RF Wattmeters
Measure RF power.
-
Product
PXI Hex SPDT RF Switch 6GHz 50 SMA Terminated
40-880-003
Switch Module
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
Product
RF Connectors
BNC Connectors
-
BNC connector types feature a bayonet style coupling mechanism that allows for quick connect and disconnect with positive locking. Mating is achieved with just a quarter-turn of the coupling nut. With a classic, dependable design, BNC RF connectors are suited to accommodate a large variety of RG and industry-standard coaxial cables, in a variety of termination styles.
-
Product
3D RF Noise Measurment System
EMI-360
-
3D RF Noise Measurement System EMI-360 to realize the new EMC measurement.EMC measurement is possible to realize a low-cost and time reduction.
-
Product
Noise Bridge, RF 1 MHz to 100 MHz
MFJ-202B
-
Quickly adjust almost any antenna for maximum performance, 1 to 100 MHz. Lengthen or shorten your antenna for minimum SWR. Measure resonant frequency, feedpoint resistance and reactance. Works with any receiver or transceiver. Hand-calibrated resistance scale, expanded capacitance range and exclusive built-in range extender.
-
Product
RF Multi-Coupler
MC108-2
-
Systems Engineering & Management Company
The MC100 Series Multi-Coupler is a 1U Rack-Mount device that provides RF distribution form 200 MHz to 5250 MHz. Both single and dual output configurations are available, as well as up to 8 output channels. Each output is an independent channel with +/- 5 dB gain controls, providing the ability to balance all outputs within +/- 1 dBm. Frequency Channel selection is from both front panel controls as well as remote control via Ethernet and SEMCO's MCCS Network software program.
-
-
Product
Process RF Sensors
-
Process RF (radio frequency) analyzers using penetrating radio waves to determine the moisture content across a full sample thickness. Single point, array and hand-held analyzers provide a variety of sampling options from fully integrated in-process moisture profiling to at-line quality control. RF analyzers are widely used in gypsum, panel board, and other industrial processes.
-
Product
Fixed Aperture RF Current Monitoring Probe
TBCP1-200
-
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
-
Product
MS-M Style 26-Pin RF Cable Assembly, Female To Unterminated, 2m, RG178 Cable
40-979A-526-2m-FU
-
This 2m long MS-M style RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with FEP insulation and an attenuation of 102dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
RF Shielded Test Enclosure, Largest Rack Mountable Enclosure
JRE 1724
-
Originally designed for testing wide screen laptops, the rack-mountable JRE1724 is ideal for large wireless devices such as; Mesh Network AP's, Cellular/LTE/4G Base Stations, and other large RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble free operation over its lifespan. Internal struts keep the lid open for easy internal access when connecting the device under test.
-
Product
FieldFox Handheld RF Analyzer, 4 GHz and 6 GHz
N9912A
-
CAT and VNA: 2 MHz to 4/6 GHzSA: 100 kHz to 4/6 GHz Carry the world's most integrated handheld RF analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional T/R VNA, spectrum analyzer, built-in power meter, and more Save time by measuring RL and DTF simultaneously in the same sweep Calibrate simply in the field with Quick Cal Easily measure average and pulse power with a USB power sensor
-
Product
RF Matrix Switch for Wireless Technologies up to 4 GHz
NEXUS-4
-
Quintech Electronics and Communications Inc.
The NEXUS-4 is a bi-directional fully non-blocking 3232 RF matrix switching system that can route any input ports to any outputs in a 6 RU chassis. With the frequency range of 700 MHz to 4 GHz and the capability of expanding to 256256, it enables large scale wireless testing that involves many MIMO base stations and devices. The built-in programmable attenuators and efficient automation interface provide ease-of-use testing of signal fade and emulation of mobility scenarios. It can dramatically increase lab efficiency by eliminating manual patch panel and cabling as it can be remotely reconfigured for different test setups consistently in seconds.
-
Product
EMC & RF Solutions
-
Microwave Absorbing Material Characterization System that measures the signal loss through a material sample in a frequency range of 5 15GHz (with the option of extension to lower frequencies).
-
Product
EXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5172B
Vector Signal Generator
Achieve faster throughput and greater uptime with cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading ACPR, EVM, and output powerReduce the time you spend on signal creation with Signal Studio software; purchase only the waveforms you need with 5- and 50-pack licensingMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
Product
RF Shielded Box
LTL Q20001
-
LTL Q20001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL Q20001 RF shielded test enclosure can comfortably house the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
Dual 16 to 1 50 600MHz PXI RF Multiplexer
40-764-002
Multiplexer Module
This dual 16 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI/PXIe RF Multiplexer, Triple 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-003
Multiplexer Module
This multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40/42-882B MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
Product
FieldFox C Handheld RF Analyzer, 4 GHz
N9913C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
PXI Dual 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX
40-874-102
Multiplexer Module
The 40-874-102 is a 50 Ohm 8 to 1 RF multiplexer with 2 banks in a single PXI slot. It has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40-874 has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe RF Matrix, 16x4, 100 MHz, 75 Ω SMB With Loop-thru
42-727A-101-L
Matrix Switch Module
The 40-727A-101-L (PXI) and 42-727A-101-L (PXIe) are 16x4 75 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI 16x4 RF Matrix 100MHz 75 SMB With Loop-Thru
40-727-101-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
Single 32 to 1, 50 600MHz PXI RF Multiplexer
40-766-001
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Single 32 To 1 Terminated 50Ω 600MHz PXI RF Multiplexer
40-767A-001
Multiplexer Module
The terminated single 32 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
KEINOS™ 2 MHz 5 KW, 11 KW & 13 KW RF Plasma Generators
-
The KEINOS™ 2MHz plasma generator builds on the solid, reliable attributes of the existing 2MHz design. KEINOS™ incorporates the latest technology from MKS to enable demanding applications of pulsing, fast impedance changes and shorter process steps. KEINOS™ can deliver up to 13kW of power, pulsing up to 50KHz, multiple set point pulsing, pulse shaping and MKS patented frequency tuning. KEINOS™ uses an integrated VI sensor for power accuracy and digital based control for fast response times.
-
Product
RF Power Splitter, Combiner, Divider RoHS, 8 Way, Type-N Female, 698 - 2700 MHz, 50 Ohm
PD2080
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy Type N Female (Jack) Low PIM
-
Product
PXI/PXIe RF Matrix, 32x4, 150 MHz, 50 Ω, SMB, With Y Loop-thru
40-724-022-L
Matrix Switch Module
The 40-724-022-L (PXI) and 42-724-022-L (PXIe) are 32x4 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - XMC
Model 71690
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal - levels with up to 60 dB gain- Programmable analog downconverter to I + Q baseband signals - 4 to 40 MHz bandwidth- Two 200 MHz 16-bit A/Ds digitize the I + Q signals synchronously- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1 & 2) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
MS-M 26-Pin RF Cable Assembly 0.5m
40-979-526-0.5m-FU
RF Cable Assembly
The MS-M RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
75 Ohm 1.6/5.6 to 1.6/5.6 Cable Assembly
40-977-791-0.1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
RF ATE Tester
ADIVIC MP5800/MP5806
-
MP5800 seamlessly upgrades your existing Chroma 3380, 3650 to RF ready ATE test solution, user friendly debug tools, IOT turnkey test solution.
