-
product
Programmable ECU & CAN Gateway
MICROGen
MICROGen is a control prototyping hardware and software system. It has a range of uses, including as a communications gateway, during testing and for Rapid Control Prototyping.
-
product
BGA Sockets
Ironwood has the most comprehensive collection of BGA (Ball Grid Array) sockets that can be used for prototype application, silicon validation, system development, thermal characterization, burn-in application, functional production test, etc. BGA socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. BGA sockets for prototype applications, silicon validations, system development applications uses low cost elastomer contact technology.
-
product
SSOP-to-DIP Adaptor
Series 651000
SSOP IC to DIP Adapter. Allows the use of .65mm pitch surface mount ICs in thru-hole designs. Ideal for prototyping and testing/evaluating SSOP ICs. Adapter can be cut to smaller sizes by end user. Consult factory for panelized form or for mounting of consigned ICs.
-
product
PXI Prototyping Module, 1-Slot, Dual 20-Pin GMCT
40-225A-811
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Decade Box, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270
Pocket sized resistance decade box ideal for service, prototype and experimental use.*Seven decades of resistance*28 individual slide switches*Terminals with multi way binding posts*Rugged components with ABS plastic housing case*12-month limited warranty *view Terms & Conditions for details
-
product
PCB Test Fixtures
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
product
PXI-8513, 1‑Port, Software-Selectable PXI CAN Interface Module
780688-01
1‑Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
cPCI® Hard Metric Eurocard Plugbord
VECTOR Electronics and Technology, Inc.
Boards for 1mm and 2mm hard metric Eurocard plug-in application with option to mount 2mm hard metric connector on ends. Available with different circuit patterns for prototyping applications.
-
product
PXI Prototyping Module, 2-Slot, 25-Pin D-Type
40-225A-302
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
EIA Based VectorPak
VECTOR Electronics and Technology, Inc.
VectorPak™ subracks offer versatility within a 19” rackmount format. All racks are adjustable in both height and depth, offering standard product solutions for standard and custom requirements. All Subrack sizes are compatible with Vector prototyping boards (see Vectorbord® Plugbord™ section), and can accommodate other sizes as well.
-
product
USRP Software Defined Radio Reconfigurable Device
The USRP Software Defined Radio Reconfigurable Device is built on the LabVIEW reconfigurable I/O (RIO) and universal software radio peripheral (USRP) architectures. It includes a powerful FPGA for advanced DSP that you can program with the LabVIEW FPGA Module. The device includes 2x2 MIMO transceivers or four-channel superheterodyne receivers, supporting center frequencies from 10 MHz to 6 GHz, with up to 160 MHz of instantaneous bandwidth. The USRP Software Defined Radio Reconfigurable Device also optionally includes a GPS‐disciplined oven-controlled crystal oscillator (GPSDO), which provides greater frequency accuracy than temperature- compensated crystal oscillators. Prototyping applications include LTE and 802.11 prototyping, spectrum monitoring, signals intelligence, military communications, radar, direction finding, and wireless research.
-
product
LSS
Power Interface, Prototype Cards and Programmable Resistor Cards for the PXI and GTXI platforms.
-
product
PXI Prototyping Module, 2-Slot, 96-Pin Micro-D
40-225A-102
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
2-Slot 64-bit 6U CompactPCI Backplane
cBP-6402
ADLINK offers a wide selection of standard backplanes from single up to 20 slots. Furthermore, a professional OEM team is capable of custom backplanes with a quick turnaround tailored to your specifications. We make designing, developing, prototyping, and maintaining your projects simple & efficient. For all your backplane needs, give us a call, we have a solution for you.
-
product
Lifecycle Support for Custom Product Development
The parts and components that are rooted in idea generation and product development are the ones that are most likely to succeed. Electri-Cord’s lifecycle support for the production and manufacturing of custom wiring harnesses, cable assemblies, power cords, and high-level assemblies incorporates a four-stage approach that covers the lifespan of the product. This custom product development process includes everything from design prototyping to end-of-life processes.
-
product
Electronics Manufacturing Services
EMS
A production consignment service that develops based on know-how and technological capabilities of "MONOZUKURI " that we have cultivated over many years. Full support from design to board mounting, prototyping, manufacturing, maintenance. We respond to various outsourcing needs such as customer's design consignment and production consignment.
-
product
PXI-8513 , 2-Port, Software-Selectable PXI CAN Interface Module
780688-02
2-Port, Software-Selectable PXI CAN Interface Module—The PXI‑8513 is a software-selectable Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. NI‑XNET Software‑Selectable CAN Interfaces offer the best flexibility for CAN development with onboard transceivers for High-Speed/Flexible Data‑rate, Low-Speed/Fault Tolerant Single Wire CAN as well as any external transceiver. The PXI‑8513 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
Complete and Flexible SMT Solutions
Fritsch offers high quality, small format desktop pick-and-place solutions for prototyping and small batches/short production runs.
-
product
Breadboard to DAQ Converters
0001026-1 / -2
VI Control Systems has designed two converter boards that make it easy to connect data acquisition boards to breadboards and allow easy computer control and monitoring of prototyped electronic circuits. The converter boards are 0.8 x 3.5 inches and have silk-screened pin numbers for every pin on the board. The 68-pin SCSI converter can also be used to connect 68-pin SCSI cables to prototype solder boards that have 0.1 inch centers.
-
product
NI-9862, CAN Interface Module
781639-01
1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The NI‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The NI‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
product
Adapters
- Pluggable BGA adapter system (Giga-snaP™) – Surface mount package emulators – Package convertors & Fix adapters – Prototype, probe & analysis adapters – Receptacles, extenders, rotators and socket plugs– Electronic modules
-
product
Prototype /Short Run Production
We make high precision Prototype /Short Run Metal Stampings & Machined Components.We have been successfully serving industrial clients, mostly OEM Automotive Suppliers, since 2005. We have the ability to take your CAD model and turn it into Production Representative Parts within days.
-
product
Product Safety Testing
NCEE Labs is an A2LA Accredited product safety compliance testing lab. We specialize in compliance testing to US and harmonized international standards. NCEE Labs also offers NRTL testing services. With experienced product safety engineers, we provide expert assistance, whether evaluating early prototypes or assisting with aftermarket design changes.
-
product
Power Interface and Prototype PXI Card
GX7404
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
product
Real-Time Target Machines
Speedgoat offers a range of high performance multi-core, multi CPU target computers (target machines) with i3 and i7 CPUs up to 4.2 GHz, and up to 20 cores. Each is optimized for a different application area, from mobile controller prototyping (RCP) to multi-target rack systems for Hardware-in-the-Loop (HIL).
-
product
HF Amplifier
Prometheus
The design of the Prometheus is the result of over 10,000 hours of research and development, encompassing hundreds of hours of mathematical analysis, computer simulation and modeling, and numerous prototypes and experiments spanning over a five year period. The result is a rugged, commercial quality amplifier designed to run cool under 1500W continuous SSB, CW or RTTY, with special ferrite transformers and combiners designed for full power operation even on 160 meters. Although our custom transformers are more expensive and difficult to manufacture than competing designs, they do not saturate or heat up beyond the Curie point, thereby becoming irreversibly damaged and destroying the RF transistors in the process.
-
product
Electrical Development & Redesign
Your product description goes hereARC’s electrical engineering team has the leg up when it comes to developing or redesigning to your specific requirements.All the way from prototyping to cable design to integration, our talented team of clever engineers can deveop a prototype quickly and get your project off on the right foot. Whether it is a new solution or if you are redesigning an obsolescent FPGA system, our team can provide quickly and effectively while still keeping your budget in mind.
-
product
SparkFun SAMD21 Development Board
Qwiic Micro
Looking for a super small microcontroller to use with the Qwiic eco-system? The SparkFun Qwiic Micro is molded to fit our standard 1"x1" Qwiic standard size which makes it one of our smallest micro-controller offerings to date. At it's core is the powerful and versatile ATSAMD21E18, which is an ARM Cortex M0+, 32-bit microcontroller, with 256KB of flash memory that can run at up to 48MHz! It has 12 digital pins which include 5 analog pins, SPI, I²C, and an additional UART data bus as well as a Qwiic connector for easy integration into the Qwiic ecosystem and I²C prototyping.
-
product
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783927-01
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device - The USRP-2952 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and shorten time to results. You can prototype a range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2952 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
