I2C
IC serial bus protocol speed grades; standard mode: 0.1 / 0.4, fast mode: 1.0 / 3.4 / 5.0 Mbit/s are maximum ratings. Also known as: Inter-Integrated Circuit
See Also: Serial, Serial Communications, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
PICkit Serial Analyzer
DV164122
-
The PICkit Serial Analyzer is a low-cost USB-based tool used to direct communication between a PC and an external serial device. I2C™ - Master, I2C™ - Slave, SPI - Master, USART – Asynchronous, USART – Synchronous, LIN (external hardware required to meet electrical specifications), MICROWIRE.
-
Product
SparkFun MicroMod Environmental Function Board
-
The SparkFun MicroMod Environmental Function Board adds additional sensing options to the MicroMod Processor Boards. This Function Board includes three sensors to monitor air quality (SGP40), humidity & temperature (SHTC3), and CO2 concentrations (STC31) in your indoor environment. To make it even easier to use, all communication is over the MicroMod's I2C bus!
-
Product
RX Family Of 32-bit High Power Efficiency MCUs
RX700
-
The RX700 Series is the flagship of the RX Family with outstanding performance at up to 240MHz CPU performance, power efficiency, and connectivity. It offers up to 4MB of embedded flash memory, integrates rich peripherals such as Ethernet, USB, CAN, I2C, SSI and HMI function. The RX700 Series is an ideal fir for high end application in industry, office automation and other areas, where performance really matters.
-
Product
Small outline PCB with 72 Pin Socket
1091-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
12C Adapter Slave
I2C RS232 adapter
-
RS model:*RS232 controlledASCII commands via the serial interfaceI2C bus transparent, 1: 1 transmission IC model:*I2C controlledcommands via the I2C busSerial interface is transparent. 1: 1 transfer
-
Product
Negative Tester
I2C
-
telos EDV Systementwicklung GmbH
The most common use of an I2C interface is to send and receive data in compliance with the I2C specification. This implies that the device we are talking to is known to conform to the I2C standard, as well.
-
Product
SparkFun Photodetector Breakout
MAX30101 (Qwiic)
-
The SparkFun Photodetector Breakout is an updated version of the SparkFun Particle Sensor Breakout includes the MAX30101, a highly sensitive optical sensor and successor to the MAX30105 and MAX30102. The MAX30101 Breakout utilizes a photon detector to measure the amount of returning light that is reflected back from the LEDs. This is useful for various applications like particle (i.e. smoke) detection, proximity measurements, and even photoplethysmography. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
Product
SIMRC - 8 x 2 Matrix 2-Pole
1030-R-8-2-2-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
SparkFun High Precision Temperature Sensor
TMP117 (Qwiic)
-
The SparkFun Qwiic TMP117 breakout is a high precision temperature sensor equipped with an I2C interface. It outputs temperature readings with high precision of ±0.1°C across the temperature range of -20°C to +50°Cs with no calibration and a maximum range from -55°C to 150°C. The SparkFun High Precision Temperature Sensor also has a very low power consumption rate which minimizes the impact of self-heating on measurement accuracy. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Garmin LIDAR-Lite V4 LED
Distance Measurement Sensor (Qwiic)
-
The LIDAR-Lite v4 Qwiic from GARMIN is a high-performance, wireless optical distance measurement sensor that doesn't require any soldering to get started. This is the ideal solution for drone, robot, IoT, or unmanned vehicle operations when space is tight and power is limited. This sensor has up to a 10 meter range, 1cm resolution, and requires 85mA during data acquisition. The user can read and write to the LIDAR-Lite v4 using the I2C protocol; this is where the addition of the SparkFun Qwiic system really shines. The LIDAR sensor requires 5V to operate but runs on 3V3 logic. With a 5V boost circuit and an easy-to-use Qwiic connector you can power the sensor and get distance measurements over Qwiic all with a single piece of hardware.
-
Product
Serial EEPROM
-
STMicroelectronics is the world's #1 supplier of Serial EEPROM thanks to development of leading-edge technology, recognized product robustness and high manufacturing capacity. ST focuses on the availability of the complete portfolio with short lead times, high flexibility in volume and worldwide distribution through selected partners. ST's comprehensive portfolio offers reliable SPI, I2C and Microwire products in SO8N, TSSOP8, DFN2X3, DFN5, WLCSP and bare die packages.
-
Product
COM Express Type 10 Mini Module With Intel® Atom® X5 And X7 Processor
CEM310
-
The CEM310, a COM Express Type 10 Mini module, supports Intel® Atom® x5 and x7 processors (codename: Apollo Lake) in a board size of 84mm x 55mm. It has 8GB of DDR3L onboard memory and an optional 64GB eMMC memory. The Intel® Atom®-based COM Express Type 10 Mini module comes with a variety of I/O and expansion options including four PCIe x1 lanes, one Gigabit LAN port with Intel® i210IT Ethernet controller, two USB 3.0, eight USB 2.0, two SATA-600, four digital I/O channels, HD Codec audio, one DDI, one LVDS, one LPC, one SPI, two serial TX/RX and one I2C to meet customer requirements. Aside from the rich I/O options, the CEM310 has a wide voltage input range of 4.75V to 20V to meet the varying voltage input requirements for automotive or transportation applications. In addition, it supports an extended operating temperature range from -20ºC to +70ºC or optional -40ºC to +85ºC to ensure stable and reliable operation in harsh environments. The CEM310 supports watchdog timer, hardware monitoring functions, SMBus as well as smart battery (optional).
-
Product
SparkFun Digital Temperature Sensor Breakout
AS6212 (Qwiic)
-
This SparkFun Qwiic Digital Temperature Sensor Breakout provides a combination of high temperature accuracy with excellent low power consumption using the AS6212 digital temperature sensor from ams AG. The sensor measures temperature data up to ±0.2°C; accuracy over a wide range (-40°C; to +125°C;) and consumes an average of 6µA in normal operation (0.1µA in standby). The AS6212 communicates via I2C and has eight available I2C addresses selected by a pair of solder jumpers on the board. The breakout routes the I2C interface to a pair of Qwiic connectors to work with our plug-and-play Qwiic Ecosystem but also routes the bus and other pins to a standard 0.1"-spaced PTH header for users who prefer a soldered connection.
-
Product
Mezzanine System
3560
System
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
Product
Open Standard Module (OSM)
ROM-2620
-
Advantech ROM-2620 OSM 1.1 Computer-on-Module is powered by NXP i.MX 8ULP SoC which includes up to 2 Arm Cortex-A35 cores in combination with one Cortex-M33 real timeprocessor and Vivante GC7000 nanoULTRA/GC328 graphics engine. It provides USB2.0, Fast Ethernet, MIPI-CSI, I2C, SPI, GPIO, PWM and MIPI DSI display for embedded applications
-
Product
Logic Analyzer
LAP-16064U
-
Zeroplus Technology Corperation
Sample rate (Internal clock): 100MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Channels may be selectively defulted to /Channels: 16 CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals. Glitch Capture Capability: 5ns. Bandwidth: 75MHz.
-
Product
Multi-protocol USB Type-C Analyzer
Type-C Tracker
-
Protocol and Electrical Analysis Tool for Type-C Communications Standards. All-in-One: Concurrent and tightly synchronized capture of USB Power Delivery protocol, Type-C voltage tracking (Vconn, Vbus, SBU, and CC), USB 2.0, Thunderbolt 3 UART and DisplayPort auxiliary (AUX) signaling over the Type-C SBU lines, alternate (ALT) mode support for DisplayPort, HDMI, and Thunderbolt, and capture and decoding of Serial Wire Debug (SWD) protocol, UART, Serial Peripheral Interface (SPI) I2C vendor-specific protocols, and Type-C Port Controller Interface traffic over I2C.
-
Product
SparkFun Pressure Sensor Breakout
MS5803-14BA
-
This is the MS5803-14BA Pressure Sensor Breakout, a high resolution pressure sensor with both an I2C and SPI interface. This MEMS pressure sensor measures the absolute pressure of the fluid around it which includes air, water, and anything else that acts like a viscous fluid. Depending on how you interpret the data, you can determine altitude, water depth, or any other tasks that require an accurate pressure reading. What makes the MS5803-14BA unique is the the gel membrane and antimagnetic stainless steel cap that protects against 30 bar water pressure.
-
Product
USB Protocol Analyzers
Beagle Series
-
Our line of Beagle Protocol Analyzers provide real-time visibility into I2C, SPI, and USB systems making them ideal tools for embedded engineers.The Beagle analyzers provide high-performance bus monitoring in a small, portable package that includes cross-platform software support making it perfect for engineers in the field and in the lab.
-
Product
SparkFun Human Presence Sensor Breakout
AK9753 (Qwiic)
-
This is not your normal Passive Infrared (PIR) sensor! The SparkFun AK9753 Human Presence Sensor Breakout is a Qwiic-enabled, 4-channel Nondispersive Infrared (NDIR) sensor. Each channel has a different field of view, so not only can the AK9753 detect a human, but it can also tell which direction the person is moving. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
Product
SparkFun Triple Axis Digital Accelerometer Breakout
ADXL313 (Qwiic)
-
The SparkFun ADXL313 Breakout is a low power, high resolution (up to 13-bits) 3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Digital output data is formatted as 16-bit two's complement and is accessible through the on-board Qwiic connectors (I2C) or SPI.
-
Product
SparkFun Distance Sensor Breakout
4 Meter, VL53L1X (Qwiic)
-
This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X from STMicroelectronics uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the reflection to the target. That means that you will be able to measure the distance to an object from 40mm to 4m away with millimeter resolution! To make it even easier to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system so no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1”-spaced pins in case you prefer to use a breadboard.
-
Product
1584W to 2500W - Single Output
HFE Series
-
*1U rackmount containing up to 5 units*Up to 29.2W/in³ power density*Internal ORing MOSFET & Current Share*High Efficiency*Up to 9,500W in 1U rack*PMBus™(I2C) and LAN options
-
Product
Smart Card Reader
UTC-100P-S
Card Reader
International Standard: Comply with PC/SC 1.0 standard and EMV L1. CPU Card: Comply with ISO7816-1,2,3,T=1 and T=0 protocol. Memory Card: Synchronous 2-line, 3-line and I2C interface.
-
Product
Alchitry Au FPGA Development Board (Xilinx Artix 7)
-
The Alchitry Au is the "gold" standard for FPGA development boards and it's possibly one of the strongest boards of its type on the market. FPGAs, or Field-Programmable Gate Arrays, are an advanced development board type for engineers and hobbyists alike to experience the next step in programming with electronics. The Au continues the trend of more affordable and increasingly powerful FPGA boards arriving each year. This board is a fantastic starting point into the world of FPGAs and the heart of your next project. Finally, now that this board is built by SparkFun, we added a Qwiic connector for easy I2C integration!
-
Product
I2C High Speed Interface for USB
telos Tracii XL
-
telos EDV Systementwicklung GmbH
Tracii XL is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 2 Mbit/s. Additionally Tracii XL can work as an I2C monitor.
-
Product
SparkFun Distance Sensor
1.3 Meter, VL53L4CD (Qwiic)
-
This SparkFun Distance Sensor Breakout utilizes the VL53L4CD next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at short ranges for its size. The VL53L4CD from STMicroelectronics uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an infrared laser to time the reflection to the target. That means that you will be able to measure the distance to an object from 1mm to 1300mm away with millimeter resolution! To make it even easier to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system so no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1”-spaced pins in case you prefer to use a breadboard.
-
Product
SparkFun Pulse Oximeter And Heart Rate Sensor
MAX30101 & MAX32664 (Qwiic)
-
The SparkFun Pulse Oximeter and Heart Rate Sensor is an I2C based biometric sensor, utilizing two chips from Maxim Integrated: the MAX32664 Biometric Sensor Hub and the MAX30101 Pulse Oximetry and Heart Rate Module. While the latter does all the sensing, the former is an incredibly small and fast Cortex M4 processor that handles all of the algorithmic calculations, digital filtering, pressure/position compensation, advanced R-wave detection, and automatic gain control. We've provided a Qwiic connector to easily connect to the I2C data lines but you will also need to connect to two additional lines. This board is very small, measuring at 1in x 0.5in (25.4mm x 12.7mm), which means it will fit nicely on your finger without all the bulk.
-
Product
Single-Supply Voltage Output D/A Converters
-
Analog Devices offers the broadest portfolio of low voltage single-supply D/A converters (DACs) in the industry, which includes many leading products in performance and package size. A wide variety of applications use ADI precision nanoDAC® products because of their small footprint and robust range of features, including 8- to 16-bit resolution, low power, a fast 50 MHz SPI or 3.4 MHz I2C interface, and more, in a tiny package option. ADI’s nanoDAC+™ products offer enhanced features such as higher accuracy, improved dc performance, increased robustness, and lower glitch energy, among other advantages.
-
Product
Silicon Oscillators
-
Analog Devices silicon oscillators are frequency programmable via pin-strapping, or through the resistor connection or serial interface (SPI or I2C). These solid-state clocks are well-suited for general-purpose usage, such as PGAs, ASICS, microprocessors, or UARTS, and they operate from 1 kHz to 170 MHz. Silicon oscillators are also ideal switching regulator clocks as they provide synchronization and EMI reduction (via spread spectrum).
