Wire
See Also: Contacts, Harness, Connectors
-
product
Back and Forth Scratching Tester
WGQ-60
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
product
SparkFun RJ11 Breakout
This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our RJ11 6-Pin Connectors to work with common telephone cables. Each board features standard B/R/Y/G (Black/Red/Yellow/Green) labels on the top of the board to match a standard telephone wire. Additionally, each board has pin numbers on the back side that match with the pins on the connector.
-
product
Liquid Thermal Conductivity Instruments
THW-L1
The Transient Hot Wire (THW-L1) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity, thermal diffusivity, and specific heat instrument for measurement of liquids and pastes in accordance with ASTM D7896-19. The THW-L1 was designed with speed and operational simplicity in mind. With a single measurement of 1 second in duration, small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity, thermal diffusivity, and specific heat. The THW-L1 utilizes a non-stationary measurement approach and rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a thin heating wire 40 mm in length and is completely inserted into the sample to be tested.
-
product
Wire and cable slicer
CX-18
Shenzhen Chuangxin Instruments Co., Ltd.
Wire and cable slicing machine is a kind of used products factory la bequipment. Using mechanical transmission feed, blade cutting structure, it can be cut1 to 12 mm range plastic various thickness, sheet material, etc., they are availablRubber, leather material and hardness of the material must be sliced, the machine is widelyUsed in rubber, plastic, leather, electric wire, cable, scientific research units, etc.
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 2m, Screwlocks
A068SMR-C-6B200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Plug & Play JTAG/SWD Microcontroller Debugger with Built In GDB Server & UART
Black Magic Probe V2.3
In most cases Black Magic Debug takes the form of a firmware for the Black Magic Probe hardware, and implements a GNU DeBugger (GDB) server.The Black Magic GDB server features: - Automatic target detection- No need for target specific configuration scripts- All protocol and target specific control is done through GDB monitor commands- No “software in the middle” like OpenOCD required- Easily scriptable thanks to the GDB scripting capabilities- Interface to the host computer is a standard USB CDC ACM device (virtual serial port), which does not require special drivers on Linux or OS X.- Targets ARM Cortex-M and Cortex-A based microcontrollers- Provides full debugging functionality, including: watchpoints, flash memory breakpoints, memory and register examination, flash memory programming, etc.- [Semihosting / Host IO support] as well as [Serial Wire Debug TRACESWO support].- Implements USB DFU class for easy firmware upgrade as updates become available.- Works with Windows, Linux and Mac environments.
-
product
Eurocard Plugbord
E160-3U-2
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
product
Concrete Imaging with Ground Penetrating Radar GPR
Conquest 100
Conquest GPR: Get rapid, reliable results and reduce the need for destructive testing. Conquest GPR is a light, portable device that provides a fast, non-invasive method to gain accurate insights of objects below the concretesurface, even on a curved surface or column. Conquest GPR reduces risk by detecting rebar, post-tension cables, metallic and non-metallic conduits as well as current-carrying wires embedded in concrete. Once your concrete scan is complete, Conquest GPR connects to your mobile device, allowing you to email information directly from the field. Back in the office view your data and make client-ready reports in minutes.
-
product
ITA, I2 Micro ICon, 168 Position, With Oversized Backshell
410130106
The i2 Micro iCon ITA with oversized cable clamp is capable of holding up to 168 QuadraPaddle contacts. With a wider 1.97” footprint, it is ideal for applications requiring shielded twisted pair wiring or other wire types with oversized jackets. The 30-degree u-shaped cable clamp allows ITA modules to be pre-wired before assembly and can hold cable bundles with an oblong bushing effective diameter of 1.80". The removable cover allows easy access to wiring for maintenance and probing. Integrated spring locking tabs ensure even and secure engagement.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 1m
A037DM5-C-0A100
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation . Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
LAN Check With Tone Generator
PH-01
The LANCHECK consists of two modular units, a tester and a remote terminator. The modular design enables the tester to be used for local loop-back testing of patch cable or remote testing of pre-installed premise wiring. The LANCHECK makes it easy to recognize opens and shorts within a cable as well as identify reversed and miswired cables. It can verify a cable up to 2,000 feet in length. Furthermore, it comes with shielded connectors, which enables the testing of shielded twisted pair (STP) cables. It also features convenient Auto Scanning and precision Manual Scanning modes.
-
product
Cable Testers
DMX ADAPTER
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
product
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509
510140113
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509.
-
product
Cable Assy 25-Pin D-Type F/F 0.5m
40-970-025-0.5m-FF
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
3U cPCI Serial 5-Port Gigabit Ethernet NIC
SN1-REVERB
The SN1-REVERB is a peripheral slot card for CompactPCI® Serial systems. The board is equipped with five independent PCI Express® based Gigabit Ethernet controllers, wired to associated RJ45 front panel jacks.
-
product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 0.5m
A020GFR-C-0C050
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
Spring Contact Probes
FEINMETALL offers a wide range of contact probe:ICT / FCT probes, short travel probes, double plunger probes, fine pitch probes, interface probes, wire harness probes, threaded probes, high current probes, switch probes, twist proof probes, push back probes, koaxial probes, radio frequency probes.
-
product
HIL Breakout Board
Onboard 192 pin snap-in terminal dramatically simplifies the wiring between your control hardware and your HIL system. As soon as the system is up and running there are 192 test terminals for easy access to all the interface signals: firing pulses, control feedback signals and other analog/digital I/O signals.
-
product
Ultrasonic Level Transmitter
USonic
The Drexelbrook family of Ultrasonic technology level products offers an affordable two wire and line powered version for non-contact level measurement of liquids and slurries for level, distance, volume and open channel flow.Measurements of level, distance, volume and open channel flow is easily configured through the menu driven display. The Usonic level transmitter is offered with a two wire 4-20 mA, Hart output signal and is suitable for all Class I Div. 1, Zone 0, I.S. or XP locations. The bench configuration eliminates the need to move process material levels for calibration.
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends
A068SFR-T-5A200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
Network Test LanCaster Pro ST
The NEW Lancaster Pro-ST is a low-cost wire map tester which tests and certifies structured cabling continuity to a TIA568A/B, USOC and ISDN standards. The new Lancaster Pro-ST displays on screen wiring configurations showing the length of all 4 pairs and length of pair to fault up to 150m (500ft).
-
product
MP CI set
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)
-
product
4-Wire Universal Cable Tester
LX-860
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface·Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V
-
product
Connector, Cable Mount, 25 Pin 1.27mm Pitch Micro-D, Female, Crimp Pin
C025CFR-1CP-0A
This 25 pin micro-D connector is designed to allow users to directly terminate with crimped connections and is suitable for 26 AWG copper wire. Screwlocks are provided to secure the connector to its associated product. This connector is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
DIN Backplane
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
product
Solid State Active Synchro Control transformer and Solid State Resolver Control Transformer
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).
-
product
RTD Simulator PCI Card 6-Channel PT1000
50-262-102
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card can provides a setting resolution of <90mΩ (also available in <8mΩ - PT100) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
product
Low Circuit Tester
26250
Helps locate shorts or breaks in wiring. Complete with insulated grounding clip.
-
product
Rotatable Directional HF Antennas
Kratos Defense & Security Solutions, Inc.
Kratos’ horizontally polarized rotatable log-periodic antennas are constructed with wire radiators supported by a strong and unusually lightweight support structure.
-
product
Wiring Boxes
Radio receiver for heating / cooling systems equipped with an integrated antenna, an output with SPDT relay and an RS485 Modbus® RTU slave communication port.
