Strain Gauge Amplifiers
-
Product
Strain Gauge and RTD via Ethernet
2612
-
Simultaneous measurement of four strain gauges or RTDs6 or 4-wire measurement with 200 nV resolution at a 6 Hz rateAuto-calibration cycle measures excitation at remote strain gaugeCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
Product
Programmable Oscillator Amplifier
Amplifier
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
Product
USB Preamplifier, 10 MHz to 4 GHz
U7227A
Amplifier
The U7227A, 10 MHz to 4 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurements.
-
Product
Rosette Strain Gauges
-
Rosette Strain Gages have three measuring grids arranged at an angle of 0°/45°/90° or 0°/60°/120°
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
Product
Reusable ICP® Strain Gauge
-
This high-resolution dynamic alternative to bond foil strain gauges uses a quartz sensing element in a durable, titanium housing. It has 0.0006 microstrain resolution, 5 volt output, 100k Hz frequency response and 0.5 gram mass for lightweight test articles. The reusable sensor comes with a calibration certificate, attaches to the test specimen in 60 seconds and is removed in 10 seconds.
-
Product
4 Channels, Strain Gauge Measurement
SG1
-
Module SG1 is NAI’s latest generation Strain Gage Measurement Module. This intelligent, four-channel module is used on our Multifunction Embedded I/O Boards and Single Board Computers (SBCs).
-
-
Product
Dual Parallel Strain Gauges
-
Dual Parallel Strain Gauges strain gauges have two measuring grids arranged parallel to each other. Typical applications include measurements on bending beams
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 3k
50-265-102
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Digital Indicator for Strain Gauge Sensors
AD-4530
-
Low cost digital indicator for various applications. Suitable for measurement of load, pressure, torque, tension and more at an affordable price.Digital Zero (DZ) stores zero data at any measurement point. This function can also be used to tare weight. Measurement can simply be restarted when it was interrupted by a loss of power.Power on zero function adjusts to zero when the power is turned on.Digital filter provides stable measurement results.Digital span calibration. Easy calibration just by inputting the rated output of a sensor. No need to use a mass.
-
Product
Signal Amplifier
9100A
Amplifier
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
Signal Amplifier
9100
Amplifier
Model 9100 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9100 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
Product
Synchro Power Amplifiers
SSP
Amplifier
Computer Conversions Corporation
The SSP Series are Compact, Reference Powered and Isolated Synchro Power Amplifiers, and AC Sine/Cosine ( Resolver ) to synchro converters; designed for moderate wattage, and re-transmission requirements; providing ultra high efficiency, and ultra high reliability in service, and ease of use. They are ideally suited for demanding Naval/Maritime, Aircraft, and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and active control systems. They are suitable to drive both CT and CDX type passive loads, and virtually any synchro input instrumentation, or control.
-
Product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
-
Product
Strain Gauge Module
МТМ8
-
Mezzanine module (mezzanine) МТМ8 is designed to measure the output signal of strain gauges. The mezzanine can be used with any bridge sensors (pressure, force, etc.).
-
Product
PXIe Single Channel 20GHz 30dBm RF Amplifier
3201
Amplifier
Model TE3201 is a single channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
Product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-4
-
4 channels for the acquisition of strain gauges. 4 onboard voltage sources. 18-bit resolution. Optical isolation 1000 V. Software linearisation. Direct connection of the pressure sensors with terminal board PX3200
-
Product
Isolated Strain Gauge Input Module
ADAM-3016
-
1000 VDC 3-way optical isolationSwitch configurable mV or V input of full bridgeSwitch configurable voltage and current outputs
-
Product
Strain Gauges
TSM
-
We have been designing and manufacturing strain gauges for over 50 years and one of the earliest members of the British Society for Strain Measurement: Linear Strain, Dual Strain, Full & Half Bridge, Rosette & Circular, Bonding Services, Torque & Shear Strain Gauges and Bi-Axial/Tri-Axial Strain Gauges.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 1K
40-265-202
Strain Gauge Simulator
The 40-265 is a strain gauge simulator that simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Strain sensors
SG-01
-
The Strain Gage SG-01 is the fibre optic equivalent of an electrical strain gage. The Strain Gage SG-01 can be mounted directly on the surface of a structure by means of an adhesive. In this way, the fibre sensor makes direct contact with the surface and therefore measures directly the strain at the surface.
-
Product
High-Temperature Strain Gages
ZWH-, ZWN-, & ZWP-Series
-
ZWH-, ZWN-, and ZWP-Series strain gages are designed for dynamic and limited static strain measurement at hightemperature.These strain gages are manufactured using a round wire for superior bonding ability and performance. A high-fatigue wire (Option Z) is also available on each of the gages. These gages are supplied with a fiberglassreinforced tape carrier which holds the grid and leads in place during installation and are bonded using ceramic cements or Rokide® flame spray. The shelf-life of thesegages is 9 months.
-
Product
Amplifiers
-
Amplifiers from Analog Devices deliver both high performance and high value. These amplifier ICs combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
Product
Signal Amplifier
A10160
Amplifier
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
Product
PRECISION GAUGE
PX-7 DL
-
The PX-7DL has all the features of the PX-7 plus a data logger that stores a total of 1000 readings in 10 files of 100 readings each file. Complete with file transfer software.
-
Product
Force Gauge
-
The Centor range of digital force gauges offers force measurement solutions for every situation. From the simple Centor First II force gauge to the colorful Centor Easy II, we have a wide range of instruments designed for industrial and laboratory use.
-
Product
Amplifiers
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a large portfolio of high performance broadband RF amplifiers. Optimized for linearity, high dynamic range and low noise, they cover all widely used radio standards like cellular, satellite radio, TETRA/BOS, GNSS, GPS, 802.11, including the new bands for LTE-U. They amplify wideband radio signals from shortwave over UHF, VHF up to 18 GHz in 50 Ohm technology (I-band, G-band, P-band, L-band, S-band, C-band and X-band). They are used as compact RF drivers, antenna pre-amplifiers or RF boosters in a variety of applications ranging from tunnel radio coverage extension, over airspace radio monitoring to in-ear monitoring and can also be offered as 1U 19” rack variants. Due to their advanced design, the power consumption is significant lower than typical industry alternatives, saving cost at customers with respect to cooling.
-
Product
Depth Gauge
-
• Integrated Bluetooth® Smart data transmission• Special depth gauge double with adjustable anvil and clamping screw• Programmable button according to your needs• Water protected for heavy-duty work with coolants and lubricants, protection rating IP67 according to IEC 60529,• Automatic wake-up by moving the electronic on his frame. (Absolute System S.I.S)• Sleeping mode after 20 min. of no use. (Absolute System S.I.S)• Position memorized in sleeping mode, Absolute System S.I.S*• Maximum speed of displacement : 2.5 m/sec• Mechanical frame in stainless steel, hardened and grinded
