Multipliers
-
product
Frequency Multipliers
Triplers
*No mechanical tuners*fullband operation*planar design*zero Bias
-
-
product
Pneumatic Multipliers
CLS
The CLS pneumatic torque multiplier provides precision tightening and loosening of all heavy duty fastening connections. The torque multiplier shuts-off when pre-set torque is achieved. It's a non-impacting and operates at a smooth, continuous rotation, the torque multiplier increases speed and productivity, as it is faster than a hydraulic wrench and is less expensive.
-
product
Millimeter-wave and Microwave GaAs Multipliers
Keysight Technologies provides MMIC multipliers ideal for microwave radio, aerospace and defense, and instrumentation applications.
-
product
Active Frequency Multipliers
The frequency multiplier which generates output signal with power greater than or equal to input power
-
product
Frequency Multipliers for Radio Amateurs
First approach is to generate the high frequency directly, at the fundamental, using an oscillatortuned on the desired frequency. Few sensitive issues appears here due to high working frequency as, stability, jitter, phase noise, pulling, pushing, low output power, and cost of the active component to meet the performances
-
product
Frequency Multipliers
RF coaxial frequency multiplier (also referred to as a coaxial frequency doubler) PE8600 from Pasternack has SMA conectors and are 50 Ohm. Our SMA frequency multiplier is manufactured for a minimum frequency input of 1.5 GHz and a maximum frequency input of 5 GHz. This SMA microwave frequency multiplier / doubler output minimum frequency is 3 GHz and output maximum frequency of 10 GHz.
-
product
Frequency Multipliers (WR and D Series)
VDI offers a broad range of millimeter-wave varistor mode, passive frequency multipliers based on planar GaAs Schottky diode technology. Frequency doublers and triplers are used to extend the frequency coverage of microwave and millimeter-wave sources.
-
product
Analog Multipliers & Dividers
An analog multiplier/divider is a device that produces an output voltage or current that is proportional to the product of two or more independent input voltages or currents. In addition to multiplying and dividing, multipliers can perform squaring, square-rooting and modulation functions. Applications include radar, communications, and industrial controls where a real-time response is required. Analog Devices’ offers the widest selection of multipliers and dividers.
-
product
Fullband Multipliers
RPG offers a new series of high efficient varactor multipliers based on the newest European GaAs Schottky diode technology. High efficiency and outputpower are one of the key features.
-
product
Pneumatic Radial Gearing Multipliers
RCL
Radial gearing electric torque multipliers are designed for precision tightening and loosening of all heavy duty fastening applications. These multipliers are specially designed for heat plate exchanger applications. The torque multiplier shuts-off when the pre-set torque is achieved. It is non-impacting and operates at a smooth, continuous rotation.
-
product
Components - Passive Multipliers (FT)
FT Series
Farran Technology manufactures a series of standard frequency multipliers which are available in fixed or tunable versions. GaAs Schottky barrier varactors are used to achieve the highest efficiency. The multipliers can be used with solid state or vacuum tube sources. A rugged compact mechanical design is used to maximise reliability.
-
-
product
Step Recovery Diodes
Macom Technology Solutions Holdings Inc.
MACOM’s Silicon and GaAs varactor multiplier diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for multiplier circuits and are available in die form, plastic and ceramic packaging. These diodes boast a flip chip series for higher frequency millimeter wave applications; plastic packaged series for microwave frequency surface mount applications; ceramic packaged series for high power waveguide and coaxial applications.
-
product
Network Synchronization Device
VCH-003
The Network Synchronization Device (NCD) VCH-003 is intended for use on the Unified Telecommunication Network of the Russian Federation. Depending on the configuration of the NSS, VCH-003 can be used to generate and multiply synchronization signals of 2048 kHz and 2048 kbps as part of the PEG, as an OIG to restore synchronization signals received from the line at the transit node.
-
product
Electron Multipliers
Electron multipliers are mainly used as positive/negative ion detectors. They are also useful for detecting and measuring vacuum UV rays and soft X-rays. Hamamatsu electron multipliers have a high gain (multiplication factor) yet low dark current, allowingoperation in photon counting mode to detect and measure extremely small incoming particles and their energy. This means our Hamamatsu electron multipliers are ideal for electron spectroscopy and vacuum UV spectroscopy such as ESCA (electron spectroscopy for chemical analysis) and Auger electron spectroscopy as well as mass spectroscopy and field-ion microscopy.
-
product
Passive Frequency Multipliers
The frequency multiplier which generates output with power level less than input power.
-
product
Get Flexible, Get FlexiFLASH
LatticeXP2
*Up to 885 Kbits sysMEM™ embedded block RAM and up to 83 Kbits distributed RAM*sysCLOCK™ PLLs up to four analog PLLs per device that enable clock multiply, divide and phase shifting*Three to eight sysDSP blocks for high performance multiply and accumulate.*Pre-engineered source synchronous IOs for DDR/DDR2 up to 200 MHz and 7:1 LVDS interface support up to 600 Mbps*Available in csBGA, TQFP, PQFP and BGA packaging
-
product
Frequency Multipliers
Excellent suppression of undesired harmonics and spuriousLow multiplier lossRugged coaxial and surface mount packages
-
product
Smallest Multimetric Nanoparticle Detector
partector 2
Naneos Particle Solutions gmbh
The naneos partector 2 is the world's smallest multimetric nanoparticle detector. The partector 2 uses dual non-contact detection stages to measure not only lung-deposited surface area like the partector 2 Light, but also particle number concentration and average particle diameter. Additionally, ultrafine particle (UFP) surface and ultrafine particle mass concentrations are calculated and displayed. In contrast to some of our competitors, the UFP mass is displayed online, and it is calculated using the measured diameter of the particles, rather than estimated by a simple multiplier for LDSA.
-
product
Attenuation 1000 High Voltage Passive Probe
* high voltage multimeter probe is a 1000:1 fixed attenuation ratio passive probe. This probe is designed to test high voltages for multimeters. With high voltage and high precision.* The test signal can be read on the multimeter, and the multimeter multiplied by 1000 is the actual test result.* High reliability and high security.* The highest voltage can measure DC up to 30KV.
-
product
Hand Multiplexers
MTM
The manual torque multiplier is a low cost solution that's ideal for wheel nuts and remote locations where air and electricity aren’t easily accessible. The gearing design allows for a high torque output with minimal input. Commonly used in petrochemical, power generation, transportation, shipping and maintenance industries.
-
product
Advanced Throughput Multiplier Feature, GTE 10.00p
K8215B
The Advanced Throughput Multiplier feature allows you to test up to two 1000 to 2000 node (between 1296 and 2592 nodes) boards simultaneously on a 4 module tester, thus dividing the test time by half.
-
product
SH-Fm Shunt Resistors
SH-Fm
The interchangeable shunts are used to multiply the measuring range of current of measuring instruments.
-
product
VDI Millimeter-Wave Frequency Extension Modules for PXA, MXA, EXA Signal Analyzers
These modules offer low conversion loss and excellent noise figure. Standard features include dual operating modes. First, the module can function as a high performance down-converting mixer. The second operating mode functions as a block down-converter with a broadband IF up to 20 GHz. Power to the module is provided via an included external DC power supply. These frequency extenders minimize conversion loss by multiplying and amplifying the LO signal internally, thus taking advantage of the benefits of low harmonic mixing. This architecture also preserves the X-Series precision frequency resolution and low phase noise, extending those qualities into the millimeter and sub-millimeter bands.
-
product
Frequency Multipliers
Analog Devices active and passive frequency multipliers enable designers to economically multiply lower frequencies to higher frequencies without creating measurable additive phase noise. This broad portfolio features a range of devices that can meet the size, volume, and cost needs for multiple applications, including:
-
product
Torque Multipliers
Mountz torque multipliers make tough nuts easy to crack. They boost productivity, giving your workers the power to quickly turn the large fasteners found in the aerospace, transportation, mining, marine, oil/gas, and power generation industries. Mountz torque multipliers can improve process control compared to less controlled options, like impact drivers, and they guarantee quality of work. They generate less reaction torque than impact drivers as well, protecting your workers and their projects from harmful hammering. Electric and pneumatic torque multipliers are also much faster than hydraulic ratchets, helping you get more work done in less time. To top it off, they’re quiet, reducing the din of the workplace and helping to prevent hearing-related injuries.
-
product
Pulse Signal Amplifier
VCH-606
The pulse signal amplifier VCH-606 is designed to multiply a single pulse or a sequence of pulses to 16 independent outputs. The impulse signal amplifier includes 16 independent channels with unity gain each for connecting consumers of impulse signals with an input impedance of 50 Ohm.
-
product
RF Multiplier
Devices that produce an output signal where the frequency is a multiple of the input signal.
-
product
Sub-Harmonic Mixers
Subharmonic mixers are composed of a passive mixer with a subharmonically pumped (×2) local oscillator. These mixers allow designers to use low LO frequency, which eases the need to generate a high frequency LO signal. For high frequency application design, Analog Devices subharmonic mixers offer a simpler alternative to traditional mixers with no LO multiplier.
