Filter Results By:
Products
Applications
Manufacturers
Verification Test
qualifies that UUT meets design requirements and specifications.
-
product
Modular Components & Test Sets
Kratos Defense & Security Solutions, Inc.
Kratos offers a full suite of Flight Termination System modular components and test sets. Modular components can be used individually for system verification, testing, troubleshooting, and low power flight termination requirements or can be combined with other components to form complete turnkey flight termination systems.
-
product
Bus Analyzer
Goebelyzer
Our Goebelyzer analyzer systems offer unparalleled insight into bus data and are used in flight test, system simulation, LRU design, verification and manufacturing test. Supported Interfaces Arinc 664, ASCB-D, Honeywell Flight Controls P2P, Arinc 429, CAN2.0b, Mil Std 1553, RS 422 SDLC/Async, ADC
-
product
RF Signal Generators
Compact and reliable microwave and RF Signal Generators for use in automated testing environments, production verification, EMC testing, educational institutions, aerospace, defense projects, LTE engineering, satellite communications, CATV, 5G design…
-
product
Radio Conformance Analyzer
RCA G9200
LTE test solution for development, verification and conformance testing of LTE mobile equipment. The G9200 RCA is able to perform analysis of LTE mobile devices at all layers from the physical to the application layer, and is suitable for development, conformance, pre-conformance, and production test applications.
-
product
Automotive Ethernet Rx Compliance Software
AE6910R
Unlike CAN, LIN, or MOST, the IEEE standard for automotive Ethernet demands rigorous compliance verification using specific test cases. The test requirements include complex measurements: vector network analysis with S-parameters, bit error rate (BER) test, and protocol analysis of high-speed digital signals.
-
product
Automotive Ethernet Tx Test Software 10M To 10Gbp
AE6920T
Unlike CAN, LIN, Automotive Ethernet demands rigorous compliance verification using test cases that cover transmitters (Tx), receivers (Rx), and harness/connector assemblies. To help you save time and effort, Keysight offers solutions that automate the testing and validation across Transmitter (Tx), Receiver (Rx), and the connections between Automotive Ethernet devices. Our engineers have invested thousands of hours in learning the standards and creating automated, repeatable compliance tests. These proven applications help you ensure proper test configuration and valid measurement results. Ultimately, you’ll have greater confidence that your device is compliant. Now available for data rates up to 10Gbps. The automotive Ethernet test solution AE6900T offers hardware and accessories to make sure you have all of the components you need to get up and running quickly.
-
product
Electrical Testing
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
product
Measurement & Test
Electronic test engineers use a variety of precision instruments for R&D, vendor verification, and production testing. ETPS can supply a number of general test instruments that can be used in stand alone mode or automated for high throughput testing. Dedicated battery test systems with automatic charge and discharge modes with data logging are available. The standard 16 and 32 channel systems have range up to 5VDC ensuring their suitability for a wide variety of cells.
-
product
Test Program Modules
The BRAT Test Program developed will provide functional validation of an assembly based on customer supplied documentation. This does not include hardware (e.g., Interface Test Adaptors), documentation (e.g., technical orders), travel or travel related per diem, or site verification test or installation.
-
product
Handheld Particle Counters
Models 3888 And 3889
Kanomax’s innovative Handheld Particle Counters (Models 3888 & 3889) set the standard of instrumentation in cleanroom / operating room monitoring and verification, filter testing, IAQ investigation, data center cleaning and many more highly specialized and highly sensitive applications. These beautifully engineered devices boast some of the most highly advanced technology in the industry. A combination of accuracy and practicality, these devices count airborne particles with high quality performance.
-
product
Manual Switch Boxes
RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.
-
product
MCB Thermal Verification Test Bench
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
product
Measurement and Analytics Solutions
Based on our OTP² system platform, we were able to implement a family of scalable test systems which is based on a common systems architecture, e. g. for products in the area of chemical analytics measurement. We not only implemented a universal, extremely comprehensive test system, but also a series of compact systems for benchtop placement which are fully compatible with the larger, universal system. Our specialized self-test adapters and test software enable fast verification of the test systems as well as partly automated calibration by the customer.Our systems are also used in electrical measurement applications, e. g. for calibrating analog input assemblies for PLC technology. For this purpose, specialized calibrators are integrated into the system; they provide traceable calibration of the relevant stimulus signals.
-
product
FPGA Test System
DO-254/CTS
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
product
Ethernet Testing Network Performance
Networked Communication Solutions, LLC
Xena Networks and Veryx Technologies have created an innovative Ethernet test platform that combines Xena’s high performance, wire-speed Ethernet test hardware with Veryx’s broad portfolio of IP & Ethernet functional and conformance test suites. The result: an affordable, high-performance platform for IP & Ethernet load stress, protocol conformance & functional verification testing.
-
product
Bench Power Supply
E3630 Series
When your requirements demand more power, the E3630 Series power supply offers up to 200 W per output. This linear power supply meets the requirements of the most demanding applications in R&D design verification, production testing, and quality assurance (QA) verification with reliability you can count on.
-
product
PCI High Density Resistor Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-295A-021-3/24
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Dial Torque Screwdrivers
A dial measuring torque screwdriver is designed for torque testing and torque verification. It is a versatile tool that is utilized for torque auditing and product evaluation. It can be used to monitor torque as it increases or decreases or display peak torque applied. The dial screwdriver is used in two common torque verification tests. One is the first movement test and the second is the loosening test. The screwdriver is standard instrument in engineer’s tool kit.
-
product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PAT Check Box
369A910
The only check box to provide comprehensive verification of 17th Edition and PAT test equipment. The Powercheck tests for full earth continuity, insulation, resistance, RCD trip time, RCD trip current, touch current and flash test verification.
-
product
Wound Component EST Scanner
19035
The quality verification tests for wound components consist mainly of AC/DC Hipot tests and insulation resistance (IR) tests. The Chroma 19035 wound component EST scanner series perform safety tests for motor, transformer, and heater related wound products.
-
product
Compact, Easy To Use Tester.
Eye-BERT 40G
The Eye-BERT 40G packs 40Gbps of test capability and a color touch screen into a compact, easy to use tester. The Eye-BERT 40G offers high performance stand alone bit error rate testing at a fraction of the cost of competing testers. Its small size and stand alone operation allow for convenient field testing of QSFP transceivers as well as link verification and performance testing all in a single unit. The automated QSFP test feature also allows the user to quickly verify transceiver performance and automatically generate a report complete with unit serial number.
-
product
Regenerative Grid Simulator
61800 series
Market demand for Distributed Resource (DR) products such as PV inverters and wind energy systems is steadily growing as the world strives for clean renewable energy sources. This demand has created a need for rigorous regulation testing to standards such IEEE 1547 / IEC 61000-3-15 / IEC 62116 ensuring proper and safe operation of on-grid products. It has become critical to manufacturers to conduct these tests to prove compliance and to relieve product liability concerns. Chroma’s new 61800 family of Grid Simulators has been designed to fulfill these test requirements by providing a full 4 quadrant, fully regenerative, grid simulator with advanced features for compliance, safety and product verification testing.
-
product
PXI 8 Trib Daisy Chain Switch 120Ohm Balance
40-795-001
The 40-795/796 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data over 100 or 120 balanced lines.
-
product
Automated Test Environment
AS5657-ATE
The AS5657 Automated Test Environment (AS5657-ATE) is designed to automate device compliance testing according to the SAE-AS5657 “Test Plan/Procedure for AS5643 IEEE-1394b Interface Requirements for Military and Aerospace Vehicle Applications”. The purpose of this tool is to automate and simplify the task of AS5643 compliance verification and testing, which of course is essential for device compatibility within avionics and aerospace programs.
-
product
PXI Multifunction I/O Module
The PXI Multifunction I/O Module provides I/O with varying numbers of channels, sample rates, and output rates with precise timing, triggering, and synchronization between models. This module can be used for industry applications such as laboratory research, design verification test, and manufacturing test.The PXI Multifunction I/O Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Squeak And Rattle Test Solutions
Annoying noises like squeaks and rattles have become a significant quality issue for customers of passenger vehicles, light & heavy commercial vehicles, increasingly off-road vehicles, and even airplane applications. These unwanted sounds are a problem for numerous reasons including customer dissatisfaction, sizeable warranty expense, and the overlying difficulty to diagnose and fix. MB Dynamics offers an innovative line of Buzz, Squeak & Rattle (BSR) or Squeak and Rattle (S&R) Test Solutions, focused on helping to eliminate annoying noises through prevention, design verification testing, and production verification testing, before the product reaches the customer. -
product
Introduction to Graphical User Interface - Softpanel
61800 Series
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
ADSL / 2 / 2+ Handheld VoIP Tester
QuickTest 500
*Rapid Testing. The QuickTest 500 ADSL2+ Tester's automatic Service Verification Test Suite starts as soon as you switch on (results are typically obtained in less than 3 minutes)*Simple to use. Virtually no product training required with QuickTest 500 ADSL Tester*Configurable Pass / Fail Indicators on the LCD display and clearly presented in multi-colour LEDs on the front panel*No need to get a laptop out*Save and name up to 16 test results at any one time*Line Voltage LED indicates poor, missing or excessive Line Voltage*ADSL/2/2+ Test LEDs to indicate if ADSL Showtime achieved*In Service LED indicates problems with PPP or IP layer*LEDs to indicate problems with the Trained Line Rate, poor Noise Margin or excessive Line Attenuation
