Switches
enable on off function or change of direction.
See Also: Membrane Switch, Coaxial Switches, Crossbar, High Voltage Switching, Fiber Optic Switching, Microwave Switching, Optical Switch
-
Product
PXI 10xSPST 16A Power EMR Module
40-161-003
-
These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
PXI/PXIe High Density 2A Multiplexer, 8-Bank, 8-Channel, 2-Pole
40-614D-004
-
The 40-614D-004 (PXI) and 42-614D-004 (PXIe) 8-bank, 8-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI Differential Fault Insertion Switch Modules
-
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
Product
PXI 8 Slot BRIC 528x4 2-pole (12 sub-cards)
40-562A-122-528X4
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
-
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
Haptic testing
-
Haptic tests are becoming ever more important owing to the increasing and sector-independent popularity of switches and buttons in diverse products. More and more customers, especially in the automobile sector, attach great value to good haptic performance by their control elements. A precise switching feeling, low friction of the moving elements, backlash-free execution both in the rest position and during operation are only some of the criteria for good haptic switching characteristics.
-
Product
Precision Programmable AC and DC Sources, 0 - 333VAC, 0 - 3,000A / Phase, 15kVA - 1.08MVA
Tahoe Series
-
AMETEK Programmable Power, Inc.
The California Instruments Tahoe Series combines intelligence and flexibility with high power to create an advanced platform of AC solutions. Using a state-of-the art SiC power switching architecture and Digital Signal Processing, the Tahoe Series combines a robust, high-power AC/DC source with an advanced power analyzer in a single floor standing chassis.
-
Product
PXI Solid State Very High Density Matrix
40-501-001
-
The 40-501 is a very high density matrix using solid state switching configured as a 64x4 1-pole matrix in a single slot 3U PXI module. It is ideal for applications requiring fast operation and a long service life with frequent switch operations at high voltages. Since the design is based on solid state relays the matrix has no wear out mechanism.
-
Product
Oil Test System
-
The Oil Test system Model OTS 2K1 is portable transformer oil Test system. It is a specially designed for accurate measurement of Loss Factor, Permitivity & Volume Resistivity Measurement of Transformer Oils & Petroleum jellys. The test frequency is 50 Hz . The system is provided with Mode Selector Switch so that once the oil cell is connected, it can measure all Three parameters in different modes without handling the test leads.
-
Product
Modular Multilevel Converter (MMC) Test Bench
-
Research into innovative HVDC interconnections and FACTS applications requires a flexible hardware architecture that allows testing of new topologies and switch configurations.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 1 Amp, 1m, 500 Port
A500RMR-F-1B100
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.
-
Product
PXI 32 x SPDT Reed Relay
40-110-121
-
Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
Alternate 1.10 (31.18) - 7.20 (204.00) Switch Probe
TSP100-C100-2
-
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI 8-Slot BRIC Matrix, 2A 2-Pole 330x4, 6 Sub-cards
40-566B-106
-
The 40-566B-106 is a 330x4 matrix with 2-pole switching and is part of a range of high-density large PXI matrix modules with the ability to switch up to 2 Amps or 300VDC/150VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
Product
USB-C® Short Channel Rx Precet. Test Fixture
AUT20098
-
*Easy swap between CC1 and CC2RP & RD Mode: In the older version of the USB-C full breakout board, users had to manually set the jumper with a short pin. But now users can easily swap between the two by just moving the switch.*In the previous version, the soldering joint of Test Fixture Host Fixture 1A gets worn out quickly from repetitive plug and pull. This newly designed fixture is more durable and users can easily replace the worn out SMA connectors with new ones.*DC-in Jack is upgraded to +5V USB C portA boost in user experience as it makes setting up easier.
-
Product
PXI 12-Slot BRIC Matrix, 66x16 2-Pole (6 sub-cards)
40-562B-322-66X16
-
The 40-562B-322-66X16 is a high density BRIC12 matrix module with a size of 66x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-0.5m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 2m, 250 Port
A500RMR-C-5C200
-
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
PXI 6U Power Relay Module
-
The SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC. The module is built on a single width 6U PXI module and the interface is via a standard PXI/CompactPCI backplane. Connection to the switching contacts is via three 50-pin D-type male connectors mounted on the front panel. These are machined contact types with 7.5A current carrying capacity.
-
Product
LXI Microwave Multiplexer, SP6T, 11-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-711
-
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
PXI-2530B, 128-Channel, 1-, 2-, or 4-Wire PXI Multiplexer Switch Module
778572-30
-
128-Channel, 1-, 2-, or 4-Wire PXI Multiplexer Switch Module—The PXI‑2530B is a high-density, multiconfiguration reed-relay switch. With four multiplexer and three matrix configurations, the PXI‑2530B is an excellent solution for complex or high‑channel‑count systems. Multiplexer configurations include 128x1 (1‑wire), 64x1 (2‑wire), 32x1 (4‑wire), or eight banks of 16x1 (1‑wire). Matrix configurations include 4x32 (1‑wire), 8x16 (1‑wire), or 4x16 (2‑wire). You can implement these configurations by selecting the appropriate terminal block.
-
Product
LED Drivers led Switching Power Supply
-
Dongguan Longwei Electronic Technology Co., Ltd.
LED drivers led switching power supply
-
Product
PXI 4 Slot BRIC 88x8 2-Pole (4 sub-cards)
40-562A-022-88X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI High Voltage Multiplexer, 24-Channel
40-320A-101
-
The 40-320A-101 is a single 24-channel MUX and is part of our 40-310/320A range of High Voltage Switching Modules which will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320A) configurations.
-
Product
AXIe Switch Module
PK100x4
-
The PK100x4 AXIe module implements a 100x4 matrix switcher structure (100 inputs – 4 outputs). The module is designed to work in functional control systems, systems for monitoring and diagnostics of ground-based electronic equipment, control systems for bench tests.
-
Product
PXI 4 Slot BRIC 22x16 1-Pole (2 sub-cards)
40-562A-021-22X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
MCX Male to MCX Male Cable, 50 Ohm, 1 m
188374-01
-
The MCX-MCX Coaxial Cable is used for modular instruments such as PXI switches. This cable is available in 1 m, 30 cm and 15 cm lengths.
-
Product
Cable Assembly, Receiver, 36", Micro Power to 41-Pin FML Power Connector, for VTI EX1200-2001 Switch Module
540249010247
-
CBA, RCV, MicroPWR to 41-Pin J1 PWR Conn f/VTI EX1200-2001 Switch Module.
-
Product
Antenna, Biconica-log
EM-6917C-1 | 26 MHz – 1 GHz
-
The EM-6917C-1, a hybrid combination of the industry standard biconical and log periodic antennas, delivers an unmatched combination of frequency coverage and high power handling capability. Featuring exceptionally broad frequency coverage of 26 MHz to 1 GHz, the EM-6917C-1 eliminates the need for adjustments or switching antennas in most test applications up to 1 GHz, and it does so without compromising power handling capability for transmit applications.
-
Product
Wire Systems Analyzer
Console Test Systems (CTS)
-
Wire Systems Analyzer Commercial Roll around detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex. Used to verify the operation of relays, circuit breakers, indicators, switches, diodes, transformers, 1553 couplers, etc.
