Wire
See Also: Contacts, Harness, Connectors
-
Product
Cable Assy 37-Pin D-Type M/M 1m
40-970-037-1m-MM
-
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 37-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
3-28V Cordless Circuit Tester
1948
-
Peaceful Thriving Enterprise Co Ltd
With CE & UKCA Approvals. Detect voltage from 3V to 28V. No ground wire or clip required. Replaceable long-life alkaline batteries included.(Power supply: SUM5 1.5V X 2 pc). Safe with ECMs, sensors, transducers and air bags.
-
Product
Protective Cover, 9050, VXI and Discrete Wiring, ITA
410114298
-
Protective Cover, 9050, VXI and Discrete Wiring, ITA.
-
Product
Circuit Breaker Finder Accessory Kit
69411
-
For use with ET300 Digital Circuit Breaker Finder.Light socket adapter for finding the correct circuit of a lighting fixture.Alligator clip adapter enables use of on bare wires.
-
Product
LAN Check With Tone Generator
PH-01
-
The LANCHECK consists of two modular units, a tester and a remote terminator. The modular design enables the tester to be used for local loop-back testing of patch cable or remote testing of pre-installed premise wiring. The LANCHECK makes it easy to recognize opens and shorts within a cable as well as identify reversed and miswired cables. It can verify a cable up to 2,000 feet in length. Furthermore, it comes with shielded connectors, which enables the testing of shielded twisted pair (STP) cables. It also features convenient Auto Scanning and precision Manual Scanning modes.
-
Product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
Product
LAN Testers
-
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
Product
High-Speed DB37 Cable
PCL-10137H
-
Double-shielded cable with high Speed 37-pin D-sub connectorsD-Sub 37 pin male x 2Tinned and strand copper wire with drain wire x 1Aluminum/Mylar foil and braided copper double-shielded cableIsolated P.V.C. jacketUL20397 approvedColor : GrayWeight 375g
-
Product
SPARK LXi2 Bluetooth Handheld Datalogger
PS-3600B
-
This is a Bluetooth, handheld science datalogger that lets students connect multiple wired and wireless sensors, collect data, generate live graphs, and perform data analysis.
-
Product
Cable Assy 37-Pin D-Type M/F 2m
40-970-037-2m-MF
-
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products.
-
Product
Pneumatic Flat Grips
-
For tensile testing rubbers, plastics, elastomers, textiles, cloth, and paper, in specimen geometries such as plates, films, and wires, a good option is pneumatic flat grips. Quick clamping and a repeatable clamping force are advantages of pneumatic flat grips.
-
Product
USB Extenders / Repeaters / Hubs
-
CommFront has all the solutions that you need to make your data travel seamlessly without limits. We offer a range of rugged, industrial-grade USB extenders (repeaters) and hubs to meet your data communications' distance needs by converting unbalanced signals to balanced ones, deploying repeaters to boost signal strength, and implementing hubs for star-configured connections, while still taking full advantage of cost-effective and readily-available copper wire.
-
Product
10 Micron Wire Grid Polarizer
-
Fabricated from 10 micron diameter tungsten wire, and with a choice of wire spacing starting from 25 microns, these wire grid polarizers are suitable for use from approximately 100 microns (or 3 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 1m, Spring Latch
40-972A-068-1m-FU
-
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Split type AC Current Transformer
CTF-100T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Wire stopper is equipped for the slipping protection.*The special connector is not necessary as the output terminals are provided.*Open circuit protection and nonflammable plastic material.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
-
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
50/75 Ohm Micro Coax Contacts
-
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
Product
Connector, 50-Pin SGMC, Female, 5A, Crimp Pin, With Backshell
C050FFR-1CP-0A
-
This 50-pin SGMC connector is designed to allow users to directly terminate with crimp connections and is suitable for 22 AWG copper wire. Supplied with a backshell that has an integral cable clamp. Screwlocks are provided to secure the connector to its associated product.
-
Product
Cable, 96-Pin 1.27mm Pitch Female To Unterminated, Ferrules, Screwlocks, 0.5m
A096SFR-F-6A050
-
The 96-Pin 1.27mm Pitch to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
Product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
-
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Product
20-Pin Scorpion Cable, Female to Unterminated, Tinned Ends, 30A, 2m
A020AFR-T-3A200
-
This is a 2m long female to unterminated 20-Pin Scorpion cable assembly with tinned ends constructed from 37/0.4 (10AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
32-CH Discrete Output Modules with U Profile
HSL-DO32-UD
-
*UD type is suitable for screw type wiring. Each wire to sensors or actuators can be fixed by the screw terminal*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitation and cost-effective requirement*Support 32 DO channels*Transmission speed: 3/6/12 Mbps
-
Product
20-Pin GMCT Cable, Female to Female, 10A, 1m
A020GFR-020GFR-0B100
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Scanners
-
Measurements International Ltd.
Sealed Relays with 4 A Carrying Capacity, 4-Conductor Wire or Binding Post Inputs, Low-thermal Matrix Design.
-
Product
Polarity Indicator Circuit Tester
CT8007
-
No ground wire means no wire tangles nor time lost searching for grounding points. High Impedance electronic circuitry. Negligible current draw ( 1 microampere) is 30,000 times less than regular lamp type testers. This gives complete safety when working around sensitive electronic control modules and sensors. Operating range between 6 and 28 Volt DC in battery powered systems
-
Product
Time Domain Reflectometer
TDR-420
-
TDR-420 is a hand held Time Domain Reflectometer designed to identify and locate faults in power, telecommunications and teletechnical cables. TDR-420 reflectometer allows to measure the length of the cable and determine the distance to damage or impedance variation in the range of 4 m to 6000 m in conductors with metal wires. The shortest measuring range of 7 meters and a dead zone of 0.6 meters allows to locate damages at a very close distance from the place where the device is connected.
-
Product
Serial RS-232 Expansion Connector Accessory for USBHub3c
-
Used for connecting a serial RS-232 interface to the control the USBHub3c through the expansion interface connector. Screw terminals are provided for the RS-232 interface. While this board provides for wiring connections, a host machine external to the USBHub3c is required for this control interface.
-
Product
4-Pin Power D-Type Cable, Male to Female, 2m
40-970-404-2m-MF
-
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Receptacle Tester w/GFCI
61-501
-
*Warns against faulty wiring in 3-wire receptacles*For use on 120VAC circuits*1-year warranty
-
Product
Saluki S2107 Series Optical Cable Identifier (up to 36dB)
-
S2107 Series Optical Cable Identifier is an intelligent instrument designed for the construction and maintenance of optical cable lines in optical communication system. In view of the complex wiring environment and the difficulty of locating faults during the construction and long-term use of optical cables, S2107 series can provide fast, effective and accurate fault solutions. When the target optical cable is bent or shaken, the optical cable census instrument can quickly capture the vibration signal and display it through waveform and sound, so as to locate the target optical cable quickly.
