Carriers
Carrier devices are practical for adapting your product to a standard interface for testing on the bench or in the chamber.
-
product
25-Pin D-Type Male Connector Block
40-965-025-M
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
product
CATV Multi-Carrier Generator
1685
The Model 1685 is a headend / hubsite RF eight carrier generator. Each CW carrier can be activated individually or simultaneously. The RF carriers generated are extremely clean and stable, thus making the 1685 an ideal instrument for testing/aligning the CATV forward band.
-
product
Dual PMC Carrier for 6U CompactPCI
TCP262
The TCP262 supports standard PMC front I/O and CompactPCI rear I/O fully compatible to the TCP260. The PMC slot 2 (upper PMC) I/O lines are connected directly to the CompactPCI connector J5. The PMC slot 1 (lower PMC) I/O lines are connected directly to the CompactPCI connector J3.
-
product
FMC Expansion I/O Module.
SI-MOD32xx
The SI-MOD32xx is a family of high resolution, FMC form factor, high channel count multi function data acquisition and control modules that plug into any SI-DSP or FPGA carrier card.
-
product
Analog Output Industry Pack Module, 12-bit D/A
IP220A
The IP220A outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
-
product
Universal Military Craft Systems Controller
3U VPX
The system is 3U VPX based. It consists of two CPU modules, a power supply module [SMART.PSU] Technology explained <- Click here, two PMC/XMC carrier modules and two MILBUS modules. Optional: WLAN module for controlling the system externally without hanger access (Aircraft on runway - pre-takeoff)
-
product
Microwave SPDT Plug-In Switch Card
1260-160B/E
The Astronics 1260-160B/E is a 1 or 2-slot microwave switch plug-in for use in either the Astronics 1260-100 Adapt-a-Switch™ VXI carrier or the 1256, GPIB/RS-232 Switching Mainframe.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 4 M.2 PCIe SSD Modules
SKU-086-34
PCIe Carrier board was designed to expand modern motherboards that have PCIe interface. It allows connection of up to 4 M.2 PCI Express SSD modules.PCIe Carrier board is one-slot-wide, half-height and it compliant with PCIe Specification 3.0 and M.2 Specification 1.1.
-
product
Standard Type Externally Modulated Optical Transmitter
HT8500H
Hangzhou Huatai Optic Tech. Co., Ltd.
1550nm externally modulated optical transmitter is the core equipment in the RFTV network system.RFTV is a unidirectional analogue and digital video broadcast. It adopts high efficiency modulation mode for RF carrier wave and its economy , flexibility and bandwidth validity is beyond comparison of IPTV. By adopting EPON, GEPON or P2P access mode to realize triple-play and FTTx, RFTV broadcasting network in 1550nm optical wavelength still plays an important role.
-
product
Distributed Antenna Systems (DAS)
Morcom's DAS as a Service (DAaS) is a new offering in the Connectivity as a Service (CaaS) portfolio. Distributed Antenna Systems (DAS) are an appealing option for building owners and real estate venue operators. Why incur in the capital expense of purchasing a DAS when you can have the same cellular coverage in your venue and pay for it as a monthly expense (where it will be offset by the money you're saving through IoT innovation and productivity). Morcom’s CBRS Private LTE band and Neutral Host DAS solutions are available to all carriers.
-
product
System on Module Microsemi PolarFire
SoM3-MPF300T
Sundance Multiprocessor Technology Ltd.
The SoM3-MPF300T is a small footprint System On Module (SoM) with 40x50mm dimensions. It has a low power, highly secure FPGA from the PolarFire family from Microsemi. It comes with 4GB of DDR4 memory, Ethernet PHY, and FLASH. This SoM is ideal for being used in complex hardware designs, and is compatible with Sundance SoM carriers SE215 and EMC2-DP-V2.
-
product
Carrier Board for Hilscher Fieldbus
SF1-STUDIO
SF1-STUDIO is optimized for Hilscher real-time Ethernet & fieldbus modules. Many popular protocols are supported. Ethernet, mezzanine modules are available for EtherCAT, EtherNet/IP, Open-Modbus/TCP, POWERLINK, PROFINET IO, Sercos, and VARAN.
-
product
DCME Analysis System
DCME Analysis System (SCL-DAS) is a software based application, which is designed to classify, process and decompressed the compressed signals transmitted over the satellite links.DCME Analysis System supports most of the commercially available DCMEs including PCM, ADPCM, DX-3000, DX-7000, DTX-600, DTX-360, DTX-240 (D,E,F,T), CELTIC-3G, OKI TC-2000 etc. While processing the compressed/normal E1 carrier, the SCL-DAS provides the processed intelligible output in the form of Voice and Fax along with Originating Point Country, Destination Point Country, Outgoing Number, Incoming Number etc.
-
product
FMC Module
SMT-FMC510L
Sundance Multiprocessor Technology Ltd.
The SMT-FMC510L is an FMC module with a low pin count connector (LPC). It is primarily designed to attach to the EMC2-DP FMC PCIe104 carrier board and provide analogue video and serial interfaces. Connectivity is via BNC connectors on the main FMC PCB, BNC connectors on an adaptor PCB, and two 20-way latching DIL pin headers. The adapter PCB is optional and only required if interfaces other than analog video are needed.
-
product
Carrier Boards
Advantech Development boards provide a schematic software & reference design to reduce efforts needed in development stage. Advantech Development Board can be used to test carrier board problems and support COM series, and Qseven, ETX / XTX form factors.
-
product
MIL-STD-1553 & ARINC PMC Interface Card. Supports cPCI/PXI Backplanes
CPCIC3/6-MA4
Alta Data Technologies’ CPCIC3/6-MA4 (PXI Compatible) interface module is a multi-channel, multi-protocol 1553 and ARINC PMC on 3U (PXI Compatible) or 6U carrier card supported by the latest software technologies. This hardware and software package provides increased system performance and reduces integration time.
-
product
LEC-Starterkit with LEC-BASE 2.0 Carrier, SD Card and ATX Power Supply (without LEC Module and Cooling Solution), Optional LVDS Display
LEC-Starterkit 2.0
The LEC-Starterkit 2.0 consists of a SMARC 2.0 compliant LEC-BASE 2.0 carrier board, data media, an AC/DC adapter, power cords and is suitable for LEC-AL, LEC-BT, LEC-BTS or LEC-BW modules.
-
product
3U CompactPCI Serial 2.5" SATA Storage Carrier
cPCI-A3H10
- 3U 4HP CPCI-S.0 peripheral- One 2.5" SATA 6Gb/s drive slot- Status LEDs on faceplate: drive activity, hot-swap status, user-configurable- Hot swap support- Operating temperature: -40°C to 85°C with qualified com
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - 3U VPX
Model 5953
- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional VITA-66.4 optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA-46, VITA-48, VITA-66.4, VITA-57.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products- Model 4801 Carrier Design Kit for designing custom carrier for the Model 6003 QuartzXM- Model 6003 unique QuartzXM eXpress module enables migration to other form factorsPentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products VideoLive Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boardsPipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoCSynchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPXPlease refer to the product datasheet for Installed FPGA IP Module details
-
product
ID Reader 8
ID Reader 8″ is the best tool to avoid lot errors. Designed for using 200mm – 8″ notch aligner and OCR system, it checks your carrier tag, reads each wafer scribes, then sends the information to your Host with SECSII Gem commands
-
product
8 Channel Relay Board for Signal Isolation
FXA-104 Relay 8CH
The FXA-104 is a relay board to switch signals with 8 SPDT channels. It’s eight channels can be switched individually with a low active input. Each channel is equipped with a status led and capable of switching up to 2A. Due to its wide range input it’s very flexible to use and it is delivered with an installed DIN rail carrier.
-
product
16 Channel 12C Relay Expansion
FXA-105 I2C Relay 16CH
The FXA-105 provides sixteen I2C controlled relays. It is equipped with a wide range 7V to 24V power supply and based on a 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
product
Matrix Switch Cards
1260-145 Series
These quickly and easily plug into the front of Astronics 1260-100 and 1260-101 Adapt-a-Switch™ carriers or Astronics 1256 GPIB/Ethernet and 1256L (LXI Core 2011 Compliant) switching mainframes.
-
product
Interface Card
XMC-1553
The XMC-1553 Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Ideal for SBCs or carriers for VPX, VME and cPCI (Compact PCI/PCIe or PXI) - Commercial or Rugged/Conduction Cooled Systems.
-
product
Quad IP Carrier Module With Front I/O
DP-cPCI-5202
DP-cPCI-5202 IP carrier board provides electrical and mechanical interface for four industry standard IP modules. The board provides full data access to the IP modules I/O, ID and memory spaces. The programmable registers are used for configuring and controlling the operation of IP modules.
-
product
COM Express Type 6 Basic Module With Intel® Xeon® E3/7th Gen Intel® Core™ I7/i5/i3 Processors And Intel® CM238/QM175/HM175
CEM510
The CEM510 is based on the Intel® Xeon® E3 and 7th generation Intel® Core™ i7/i5/i3 processors with Intel® CM238/QM175/HM175 chipset. The 125 x 95 mm system-on-module was designed for graphics-intensive applications over the Industrial IoT, including industrial control, medical imaging, digital signage, and gaming machines. The embedded module is equipped with dual 260-pin DDR4-2133 SO-DIMM slots with up to 32GB system memory. Its wide operating temperature range of -40°C to +85°C strengthens the adaptability of various harsh conditions. For evaluation and development purposes, Axiomtek also has the CEB94011, a carrier board designed to operate with the CEM510 for additional I/O and expansions interfaces. Integrated with Intel® Gen 9 graphics, and with the support of DX12.0, OCL 2.0 and OGL 4.3, the module presents excellent graphics performance with resolution up to 4K (3840 x 2160 @ 30 Hz). Three independent displays are supported through LVDS and three DDI ports supporting HDMI, DisplayPort, and DVI (one DDI supporting optional VGA).
-
product
Dual Vapor Gravimetric Sorption Analyzer
DVS Resolution
DVS Resolution’s key feature is the combined ability to precisely control and measure temperature and relative humidity while recording the highest resolution changes in mass. DVS Resolution uses a dry carrier gas typically nitrogen or compressed air for its operation. Digital mass flow controllers regulate flows of dry and saturated gases. Relative humidity is generated by precisely mixing dry and saturated gas flows in desired flow ratios which produce expected relative humidity. In a typical experiment a known concentration of water vapor is delivered over a sample placed inside the sample pan connected to the Surface Measurement Systems Ultrabalance™ measuring realtime mass changes caused by sorption or desorption of water molecules. Prior to sorption measurements, the sample can be in-situ preheated/dried at temperatures of up to 300oC.
-
product
4-Band SAT-IF Overlay Direct Modulated Optical Transmitter
HDS-55S ( 950~5500MHz )
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDS-55S series 1550nm wide band micro-wave internal modulation optical transmitter， RF working 950~5450MHz.It cam It can transmit multi( stacker) 4 way SAT-IF signal in one fiber to realize two polarized 4 way SAT-IF signal in one satellite。or 4 way SAT-IF signal in different satellites to convert all of them into one fiber.。Through FTTH，users use ordinary satellite receiver and STB to receive satellite video carrier the integrate TV programs. It can supply high quality of satellite TV service up to 3000 SDTV or 600 HDTV channel.
-
product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
product
Expansion I/O Module.
SI-MOD66xx
The SI-MOD66xx is a family of high resolution, multi function data acquisition and control modules that plug into any SI-CxDSP carrier processor card for the PCI bus.
