Test Boards
See Also: Board Test, Testboards, DUT, Extender Boards
-
product
VME Test Extender 6U/220mm 64X w/o P0
116EXT6122-012XR
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME Test Extender 3U/400mm J2
111EXT3140-12xx
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
product
Flying Probe Testers
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
product
Meter Test Board
MTB
The accuracy of TESCO’s Meter Test Board (MTB-3050) is now available in multi-position test boards to perform individual or simultaneous accuracy tests in the meter shop!
-
product
Flying Probe Test
Producing the highest quality test programs since 2005, Test Coach is the proven specialist firm for flying probe test. Our in depth knowledge of SPEA systems and over 10 years of honed flying probe test techniques guarantees that our test programs offer the highest test coverage possible. As an In – Concert Partner with SPEA, we work closely with their team to keep at the forefront of new product innovations and technology, so that we can provide the latest advancements to our customers. In addition to test program development, we offer board test services, maintaining the systems and staff that allow for high throughput and the ability to consistently deliver the rapid turn times that customers can depend on. And, with 7,000 square feet of space, we feature a modern, clean, ESD safe and ITAR registered facility that surpasses expectations.
-
product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
product
Test Board For QSFP+ Transceiver
EQSFP10
The OPTELLENT EQSFP10 is a cost-effective and convenient test board for testing QSFP/QSFP+ optical transceivers in R&D and manufacturing environments. The EQSFP10 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP10 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
FMC Loopback Test Board
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
product
Clamshell Type Mechanical Fixtures
Series 11
The MT Series 11 dual well mechanical kits are an affordable solution to printed circuit board testing with the advantage of testing two devices. These can be similar devices, or devices that are used together in a functional test. The Series 11 Kits have the same available features and options as the Series 10 Kits.
-
product
Meter Test Board
MTB-3200
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
-
product
Clamshell Type Mechanical Fixtures
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
product
Three Phase Meter Test Board
MTB-3050
TESCO’s MTB-3050 is a Three Phase Meter Test Board with every laboratory feature you could want along with metrology and software suitable for your production meter testing needs.
-
product
Spring Probe For Testing Bare Board And/or PCB
You can see Spring Probe for testing bare board and PCB here. Standard pitch is from 0.5mm to 3.0mm.
-
product
TIM Characterization Tools
Thermal Engineering Associates, Inc.
Combining Thermal Test Vehicles (TTVs) with Thermal Test Boards (TTBs) results in a set of tools that perform the basis for TIM thermal characterization under application-oriented measurement conditions. Availability of these tools creates a de facto standard that enable both TIM manufacturers and TIM users to compare measurement results under the same conditions.
-
product
A-Base Test Board Adapter
1182 and 1183
From time to time, you may find yourself needing to test A-Base meters. Or perhaps you will need to test them for the first time in years as part of a removal project. Well, TESCO can help with the A-Base Test Board Adapter!
-
product
Software & Hardware Interface
XJAPI
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
product
Programming on-chip flash in your processor
XJDirect
XJDirect is an advanced and innovative method for programming the internal flash of your processor and implementing some aspects of board test through JTAG when traditional boundary scan techniques cannot be used.
-
product
USB Type-C Test Fixture | CB26U | Cable Harness Tester
A leader in development of PC-based cable and wire harness, continuity, resistance and hipot test systems for over 20 years, CAMI offers the CableEye suite of products complete with accessories – including “connector boards”. The selection of these test fixture boards is constantly growing and is currently numbering over 60 – most of which are populated with ‘families’ of connectors. When pre-populated boards are used, the tester GUI automatically displays a graphic of the connectors under test.
-
product
ASA240
The ASA240 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA240 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board. The built-in gate/bias generator (+/-10V, 100ohm source impedance) can be used to help test active components such as SCR’s, opto-couplers, small relays, TRIAC’s etc. An external dual footswitch can be connected to the ASA200 and can be user configured to control various functions.The built switching matrix (40 x 2) is easily configured from the software and maybe used with adaptors (such as DIP or SO) to speed up testing of boards, or maybe connected to a ‘bed-of-nails’ to facilitate rapid testing of boards in production.With the ASA240 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at an affordable price.
-
-
product
DUT Prototype Board
DPB8800
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
product
4X14 Gb/s QSFP/QSFP+ Evaluation Board
EV-QSFP-174
The EV‐QSFP‐174 QSFP/QSFP+ Host Test Board comes complete with Windows based software (Windows XP & above) to enable intuitive memory map programming and testing, controlled via a mini B USB port. It is designed to simulate an ideal environment for QSFP/QSFP+ transceiver module testing, characterization and manufacturing test. Its high speed properties make the host board as electrically transparent as possible, allowing for a more accurate assessment of the module’s performance.
-
product
FPGA Test System
DO-254/CTS
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
product
Cardboard Puncture Tester
DRK104A
Shandong Drick Instruments Co., Ltd.
DRK104A cardboard puncture tester is used to test the corrugated board anti-pierced performance (puncture strength). It has the snap-operating handle, automatic reset and safety protection function. It is the indispensable instrument for carton manufacturing plants, research and quality supervision, inspection and other enterprises and departments.
-
product
Adjustable Press Plate Bed of Nails Testers
Protector Adjustable Family
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
product
Development Boards
Advantech Development boards provide a schematic software & reference to reduce design effort at the development stage. Development Boards have been designed in order to allow customers to verify the functions of COM, text carrier board problems and support COM series. Advantech has designed a Development Board which can be used to test carrier board problems and support COM series, and Qseven, ETX / XTX form factors.
-
product
Kelvin Test Contactor
nano
nano Kelvin™ test contactor is a well-established Cantilever Kelvin test contactor with proven performance in the automotive market and further increasing popularity due to the robustness and reliability of the product.Featuring a small imprint area, contact motion decoupled from the test board and simple and cost-efficient test boards.
-
product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
-
product
RELIABILITY BOARD (Reliability Test Board)
The reliability test board is used for testing of HAST, THB, HTOL, BURN-IN, etc. It is a product that evaluates the environmental test and durability when applied to actual products such as lifetime test, high temperature, low temperature, high humidity and thermal shock
