GHz, 2 Analog Plus 16 Digital Channels
MSOX3102T
Oscilloscope
1 GHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Signal Processor Board
MS 1532
-
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
Product
Mixed Signal Oscilloscope - 100 MHz, 2 Analog Plus 16 Digital Channels
MSOX3012T
Oscilloscope
100 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Bluetooth Enabled Signal Conditioners I/O Modules
microBlox
-
Acromag's microBlox uB Series I/O modules offer a compact, high-performance solution for interfacing sensors and field devices with data acquisition systems. uB signal conditioning modules are ideal to isolate, filter, convert and amplify a wide variety of signal types for test, measurement and control systems. Just plug uB modules into 4, 8, or 16-channel backpanels in any mix for a high-density analog I/O interface. Channel-to-channel isolation provides optimal noise and surge protection from ground loops, spikes, and high common mode voltages.
-
Product
Suitable For Current Or Voltage Process Signals
SEM1600VI
-
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA
-
Product
Multicore ARM + Digital Signal Processor
SI-AM572xDSP
-
The SI-AM572xDSP from Sheldon Instruments is an ARM plus Digital Signal Processor (DSP) carrier card with PCIe-104 and optional FMC expansion ports that may run Linux and be a C programmable platform intended for low power environments that require intensive computing in a cost sensitive solutio
-
Product
Digital Signal Processing
ITA
Digital signal processing routines can be conducted on raw signal data acquired by GaGe high-speed digitizers either directly on the onboard FPGA of the digitizer card via our eXpert FPGA firmware features or can be optionally conducted on GPU cards receiving real-time streaming of raw signal data acquired by GaGe high-speed digitizers via the PCIe interface.
-
Product
Signal Analysis
STA/LTA Detector
-
The STA/LTA Detector program is a representation of a detector of various events in triaxial or single-component time signals. The software is based on one of the STA/LTA detector types.
-
Product
RF Signal Detector
H-055DRV / 01019
-
The RF Signal Detector / 2G Cellular Phone Detector / Wireless Camera Detector / Bug Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices.
-
Product
Signal, Insert, Receiver, QuadraPaddle, SIM, Pass-Thru, 4 Pos, 1 Slot
510180105
SIM Insert
Signal, Insert, Receiver, QuadraPaddle, SIM, Pass-Thru, 4 Pos, 1 Slot.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 4 Analog Plus 16 Digital Channels
MSOX3034T
Oscilloscope
350 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Signal Module, ITA, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 151 107 And 510 109 316)
510151121
ITA Module
This kit has everything you need to attach a VPC ITA Module to a custom designed PCB. This includes the right angle header (P/N 510 109 316) and the ITA Module (P/N 510 151 107).
-
Product
RTM Sensor Signal Conditioning Board
MS 3631I
-
CPCI Rear IO Sensor Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on LAOA, RAOA, AOSS (2), DCM (3), PCS (3), RSA (5) & ASA (4) and TAT sensor interface. This card shall handle excitation, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
Product
RR Signal Source
-
Behlman’s RR series of Railroad Signal Sources and Frequency Converters are low cost, highly reliable, switch mode units built for Railroad Signaling. The RR series can be supplied with any single or three-phase input and outputs a clean, regulated AC signal at a precise frequency from 25 Hz to 250 Hz. These rugged signal sources are built to support the rigors of operating in the harsh environment of Railroad signaling equipment.
-
Product
Signal , Module, Receiver, QuadraPaddle, iCon Series, 160 Position, for crimp contacts
510160101
Receiver Module
Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
Product
Mixed Signal Oscilloscope - 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014T
Oscilloscope
100 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Mixed Signal Oscilloscopes
-
A Mixed Signal Oscilloscope (MSO) is a combination Logic Analyzer and Oscilloscope. Since all inputs sample simultaneously, it is easy to see the timing relationships of the digital and analog components of your circuit. The extra channels also allow for more complex triggering. All of our MSOs have Oscilloscope triggering, Logic Analyzer triggering, SPI triggering and I2C triggering.
-
Product
4 Way GPS / GNSS Signal Splitter IP67 Outdoor, SMA, 1-2 GHz, 50 Ohm, Passive
GPS411
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
