Filter Results By:
Products
Applications
Manufacturers
BNC
-
product
Environmental Test Probe, PH, Tenma 72-6783 PH Meter
72-6784
The 72-6784 is a typical 0 to 14pH Probe with epoxy body, BNC connector. It is used with pH meter 72-6783 model.
-
product
Changeover
LT 4448
LThe LT 4448 is a changeover unit that automatically switches the signal from the primary signal to the backup signal when problems are detected in the primary signal.Two systems of input signals (primary and backup) are connected to the LT 4448, and the LT 4448 detects errors in the amplitude of the primary input signal.A single LT 4448 provides 11 pairs of BNC and LTC channels. These channels can receive SDI, NTSC/PAL black burst, HD tri-level sync, AES/EBU digital audio, word-clock, and LTC signals.It can be used in combination with the LT 4610 (Sync Generator).
-
product
Fast Timing Analysis
Zero-Time Box
The Zero-Time Box is designed to compare the start times of source units with the recording system. It is compatible with every source encoder that outputs a start signal on a BNC connector, and also supports every source controller and decoder that does the same. The Zero-Time Box can also be used as a 5 channel precision measurer of timing intervals.
-
product
75 Ohm BNC to MCX Adaptor Assembly
40-978-781-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Multi-Conductor Cables
16 Channel, multi-conductor cables are shielded and wired for PCB® equipment specifically. Shielding minimizes noise when located near other power or signal cables. Custom versions are also available on request. Instrumentation-grade BNC / DB-50 connectors are provided to interface with Patch Panels and Signal Conditioners.
-
product
Primus Epic Interface Kit
LANTAP-10
Innovative Control Systems, Inc.
*LANTAP-10 kit comes with 10’ Coaxial cable, 6’ USB cable, 6’ CAT5 cable, BNC Connector and Terminator.*Allows connection of any 10/100/1000 Ethernet equipped system to EPIC equipped *Aircraft LAN or ANY 10base2 need.*No drivers to install. The LANTAP is NOT a USB device. It is only powered by USB.*Complies to IEEE 802.3 10Base-T and 10Base2*LED diagnostics and monitoring indicators
-
product
8-Channel BNC Break-out Card
ProDAQ 5824
The ProDAQ 5824 Signal Conditioning Cards are designed to facilitate the interface of the ProDAQ 3424 8-Ch. 24-bit Sigma-Delta ADC Function Cards to a number of sensor types. It does this by providing 8 BNC connectors on the input and a 3424 pin-compatible 50-pin SCSI on the rear of the card.
-
product
50 Ohm SMB to BNC Adaptor Assembly
40-978-501-1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Readout passive probe
Rngs around the BNC input sockets that allow the attenuation factor of attached probes to be detected by the scope.
-
product
InfiniBand to BNC Cable, AI0-7 for PXIe-4492
787916-01
16-Pin K-Type Male InfiniBand to 8 1-Pin BNC Male, 50 Ohm Coaxial Cable - The SHB4X-8BNC is a coaxial cable that connects data acquisition and control devices.
-
product
LXI Dual 24 X 8 Video Matrix, SMB (50R)
60-711-721
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75 Ohm with the option of SMB or MCX connectors or, with a larger case size, BNC connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-711 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
product
Cable Assembly, Receiver, TriPaddle & Mini Coax, 36", 9-Pin DIN, 3 BNC Plugs and SMB Plug
540037010211
Cable Assembly, Receiver, TriPaddle & Mini Coax, 36", 9-Pin DIN, 3 BNC Plugs and SMB Plug.
-
product
Probe Adapters
Probe adapters provide simple and easy interface of third-party probes as well as change between the different Teledyne LeCroy Oscilloscope input and cable types (ProBus, ProLink, K/2.92 mm, BNC and SMA). Depending on the adapters, changing between the Teledyne LeCroy Oscilloscope's input type may have an effect on the overall performance of the channel.
-
product
2m BNC Test Cable
16048D
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
product
UHF/RFID/TETRA Power Divider Combiners
INSTOCK Wireless Components, Inc
INSTOCK Wireless 350-1000 MHz RF power divider combiners are optimized for UHF, RFID, and TETRA power splitting and combining applications. Wireless microphone systems also typically operate in UHF frequencies, making an INSTOCK device ideal for splitting or combining antennas in UHF wireless microphone systems. Available in 2-way thru 48-way configurations with Type N, SMA, TNC and BNC connector configurations INSTOCK.
-
product
LXI Single 24x8 HF Matrix, BNC (75R)
60-711-005
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75 Ohm with the option of SMB or MCX connectors or, with a larger case size, BNC connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-711 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
product
RF Connectors
HD-BNC Connectors
The HD-BNC product line delivers both true 50 and 75 ohm performance in a footprint 4 times smaller than traditional BNC connectors. Using the same cable prep and termination specifications of legacy broadcast connectors makes adopting HD-BNC seamless.
-
product
Dual Channel HV Amplifier with Phase Inverter
A400DI
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
product
Digital ICP® - USB Signal Conditioner
The Digital ICP®-USB Signal Conditioner, Model 485B39, offers plug-and-play connectivity for your measurements. Model 485B39 from The Modal Shop, a wholly owned subsidiary of PCB Piezotronics, is a pocket-sized, dual-channel ICP to USB digital signal conditioner. The unit provides any ICP sensor – accelerometers, microphones, impact hammers, laser tachometers, and more – with a digital USB output. It is truly plug-and-play, with no drivers required. Digital ICP features two BNC inputs and a 24-bit USB digital signal output, allowing a direct connection from the sensor to any PC, tablet, or smartphone device for easy data collection, analysis, and sharing on-the-go.
-
product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8 KIT
This K-AN8 (8 analog + 4 digital input) kit contains everything needed to get the K-AN8 set up and tested on a work bench.To help with connecting sensors to the analog and digital ports the K-BoB enables easy connection with BNC connectors.Influx K-Cal is easily connected via the Kvaser LeafLight interface and Kvaser T-CANnector. (Using the Kvaser T-CANnector to power up the K-AN8 (at the desk) and terminate the CAN bus).
-
product
Electromechanical Programmable Attenuators
BroadWave manufactures single section 6 dB to 8 section 0 – 127 dB programmable attenuators. •Voltage control and external TTL control •RF Connectors: BNC, N, SMA and TNC •50 and 75 Ohm
-
product
SMB Female to BNC Female Cable, 50 Ohm, 8 cm
781449-01
The SMB-BNC Coaxial Cable, sometimes referred to as SMB-100 or SMB-110, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths and quantities.
-
product
Low Noise Differential Preamplifiers
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
product
BNC Connectors
Pasternack BNC connector category includes many part numbers, most are RoHS and REACH compliant. BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC connectors are built to precise industry specifications. BNC connector items are constructed in male or female gender in standard polarity or reverse polarity threads, with 50 Ohm impedance. Connectors in BNC series are available in straight or right angle versions, as well as, 4 hole flange, bulkhead, 4 hole panel or mountless options. These BNC connector designs include clamp/solder, crimp/solder, field replaceable, solder or solder/solder attachment methods. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this BNC connector series is in-stock. Not only in stock, but these BNC connectors will ship the same-day as they are purchased.
-
product
Picolo PCIe
BNC, DB9 and S-Video connectorsPCIe x1 busAcquisition of composite or separate video (S-Video) signalsOne video decoder, 25/30 images per second (50/60 fields per second)PCI and PCIe versions available
-
product
Turnkey Portable Acquisition Systems
Series 6800 for portable applications is a ready-to-run, high performance measurement system that is DC powered for mobile applications. All connections are front mounted for easy installation in tight places or on the go. 6800 systems come equipped with a conditioner, amplifier, filter and digitizer. Each channel has a front mounted connector specific to a measurement type: RJ-45 for 8-wire bridge transducers or BNC for voltage or ICP/IEPE inputs.
-
product
Capacitive Divider
It can be chosen as PD sensor for Techimp PDCheck, PDScope or PDBaseII systems. It is suitable for on line or off line PD tests onrotating machines, for both spot measurements and monitoring applications. A BNC termination is available to connect the coupler through a coaxial cable.
-
product
Cable Testers
Passage test:Detects open wires, short circuits and faulty wiring. Pass / fail test using a given pattern cable. Finding intermittent connections.Save cable data for documentation purposes. Print wiring diagrams. Printing labels. Log and print error logs.Graphical representation of the wiring of cables, graphical comparison of two cables. Easy, intuitive, graphical tracking of individual wires of a cable.Quickly install quick-mount boards for a variety of connector types such as BNC, RJ45, Sub-D, flat-ribbon connectors, and many more.Easy connection to the PC via USB .Light Director System:LED-led assembly of connectors. Optional also with voice output. High degree of safety due to fault checking during assembly.
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
Picolo Alert PCIe
4x BNC connectors on the bracket, expandable to 16 with three [1203] VEB modules (sold separately)PCIe x1 busSixteen shared video decoders, 100/120 images per second (200/240 fields per second)Real-time acquisition from 4 cameras, fast switching between up to 16 camerasIndependently-programmable frame rate and acquisition parameters for each video input
