PCB
See Also: Printed Circuit Board, PCBA, Crosstalk
-
Product
Automatic Double-Sided Bare PCB Final Inspection AVI System
FI-18 Series
-
InScan Limited (SIP) Co., Ltd.
InScan FI-18 is a compact and high performance fully automatic double sided AVI system for Final Inspection of PCB boards.The setup is based on golden board and CAD data which greatly simplifies the setup process. The FI-18 series inspects and processes a double sided board sized 210X300 mm 5.5 sec. Superior interline high resolution CCD sensor.
-
Product
PCB Adapter, ITA, SIM, VTAC, 32 Pos, 6 Slot, to (1) DisplayPort
510171116
-
PCB Adapter, ITA, SIM, VTAC, 32 Pos, 6 Slot, to (1) DisplayPort.
-
Product
Article Inspection Solution
ExtraEye
-
First article inspection (FAI) in the PCB assembly process is one of the most important steps - left unchecked every mistake from assembly machine setup multiplies into hundreds of incorrectly assembled PCBs. Maximum accuracy in first article inspection is extremely important.
-
Product
Stamped Spring Pin Sockets
-
Ironwood Electronics SBT sockets are small footprint sockets that are compatible with other product lines such as GHz elastomer sockets, Giga-Spring sockets, etc. The socket needs about 2.5mm extra space around the chip than the actual chip size utilizing only very small PCB real estate. A heat sink screw on the top provides the compression force as well as thermal relief and can be customized to dissipate more power. SBT socket uses SBT contact technology for high endurance and wide temperature applications. SBT Contact is a stamped contact with outside spring as well as inside leaf spring that provides a robust solution for Burn-in & Test applications. Solutions are available for 0.3mm to 1.27mm LGA, BGA, QFN, QFP, SOIC and other packages. Contact technology has 3 part system which includes top plunger, bottom plunger and a spring. The Beryllium Copper plungers are stamped and assembled to a stainless steel spring in an automated system to enable fast turnaround time, low cost and zero defects.
-
Product
Signal, Insert, Receiver/ITA, QuadraPaddle ,SIM, Right Angle, 4 Pos, 1 Slot
610138126
-
This insert contains 4 right-angle QuadraPaddle contacts and is designed for soldering directly to a PCB as part of the Infinity Connector system. It is used in the 90 Series SIM Module and occupies 1 of the 34 slots in this module.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
20-Pin Scorpion Female Connector, 30A, Straight PCB Mount
C020AFX-2PS-3A
-
This is a female 20-pin Scorpion Connector, straight, suitable for PCB mounting. The connector is keyed to position 2 and it has a maximum current handling of 30A and is suited for direct connection to Pickering Interfaces products.
-
Product
PCB repair / rework station
XJInvestigator
-
Much more than a production line test tool, XJInvestigator is a repair focused, integrated test and debug environment for fault analysis, helping you efficiently recover your failing boards.
-
Product
Ground Isolated ICP® Pressure Sensors For High Frequency
-
PCB® Series 102B is a ground isolated version of the Series 113B. These sensors have all of the same features and benefits of the 113B Series, plus the added benefit of isolation, which helps prevent ground loop problems. This series can accommodate an optional ablative coating (Prefix: CA) to protect the diaphragm from thermal shock in flash-temperature applications.
-
Product
Oven Performance Checker
OvenRIDER® NL 2+
-
Regardless of the recipe and what your oven's controls indicate, what your PCB actually experiences at board-level as it goes through the oven can be SIGNIFICANTLY different. Achieve convection reflow oven Verification by separating zonal temperatures from convective heat flow efficiency while verifying conveyor speed for a true picture of oven Lead-Free performance consistency.
-
Product
Linear Testfixture (Cassette Not Included), UTT 586 x 248 mm
MG-03
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for changeable cassette
-
Product
BGA Rework Station
PDR IR-E6 Evolution
-
The PDR IR-E6 SMT/BGA rework system, using PDR’s patented Focused IR technology, has been specifically designed to cope with the challenges of repairing today’s Large PCB assemblies.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 230gf
K100-H080230-SKAU
-
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
PCB Data Logger
DL-3
-
The PCB Data logger is a proprietary data logger designed by DLM for use in the offshore industry. Comprising of multiple on-board sensors and with extra capacity for external mV or mA inputs, the DL-3.0 can sample on-board and external sensors at customisable sample rates of up to 800Hz.
-
Product
X-Ray Inspection System
MXI Ruby XL
-
Designed for the largest PCBs, Ruby XL allows 96 x 67 cm (37.9” x 26.4”) areas to be inspected non-destructively, with feature resolution up to 0.5 µm.
-
Product
Small outline PCB with 72 Pin Socket
1091-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
ABex Terminal Module for Göpel 1149Cx-FXT BSCAN Cards
ABex TM-1149Cx-FXT
-
The ABex TM-1149Cx-FXT is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C4-FXT-X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan card it’s possible to connect up to four JTAG/Boundary Scan TAPs. All differential signal wires on the PCB are impedance controlled. In addition, all other digital signals (PIP, TRG, Aux, I/O) and Ground can be switched off via relays.
-
Product
PCB S.I/P.I (Signal Integrity/ Power Integrity)
-
Why need for PCB Simulators?Higher data speed (>GHz) Higher density Larger system size EMI concern Cost cut down Reduce of project term
-
Product
4G SO-DDR3-1600 512X8 1.35V SAM -20~85℃
AQD-SD3L4GN16-SGH
-
SAM Original Chip, Industrial Design for Improved Reliability, PCB: 30μ gold finger, Anti-sulfuration, Semi Wide-temp Support -20~85℃.
-
Product
High-speed 3D Solder Inspection Machine
YSi-SP
-
a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.
-
Product
Automated Multi-Functional Tester
QTouch 1408 C
-
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type E, Ø1.50mm, 155gf
K100-E150155-SKAU
-
K100 Series, Pitch 100mil, Tip Style E, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Original VXI Module Shield Kits
11399x Series
-
* Clamshell design fits C-size modules with 96-pin connectors.* Single-slot kit fits all VXI-1 Revision 1.0 to Revision 3.0 chassis.* Side shields include connector shrouds for maximum shielding.* RFI limiting, air vent slots along top and bottom edges for good air circulation thru the module.* Extruded front panel is bend resistant.* Component side shield has an address switch opening and non-rectangular mounting hole pattern.* Complimentary layout support includes PCB design template and CAD layout files.* RECOMMENDED FOR LEGCY APPLICATIONS ONLY due to its non-rectangular hole pattern.
-
Product
78-Pin D-Type Male Right-Angle PCB
40-963-078-RM
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Press-fit-Tooling
-
The electronics industry is increasingly using Press-fit applications. Through-hole components are increasingly being converted to press-fit solutions. A press is used to push the press-fit connectors into a PCB. This is done in our ESD-safe room. The customised press-fit tooling is used in this process to support the work. The tooling is made of aluminium, brass, stainless steel and ESD-safe composite materials.
-
Product
µHELIX® Test Probes
Series S200, S300, S400, and S500
-
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
Product
Flex, Rigid-Flex, Rigid Printed Circuit Boards
-
PCB boards are a common component of any electronic device. They work as a base for the other components and allow them to interface with one another. A PCB board can be made from several different materials, depending on what you need it for.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 155gf
K100-I126155-SKAU
-
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 155gf, Steel with Gold Plating.
-
Product
TestStation Product Family
-
TestStation In-Circuit Test Systems provide full structural and functional coverage for a wide-range of manufacturing, component, process, and performance for high-performance analog, digital, and mixed-signal devices used on modern PCBs.
-
Product
PCB Track equipotential viewer
EPD100
-
The EPD100 can plot equipotentials on single ended microstrips, and also edge coupled surface microstrips. It allows you to view the equipotential lines around a transmission line.
