I2C
IC serial bus protocol speed grades; standard mode: 0.1 / 0.4, fast mode: 1.0 / 3.4 / 5.0 Mbit/s are maximum ratings. Also known as: Inter-Integrated Circuit
See Also: Serial, Serial Communications, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
TTL/I2C/SPI Expansion Kit
OP-SB85L
-
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
-
Product
SparkFun Qwiic Micro:bit Breakout (with Headers)
-
The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. We've already attached headers to this version of the board so you don't need to worry about any soldering! This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other Qwiic sensors, motors, LEDs and more!
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
SparkFun GPS Breakout
NEO-M9N, U.FL (Qwiic)
-
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
SparkFun GPS Breakout
NEO-M9N, SMA (Qwiic)
-
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options including SMA. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions increasing, precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which makes it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
I2C Bus Monitor - USB
Model JI-216
-
The JI-216 I2C Bus Monitor is a low cost, easy-to-use PC hosted instrument specificallydesigned for troubleshooting and debugging I2C networks. The JI-216''s FPGA basedarchitecture provides for the capture and display of all valid or invalid messages and I2Cbus events. Captured I2C messages are available for display in two modes: real-timestreaming, or triggered. These modes provide optimized data display for either hardwareor software development. The SDA/SCL timing display aids in tracking down and solvinghardware timing problems. JI-216''s broad bandwidth (DC 3.4Mbits/s), wide input signalrange (0 15.0V), and variable signal filtering provides flexibility in monitoring a variety ofI2C bus systems. An intuitive Windows application manages instrument setup andcontrol. Communications and unit power is provided via a USB 2.0 link.
-
Product
Clock and Data Recovery/Retiming
-
Analog Devices provides single rate, multiple rate, and continuous tuning clock and data recovery (CDR) ICs for metro, long haul, DWDM, FSO, instrumentation, and other applications. Our any rate CDR ICs allow easy integration into protocol agnostic applications, automatically locking onto incoming data streams at any rate, from 10 Mbps to 2.7 Gbps or from 6.5 Mbps to 11.3 Gbps, without the aid of a reference clock while reporting the acquired data rate over the I2C interface. With a proprietary dual loop design, our any rate CDR ICs feature fast locking with superior jitter performance.
-
Product
SparkFun Humidity And Temperature Sensor Breakout
Si7021
-
The Si7021 is a low-cost, easy-to-use, highly accurate, digital humidity and temperature sensor. This sensor is ideal for environmental sensing and data logging and perfect for build a weather stations or humidor control system. All you need are two lines for I2C communication, and you’ll have relative humidity readings and very accurate temperature readings as a bonus!
-
Product
DC/AC Sine Inverter
44KS6
Sine Inverter
- +28 VDC- Output 26 VAC @ 400Hz- 75 VA output power- MIL-1275D Compliant- Reverse Polarity Protection- Continuous Background Built-In-Test (BIT)- IPMI Monitoring of Voltages, Currents and Temperature- I2C communication- Temperature monitor- Nuclear Event Input
-
Product
Grid-EYE High Performance Type
-
Panasonic Industrial Devices Sales Company of America
Panasonic's Grid-EYE® Series High-Performance Type is an 8x8 (64) pixel Infrared Array Sensor. This Sensor offers digital output (I2C) for thermal presence, direction, and temperature values. The built-in lens includes a 60-degree viewing angle. The Grid-EYE Sensor features compact SMD design using MEMS thermopile technology. This Sensor offers several advancements over the original Grid-EYE, including higher accuracy, enhanced resolution, and longer detection distance for true next-generation performance.
-
Product
InfiniiVision Oscilloscopes
2000 X-Series
-
70 MHz to 200 MHz See more signal detail with 50,000 wfms/s update rateView time-correlated digital content with 8 digital channels (MSO)Modulate signals within the scope with WaveGen, built-in 20 MHz function generator (optional)Quickly characterize signals with the built-in 3-digit voltmeter and 5-digit counter option Decode serial busses faster with hardware-based serial analysis options for CAN, LIN, I2C, SPI and RS232/422/485/UART Protect your investment with full upgradability
-
Product
Bus Analyzer, Monitor, Debugger & Programmer
BusPro-I™
-
The BusPro-I has all the power, flexibility, and features you need to monitor and debug the I2C bus circuitry on your board. The BusPro I2C can be used to monitor and log I2C bus traffic in real-time, generate I2C transactions to communicate with peripheral components on the bus, and in-system program I2C compatible EEPROMs.
-
Product
Qwiic Pressure/Humidity/Temp (PHT) Sensor - MS8607
-
The MS8607 from TE is an impressive combination pressure, humidity, temperature (PHT) sensor with accuracy of ±2mbar pressure, ±3% humidity, and ±1°C. Perfect for sensing general weather conditions the MS8607 really shines for high altitude, low pressure applications. Capable of sensing down to 10mbar, this pressure sensor separates itself from many other I2C pressure sensors like the BME280. The MS8607 is simple to use and gives the user some very powerful readings with very little power and conversion time.
-
Product
Soil Moisture Sensor
Modbus RS485
-
This is a contact-less capacitive soil moisture sensor, a continuation of my I2C soil moisture sensor. This particular version of the sensor is suited for more professional installations where long cable runs is a requirement. It adds a local voltage regulator to mitigate the voltage drop and RS485 transceiver to accommodate long wires, also reverse polarity and an additional ESD protection level is added.
-
Product
Interface
-
Renesas offers industry-leading devices to enable efficient and reliable communication for industrial control, networking and computing applications. Dual protocol transceivers, voltage level translators, I2C Buffers, wide operating voltage range RS-232 transceivers, and RS-485/422 devices with the highest noise immunity and ESD protection in small packages are available to support high-speed data transfer and a variety of configurations to fit your applications.
-
Product
Logic Analyzer
LAP-16064U
-
Zeroplus Technology Corperation
Sample rate (Internal clock): 100MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Channels may be selectively defulted to /Channels: 16 CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals. Glitch Capture Capability: 5ns. Bandwidth: 75MHz.
-
Product
SIMRC - 16-Channel 2-Pole Multiplexer
1020-R-16-2-5/1D
Multiplexer Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
LCD Controllers
CP240x
-
The CP240x extremely low power LCD controller devices can drive up to 128 LCD segments. These devices are easily interfaced with any microcontroller using SPI or I2C interfaces. A benefit to this approach is designers can select the best-fit MCU for the system and then add the CP240x to handle LCD requirements efficiently with respect to system size and power consumption.
-
Product
I2C High Speed Interface for USB
telos Tracii XL
-
telos EDV Systementwicklung GmbH
Tracii XL is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 2 Mbit/s. Additionally Tracii XL can work as an I2C monitor.
-
Product
SIMRC - 8 x 2 Matrix 2-Pole
1030-R-8-2-2-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
SIMRC - 16-Channel 1-Pole Multiplexer
1020-R-16-1-5/1D
Multiplexer Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
I2C Soil Moisture Sensor
-
Capacitive soil moisture sensor interfaced via I2C. Additionaly provides ambient light and temperature readings. Open Source Hardware. Soil moisture sensing, Light sensing, Temperature sensing.
-
Product
720W to 1000W - Single Output
CPFE1000FI Series
-
*Smaller size than CPFE1000F*Baseplate cooled, no fan required*Protective coating option*I2C Interface*High Efficiency
-
Product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, SPI, I2C, 2 LANs And DIO (2-in/1-out)
IFB125
-
The IFB125 is powered by the low-power Freescale i.MX6UL processor in the ARM® Cortex™-A7 micro architecture. It supports extended operating temperature ranging from -40°C to 70°C, and can withstand vibration up to 5G. Its flexible wide voltage range 9V - 48V DC power input with a lockable terminal block type connector also enhances its reliability in harsh environments. To meet most of Industrial IoT needs, the IFB125 supports multiple communication interfaces for maximum flexibility, including LAN, serial, USB, and digital I/O ports. The Industrial IoT gateway has 256MB onboard memory that features data transfer rates of DDR3-1600, as well as 4GB eMMC flash memory onboard for storage. This embedded IoT gateway platform is equipped with one PCI Express Mini Card slot and one SIM card slot. Additionally, it supports DB9 connectors with both SPI and I2C function as communication protocols to suit for specific applications
-
Product
Channelized Down-Converter
DCV Series 5” x 2.5” x 0.6”
-
*Connectorized Package *Wide Choice of Frequency Ranges *Integrated Filters *Gain Control *L-Band to 70 MHz IF Range Available *L-Band to 140 MHz IF Range Available *CAN, RS-232, I2C, or SPI Control *Internal / External References *Custom Designs Available *Low Power Consumption *Low Phase Noise *Low Spurs
-
Product
SIMRC - 16 x Uncommitted Reed Relay, SPST
1010-R-16-1-5/1D
Reed Relay
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
SparkFun Digital Temperature Sensor Breakout
TMP102
-
The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some temperature sensors use an analog voltage to represent the temperature, the TMP102 uses the I2C bus of the Arduino to communicate the temperature. Needless to say, this is a very handy sensor that doesn't require much setup.
-
Product
SparkFun MicroMod Environmental Function Board
-
The SparkFun MicroMod Environmental Function Board adds additional sensing options to the MicroMod Processor Boards. This Function Board includes three sensors to monitor air quality (SGP40), humidity & temperature (SHTC3), and CO2 concentrations (STC31) in your indoor environment. To make it even easier to use, all communication is over the MicroMod's I2C bus!
-
Product
SparkFun Spectral Sensor Breakout
AS7262 Visible (Qwiic)
-
The SparkFun AS7262 Visible Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7262 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board --- simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic Shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
-
Product
Gyroscope Module 3-Axis L3G4200D
27911
-
The Gyroscope Module 3-Axis L3G4200D provides raw angular rate and temperature data measurements that are accessed from the selectable digital I2C or SPI interface. The small package design and SIP interface accompanied by the mounting hole make the sensor easy to integrate into your projects. Designed to be used with a variety of microcontrollers, the module has a large operating voltage window.
