RF Wattmeters
Measure RF power.
-
Product
RF Down-Converter
CDCM100A-2
-
Systems Engineering & Management Company
The CDCM100A Series Down-Converter is an IP-67 rated device designed for installation on antenna pedestals. It is a pressurized, water-proof module designed for use with antennas that have a Tri-Band Feed. The CDCMA100 Series Down-Converter is a block down-converter supporting 1415-1585 MHz, 1650-1850 MHz, 2185-2485 MHz and 4400-5250 MHz, down-converting 4400-5250 MHz to 300-1150 MHz.
-
Product
RF Filters
-
Smiths Interconnect is committed to providing technically advanced, high quality “state-of-the-art” RF Filters, Multiplexers, Switched Filter Banks, and Integrated assemblies, from 100 KHz to 65 GHz. All products are subject to the same rigorous design, manufacturing, and inspection criteria. Regardless of the application, our internal process and procedures help ensure that all products are fully compliant to all specifications. Our R & D activities are constantly evaluating new materials, plating techniques, and manufacturing processes to offer the highest performing components available today.
-
Product
RF Power Limiters
-
A protective electronic circuit that clamps or attenuates high-power Radio Frequency (RF) signals to prevent them from damaging sensitive components like Low Noise Amplifiers (LNAs) in receiver front-ends.
-
Product
RF Digitizer With 6.5 GHz Bandwidth
ADQ7WB
Digitizer
ADQ7WB is an RF digitizer with an analog input bandwidth of 6.5 GHz. It supports highly linear wideband data capture, and utilize Teledyne SP Devices' proprietary ADX technology in order to ensure industry-leading spurious-free dynamic range (SFDR).
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
RF Power Transistors
Silicon Bipolar
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a broad range of silicon bipolar transistor products designed for applications ranging from DC to 3.5 GHz. Our silicon bipolar transistors are ideal for civil avionics, communications, networks, radar, and industrial, scientific, and medical applications. Our all-gold metallization fabrication processes ensure high performance and long term reliability for ground and space applications.
-
Product
RF Synthesizer
-
Low phase noise broadband RF synthesizer module with extremely low step size and USB control.
-
Product
Real-time RF Channels Simulator
RF-LiveSim
-
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
Product
RF Terminators
-
Typically placed at the end of a transmission line and is designed to match the cable's AC impedance.
-
Product
RF Coaxial Probes & Probe Positioner
-
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
Product
RF Signal/Wireless Camera/Mobile/Bug Detector
SH-055U8 / 01018
-
The RF Signal Detector / Wireless Camera Detector / Mobile Phone Detector / Bug Detector applies digit (numeric) display to show the sensitivity level. With up and down buttons, user knows the sensitivity setting directly
-
Product
RF Signal Generators
-
Value for money RF signal generators with frequency capability from 1.0GHz up to 6.0GHz.
-
Product
RF Semi-Rigid Cable Assemblies
-
The Semi-Rigid cables are available with a copper or aluminum jacket and available with a selection of different platings and 4 different diameters (.047", .085", .141" & .250"). The Conformable®, or Hand-Formable (BJ - Braided Jacket), has a tin filled braid with a metal foil underlay and is also available in the same diameters as the Semi-Rigid type . The Flexible version, our Mini-Flex, has an FEP jacket, round braid and inner spiral shields and is available in 2 diameters, .105" &.165". All 3 types (Semi-Rigid, Conformable & Mini-Flex) are manufactured using the same type dielectric core and have virtually the same electrical performance. The decision of which cable to use should be primarily based upon your application.
-
Product
RF Instrumentation
-
Our electronic products are custom-designed for fast and accurate data acquisition so you can make the most out of your range time. Optimized with the rest of our product line, you get a best-in-class measurement system backed by our longstanding reputation of high quality and unsurpassed performance. Our electronic products are also compatible with prior generation NSI-MI Technologies' instrumentation and also with many third party instruments.
-
Product
RF Safe Stop
-
We have extensive experience in the design and manufacturing of technologies relating to engine stopping; this includes highpower RF and microwave devices as well as the associated subsystems that are assembled to provide a self-contained unit.RF Safe-StopTM, the ultimate in target deactivation technology from Teledyne e2v a leading global provider of innovative technology for high performance systems and equipment is a state-of-the-art, non-contact jamming system. The system is capable of bringing moving targets across land, sea and air to a controlled stop at a safe distance without collateral damage. The technology has been successfully trialled on Unmanned Aerial Vehicles, boats, cars, motorbikes and commercial vehicles.
-
Product
PXI RF Matrix Switch Module
Matrix Switch Module
PXI RF Matrix Switch Modules are organized into rows and columns and provide maximum flexibility for switching systems by allowing you to connect any channel to any other channel. PXI RF Matrix Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a matrix that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
Product
RF And Microwave Accessory Kit
N9311X
-
N9311X RF and Microwave Accessory Kit complements Keysight's low-cost handheld and benchtop solutions. These accessories provide you with a complete solution when using Keysight handheld and low-cost benchtop solutions for your measurement needs.
-
-
Product
RF Volt Meters
-
The latest addition to Boonton’s popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range.
-
Product
Wattchman RF Station Monitor/Alarm Systems
81080 Series
-
The Coaxial Dynamics Wattchman Monitor/Alarm measures forward and reflected RF power simultaneously in 50-Ohm coaxial cables and transmission lines. It is compatible with our entire series of 7/8" through 6-1/8" Line Sections and will accept plug-in elements that range from 5 watts to 100 kW full scale from 0.45 MHz to 2300 MHz.
-
Product
RF Safety Monitoring
MVG EME Guard XS 40GHz
-
EME Guard XS 40 GHz has been specifically designed to cover the new 5G millimeter wave bands. This RF safety tool is important for keeping those working close to RF emitters safer. It is easy to use, continuously scanning electromagnetic waves, and alerts the user when acceptable pre-selected limits have been exceeded.
-
Product
50 Ohm MMCX to MMCX Cable Assembly
40-977-571-0.1m
RF Cable Assembly
This 0.1m long MMCX cable assembly is part of the range of RF cables. Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
RF Switch
-
RF switches are components used for switching the signal paths of high frequency circuits in wireless communication devices.
-
Product
RF Cable Assemblies
-
Radiall's extensive range of RF cable assemblies features outstanding electrical performance, low loss and high frequency. The range includes flexible, semi-rigid, corrugated and hand-formable cable assemblies with a combination of RF cables and connectors optimized for each market or application. Custom RF cable assemblies are also available.
-
Product
MS-M RF Connectors for Pickering
-
The connectors below are suitable to use with Pickering cards and modules that utilize a MS-M RF connector.
-
Product
RF Shielded Test Enclosure, Low Profile
JRE 2214
-
Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan. Tough 'honeycomb' vent maintains shielding effectiveness throughout the full frequency range. Optional fan is available for additional airflow.
-
Product
High Bit-depth RF Record & Playback System
GSS6450
-
The Spirent GSS6450 offers the flexibility, control and high dynamic range required to test the most challenging applications.
-
Product
RF Signal Detector
H-055DRV / 01019
-
The RF Signal Detector / 2G Cellular Phone Detector / Wireless Camera Detector / Bug Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices.
-
Product
RF Over IP
-
Quintech Electronics and Communications Inc.
Digital IF / RF Over IP Solutions.
-
Product
RF Milliwatt Meters
Type NDB-2 and NDB-3
-
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
