Wafer Level Reliability
-
Product
Probe Card
VC43™/VC43EAF™
-
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.
-
Product
Multisite Probe Card
T300 ButtonTile™
-
The Celadon T300™ probe cards are designed for long-term, multi-site, high-density wafer level reliability or burn-in tests up to 400°C. In today’s economic environment, conventional reliability data is needed quickly while eliminating the cost, electrical stress, and delay of parts packaging while maintaining a wafer performance map.
-
Product
Probe Card
T90™ Series
-
The 90 mm tile was designed for mounting on a standard 4.5″ probe card holder for multi-site wafer level reliability testing. The 1.6 mm (0.062″) thick rails allow the chassis to slip into planarity adjustable probe card holders for most analytical probe stations.
-
Product
Probe Card
VC20E Series
-
The 20mm VC20 is a highly adaptable probe card solution for a wide variety of tests including Modeling & Characterization, Wafer Level Reliability or Parametric Test. It can be easily combined with different interfaces to create modular probe cards supporting Keithley, Keysight or other custom tester platforms. Probes can be configured in either single or dual layer.
-
Product
MPI Automated Probe Systems
-
MPI Advanced Semiconductor Test
MPI’s 200 mm and 300 mm automated probe systems are dedicated and designed to address current and future requirements for all facets of Device Characterization for Modeling and Technology/Process Development, Failure Analysis, Design Verification, IC engineering, Wafer Level Reliability as well as special requirements for MEMS, High Power, RF and mmW device testing.
-
Product
Semi-Automated Probe Stations
SPS 2600, SPS 2800, and SPS 12000 Series
-
The SPS 2600, SPS 2800, and SPS 12000 Series systems are MicroXact’s semi-automated probe stations designed to be flexible and easy to use when performing high productivity device characterization, wafer level reliability testing and failure analysis. These semi-automatic probe station systems are designed to support manual and semi-automatic probing of up to 200mm wafers.
-
-
Product
System to Handle Wafer Levels
AMI AW Series
-
Operator-Free Wafer Inspection, Analysis and Sorting The AW Series are advanced high-capacity, high throughput automated wafer C-SAM® instruments specialized to deliver maximum sensitivity for the evaluation of wafer and device level applications.
-
-
Product
MultiSite Test sockets and Wafer Level
-
multi-site sockets include anything from strip test sockets to test sockets for wafer test to multi-position, singulated devices. The advantages of these sockets can be enormous as test time can be decreased by a factor of ten over conventional one up testing. In most cases, the throughput is only limited by tester capabilities and/or handling capacity.
-
Product
Production Wafer Level Burn-in
-
TV19 VersaTile™ probe cards are designed with Celadon’s patented ceramic technology for superior electrical performance, yet is highly modular due to it’s 28mm x 28mm chassis. Micro-adjustments can be made in seconds with an allen wrench and a microscope. Easily align VersaTile cards for different wafer layouts using a 4.5” compatible 1×3 , 200mm, or 300mm VersAdjust plate.
-
Product
Wafer Prober
Prexa
-
The latest fully automated 300mm wafer prober. The system offers excellent productivity and advanced functions, contributing to KGD (known good die) testing for advanced packaging.
-
Product
Lighting Reliability
-
LED/OLED package lifetime is highly dependent on thermal management, and LED lamp performance can be dependent on the luminaire in which it is installed. Lighting reliability test system for LED/OLED Products are widely used for normal /accelerated aging, lumen maintenance measuring, lifetime evaluation and temperature characteristic testing for LED/OLED products including LED package, array, module, OLED module and luminaires.
-
Product
Wafer Test
-
Based on the reliability test, CSE conducts the test of the IC chip through electrical signals to the semiconductor wafer. We provide various Test Solutions according to the needs of designers/manufacturers. by sorting out good and bad products.
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Reliability & Enviromental Testing
-
NCEE Labs has been providing industry-standard reliability and environmental testing for 20 years. Our experienced testing staff can assist you in determining the type or level of reliability/environmental testing you require for your products!
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
Level Controllers
-
Measure and control fluid levels in a contained area or facilitate automatic filling and emptying operations with Omega's dependable single and multi-sensor level controllers.
-
Product
Wafer Prober
Prexa MS
-
The latest fully automated 300mm wafer prober for memory devices. Featuring high rigidity and exceptional thermal control, the system enables full-wafer contact testing.
-
Product
Level Meter
LM86
-
Beijing Airport Beiguang Instruments Co., Ltd
The basic version magnetic level gauge.
-
Product
Wafer Probe Loadboards/PIB
-
DTS has a full line of standard PIBs for all major tester platforms. Custom PIB designs can accommodate any test head, prober and manipulator configuration, including probe card changers, overhead direct dock setups and cable interfaces. DTS wafer test loadboards are compatible with a variety of pogo pin interface towers. All PIBs are constructed with impedance control, precision matched line lengths, full power and ground planes and both analog and digital resources to provide high quality signal integrity directly to the device.
-
Product
Reliable CAN Measurement Technology
CNT evo CAN MM Series
-
The CNT evo is a high-precision measurement module designed for measuring frequencies, pulse widths, incremental displacement measurements, rotation angles, position measurement, event counting and period measurements.
-
Product
Wafer Chip Inspection System
7940
System
Chroma 7940 wafer chip inspection system is an automated inspection system for postdiced wafer chip inspection.
-
Product
Reliability And Durability Testing
-
Underwriters Laboratories Inc.
Our reliability and durability testing services provide an accurate assessment of how your product may perform under expected and unusual use. We can help you meet regulatory requirements, gain actionable knowledge about the anticipated life cycle of your products and identify design flaws that have adverse effects on a product’s reliability and durability.
-
Product
Level Sensors
-
Intelligent solutions for level and point level measurementWhether for continuous level measurement, point level measurement or both – SICK offers a wide range of solutions for process engineering, storage, and protection. Based on the installation situation, medium properties, and environmental conditions, SICK provides sensors that ensure efficient processes. As the provider of one of the broadest technology portfolios, SICK brings its knowledge to the forefront.
-
Product
Wafer Auto Line Integration
-
The line is used for semiconductor wafer grinding. It carries out material matching and distribution, automatic loading and unloading, auto focusing and positioning and many other functions. The grinding precision is 2μm(3-sigma). It is also capable of collecting and analyzing real-time production data and interfacing with MES system.
-
Product
Reliability Testing Services
-
Innovative Circuits Engineering, inc
Our Reliability Testing Services make it possible for us to work with many different customers who manufacture devices that need tests such as pressure pot, temp cycle and more.The focus of our reliability testing lab is to provide our customers with an array of services and tests that fulfill all of their reliability testing needs. Whether you need preconditioning, thermal shock, pressure pot, or many other reliability testing needs, we are happy to be of service.
-
Product
Wafer Internal Inspection System
INSPECTRA® IR Series
-
An infrared internal defect inspection system has been added to the INSPECTRA® series.It is now possible to inspection with both infrared and visual light in one system.
-
Product
Fault Level Monitoring
-
The fault level or fault current is the maximum current to flow on a network in the event of a fault.
-
Product
Radar Level Transmitter
DR5400
-
DR5400, FMCW 24 GHz open air radar is a market entry level transmitter for liquids in basic process applications. This model has proven PP Drop antenna design which is insensitive to condensation.
