Instrumentation
See Also: Measurement, Metrology, Instrumentation Amplifiers
-
Product
Power Electronics Test Solutions
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
Infrared Linescanners
-
Fluke Process Instruments Linescanners are designed for continuous monitoring of parts or processes. The up to 300Hz scan speed is the fastest in the business. This provides more complete data about even the highest speed manufacturing processes. With up to 1024 data points per scan and up to 200:1 optics, each spot on the target surface is over sampled up to three times, providing complete coverage.
-
Product
Generic RF ATE Test
-
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
-
Product
Quad Op-Amp Loop
QOAL400
-
The QOAL400 module is a precision instrument capable of measuring all common parameters of an Op Amp, including AC as well as DC parameters. The QOAL400 has four completely independent channels, which allow a quad device to be tested in a minimum amount of time. Each channel has a full set of resources to measure all common parameters.
-
Product
Ion & Electron Detection
-
Photonis is the global leader in the development and manufacturing of detectors and optical components to detect ions and electrons. These detectors and components have been designed for a wide range of scientific instruments used in space and research projects but also in cells and material analysis in lifescience or non destructive testing.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 2 Channels, 1.5 GHz Bandwidth
DN2.223-02
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
PXI-2565, 16-Channel, 7 A, SPST PXI Relay Module
777754-01
Relay
16-Channel, 7 A, SPST PXI Relay Module—The PXI‑2565 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It delivers high-current switching of DC power supplies, AC line power, and AC/DC current sources. The PXI‑2565 is fully software programmable and supports multiple instrument synchronization.
-
Product
10A DIGITAL MICRO-OHMMETER
MPK-2000e
-
The MPK-2000e digital very low resistance ohmmeter is a portable, microprocessor controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10A. It uses the Kelvin-type, four-terminals measurement principle, thus eliminating errors caused by lead and contact resistances.
-
Product
Precision LCR Meter (20Hz to 1MHz)
ST2827
-
ST2827 series precision LCR meter has multiple functions and higher test frequency. With small size and portable appearance, it is convenient for use on the shelves. This instrument has a basic accuracy of 0.05%, maximum test frequency of 1MHz and resolution of 10 mHz. ST2827 series is easy to operate with a 4.3-inch LCD screen as well as English operation interfaces. Integrated transformer test function greatly improve the test efficiency. The instrument is also provided with multiple interfaces which can meet various requirements of the automatic sorting test, data transmission and storage.
-
Product
Illuminator FTIR Module
Illuminator
-
The MIDAC M4500 series is an ideal solution for dedicated instrumentation and custom sampling configurations. Adapting a conventional laboratory FTIR to these tasks can lead to compromises in performance, awkward and unreliable mechanical fixes, and costly instrument features you simply don't use. The M4500 eliminates all these problems. It's a compact, high performance FTIR module that easily and efficiently integrates with sample interfaces in virtually any configuration.
-
Product
Pressure Instruments Department
-
Aero Instruments & Avionics, Inc.
The Pressure Instruments Department tests, repairs, and overhauls a wide variety of Instrumentation for all narrow and wide body aircraft. Three Martron ATE's are utilized for testing & troubleshooting of Air Data Computers.
-
Product
Amplifier Systems
-
Sutter Instrument provides a complete line of electrophysiology recording hardware and software, ideal for applications ranging from tissue slice patch clamp over dissociated cell recordings to cell line studies.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-03
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
File Import Tool For Importing And Converting STIL, WGL, VCD/EVCD Vectors
DIOEasy-FIT
-
Marvin Test Solutions' DIOEasy-FIT option offers test engineers a software tool set for importing and converting STIL, WGL, VDC/EVCD files to a Marvin Test Solutions' digital instrument file format. DIOEasy-FIT works in conjunction with Marvin Test Solutions' DIOEasy waveform display and editor software which provides an efficient tool set for developing, debugging, and executing digital test vectors for all MTS dynamic digital instruments.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
SpaceWire-USB Brick Mk3
326
-
The SpaceWire Brick Mk3 is a USB 3.0 (also works with USB 2.0 and USB 1.1) to SpaceWire interface device that is suitable for use in all stages of SpaceWire equipment development: initial SpaceWire evaluation, instrument simulation, control system simulation, unit testing, integration support, and EGSE. The SpaceWire Brick Mk3 provides two SpaceWire interfaces, support for high speed data transfer, the capability to inject various types of errors on demand, the ability to transmit and receive time-codes and act as a time-code master, and comes complete with highly optimised host software for low latency transmission of SpaceWire packets directly to and from the host PC.
-
Product
8-Slot BRIC, 168x6, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-801-168x6
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
Sulfur Analyzers
-
Teledyne Analytical Instruments
Sulfur Analyzers by Teledyne Analytical Instruments
-
Product
Large-Scale Vertical Evaporators
EcoChymm X Series
-
Ecodyst® has created the next generation of benchtop and industrial-scale high-speed evaporators for use in laboratory and commercial settings. Using a disruptive refrigerated cooling technology, our evaporators provide eco-friendly and efficient self-cooling metal or Teflon-coated condensers that set new standards for rotary evaporation, distillation, purification, and winterization.All models use a revolutionary tankless cooling technology that is continuously available, provides sustainable temperature control, increases productivity, allows for instrumentation with a reduced footprint, and has low associated operating costs.
-
Product
Synthesizers
-
A low phase noise frequency synthesizer module designed and manufactured for standard test instrumentation, communication, and Radar systems as a local oscillator.
-
Product
DIGITAL MULTIMETER, RUGGED
IBL-19
-
International Biological Laboratories
This rugged instrument, famous for its accuracy and reliability has found a lot of potential for engineers and professionals who look for accuracy. It comes with a holster that provides safety against accidental drops.
-
Product
Large Surface Defect Gauge
4D InSpec® XL Surface Defect Gauge
-
The 4D InSpec XL Surface Defect Gauge expands 4D Technology’s 4D InSpec product line—they’re the first handheld, precision instruments for 3D non-contact surface defect measurement.
-
Product
Industrial Pressure Calibrator
2271A
-
The Fluke Calibration 2271A Industrial Pressure Calibrator provides a complete, automated solution for calibrating a wide variety of pressure gauges and sensors. Thanks to its modular design, it can be configured to meet different needs and budgets, and expanded to cover a broad workload. The 2271A is ideal for calibration laboratories starting out in pressure calibration because it offers wide pressure measurement capabilities in a single instrument. Everything you need for calibrating pressure is included; just connect supply pressure. And your investment will stand the test of time: as your workload grows and changes, the 2271A can grow and change too. Just add measurement modules.
-
Product
Electrochemical Analyzer/Workstation
600E
-
The Model 600D series is designed for general purpose electrochemical measurements. The figure below shows the block diagram of the instrument. The system contains a fast digital function generator, high speed data acquisition circuitry, potentiostat, and a galvanostat (available only in select models).
-
Product
Switches
-
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
Product
Multi-Interface TDM, Optical, And Packet/IP Rackmount & Probe Test Platforms
mTOP™
-
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
Product
PXI 4-Slot BRIC Matrix, 15x32 1-Pole (3 Sub-cards)
40-562B-021-15X32
Matrix Switch Module
The 40-562B-021-15X32 is a high density BRIC4 matrix module with a size of 15x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Tachometers & Accessories
-
An instrument that measures the working speed of an engine, typically in revolutions per minute (RPM).
-
Product
PXI 12-Slot BRIC Matrix, 286x8 1-Pole (13 sub-cards)
40-562B-321-286X8
Matrix Switch Module
The 40-562B-321-286X8 is a high density BRIC12 matrix module with a size of 286x8 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Torque Force Measurement
-
Applying proper torque to screws on an assembly line is critical to the integrity and functionality of manufactured components. Ensuring the application of adequate torque requires a screwdriver, or wrench with the proper range and accuracy of torque measurement. Obtaining the right torque instrument is easy with some understanding of how they work and the various features available.
