Polarization
property of transverse waves which specifies the geometrical orientation of the oscillations.
See Also: Resistivity & Induced Polarization, Resistivity, Polarizers
-
Product
Universal Multichannel System up to 500V
-
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 500 V output voltage (0 ÷ 250 V, A1519B and A1619 only)- Maximum Current 0.5, 1, 10 mA or 1 mA/100 μA (dual range boards)- Individual Enable (A151x only)- Either DB37, DB25, Radiall Multipin or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA, 100 pA current set / monitor resolution- Up to 10 mV / 1 mV voltage set / monitor resolution- Very Low ripple, down to < 5 mVpp- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Full Floating (A151x, A1612, A1619)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A151x)
-
Product
SMART MEGOHMMETER
MD-5060x
-
The Megabras MD-5060x is a smart, microprocessor-controlled, 5 kV insulation tester. Besides the conventional measurement of insulation resistances up to 5 TΩ, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.
-
Product
PXI Solid-State Matrix Module, 6x2, 10 A
40-553A-011
Matrix Switch Module
The 40-553A-011 is a high current 6x2 matrix occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each matrix switching path can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Portable Electrical Management Systems
EMS-HW30C
-
Progressive Industries Portable Electrical Management Systems (EMS) provide full RV protection against all adverse power conditions. You will feel secure with multi-mode surge, voltage, polarity and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: Voltage(s), current, frequency, error code, and previous error code (if applicable). Replacement parts are simply plug-and-play, making repairs quick and easy. As with our portable models, the computer is driven by state of the art microprocessors. Should the software ever change, EMS owners can receive a free upgrade at no cost.
-
Product
Dual-ridge Horn Antenna 1 to 18 GHz
EH118
-
EH118, a dual-ridge horn antenna that will operate from 1 to 18 GHz. This antenna has a balanced, smooth antenna factor curve that extends all the way to 18 GHz, a reduction of higher order modes on the aperture, and low return loss (SVSWR). The EH118 is applicable for commercial, military and automotive test standards and will include applicable calibrations. The EMC dual-ridge horn antenna offers these key features: single linear polarization, smooth/balanced gain with frequency, low return loss /VSWR, and ultrawide bandwidth (18:1).
-
Product
Rectangular Horn Antennas
-
SAGE Millimeter wave rectangular gain horns, also called pyramidal gain horns, are offered as both standard and custom models with a rectangular waveguide interface. The pyramidal gain horns only support linear polarization. With a calibrated gain chart, these horns can be used to measure the gain of other antennas by comparing the generated signal levels of both. For this reason, these horns are also referred to as standard gain horns. The listed models offer 23 dB nominal gain, 10/11 degrees typical half power beamwidth and 14 dB/30 dB typical side lobe levels at the center frequency of the band. These horns cover full waveguide bandwidths within the frequency range of 8.2 to 170 GHz. In addition to the models listed below, models with 10, 15, 20 and 25 dB gain and other frequency bands are also available.
-
Product
Planar-Doped Barrier Diode Detector, 10 MHz to 33 GHz
8473D
-
The Keysight 8473D is a high-performance detector using a gallium arsenide, planar-doped barrier detecting element. It features extremely flat frequency response over its entire band of operation and very good frequency response stability versus temperature. The Keysight 8473D is also very rugged with high resistance to ESD damage. An optimum square-law load and positive polarity output are available as special options (consult your local Keysight representative).
-
Product
Optics
-
Rising from our Qioptiq® heritage, Excelitas now offers precision optics in most every form and spanning the entire spectrum. You can choose from more than 4,800 off-the-shelf optical products! Our selection includes plano-convex lenses, biconvex lenses, aspheres and achromats with individual coatings, as well as plano optics, mirrors, polarization optics, electro-optics and optical design software and of course our optical assemblies and systems, such as objective lenses, optronics modules, and complex custom sub-assemblies and turn-key systems.
-
Product
Instrument Transformer Calibrators
CTPT 81
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Tests: Ratio error. Excitation current and curve. Polarity CT / PT TESTER
-
Product
2D Geophysical Inversion Software for Resistivity and Induced Polarization Data
RES2DINV
-
RES2DINV software is designed to interpolate and interpret field data of electrical geophysical prospecting (2D sounding) of electrical resistivity (conductivity) and induced polarization. The inversion of the resistivity and IP data is conducted by least-square method involving finite-element and finite-difference methods. The software can handle data from any electrode array, including Wenner (a, b, g), dipole-dipole, inline pole-dipole, pole-pole, Wenner-Schlumberger, equatorial pole-dipole and non-conventional arrays. Interpolate data from land, under water, and cross-borehole surveys. Easy data conversion from the most popular geophysical instruments including ABEM Lund, Syskal, AGI, PASI, IRIS, SCITREX, etc.
-
Product
Turning Mirror on Universal Mount
10769B
-
The Keysight 10769B Turning Mirror on Universal Mount deflects a laser beam at any angle, in either the vertical or the horizontal polarization plane of the beam. The 10769B contains the same turning mirror as the 10769A, but has a different mounting.
-
Product
Gratings for Astronomy
-
HORIBA Scientific proposes large size Transmission Holographic Fused Silica Etched (FSE) gratings or Ruled blazed reflection gratings for Astronomy.Both technologies offer a very high efficiency, low polarization dependence and low angular sensitivity.
-
Product
Analytical Services
-
IGC: Inverse Gas Chromatography; Understand surface energies, polarities, acid/base properties and nanomorphology on powders and fibers. ToF-SIMS: Time-of-Flight Secondary Ion Mass Spectrometry. Localize your molecules at the first nanos! 2D imaging with resolution up to 200 nm. Highest sensitivity up to 10 ppm. CM: Quarz Crystal Microbalance In-situ observation of thickness and stiffness of any films in liquid environmentSEM: Scanning Electron Microscopy Images say more than words, especially with an artistic eye XPS/ESCA: X-ray Photoelectron Spectroscopy/Electron Spectroscopy for Chemical Analysis.
-
Product
ATE & Test Systems
-
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
Product
Linear Polarization Resistance (LPR) Monitoring
-
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
Product
Probe Antennas
-
Probe antennas are offered as both standard and custom models with a rectangular waveguide interface. Probe antennas can only support linear polarization. These antennas are often used to measure the gain of other antennas by comparing the signal levels of the probe antenna and antenna under testing. The standard models operate across the full waveguide band and offer 6.5 dB nominal gain and 115 and 60 degrees half power beamwidth at center frequency. The below standard offering covers the frequency range of 8.2 to 170 GHz.
-
Product
Voltage/Continuity Tester
VOT-52
-
Standard Electric Works Co., Ltd
● Voltage test: 12V to 1000V AC/DC (8 LEDs) with indication by buzzer.● Voltage range: 12V, 24V, 50V, 120V, 230V, 400V, 750V, 1000V.● Test leads positioned at 19mm apart.● Interchangeable probe tip for 2mm and 4mm.● Polarity test : LED +/-● Audible continuity test.● Phase rotation test : /● Self-test button to ensure proper function of the device prior to testing.● Waterproof design, protection class: IP65.● Phase / Neutral identification.● Rubberized double-molded housing.● ELCB / RCD trip test.● Flashlight function.● Safety standard : IEC/EN 61010-1 III 1000V IEC/EN 61010-1 IV 600V IEC/EN 61243-3 EN 61326-1
-
Product
Twinax, Contact, Receiver, 50 Ohms
610113144
Twinax Contact (Receiver)
For increased reliability and to eliminate the need for polarization, the design of VPC’s Twinax contact consists of two concentric inner conductors for termination to a twisted pair, and an outer shield for termination of the cable shield.
-
Product
Data Diver
MT-8006B
-
LCD display for dialing number, Caller ID, Clock and other informationIndicator for determining the Line service and speedHigh impedance monitor for data safe operation without disrupting existing traffic.Smart power saving enables battery life up to 6 months12 phone number memory for speed dialing16 dialing number memoriesTone (DTMF) and pulse operationUp to 32 digits phone number memory for speed dialing keyPre-dialing and last number redial functionPBX pause key, insert a PBX pause in stored numbersTelephone line polarity indicatorsLow battery indicationBacklight functionRJ-11 port for easy test leads changeRinger and voltage LED indicationAngled bed of nails and RJ-11 plug
-
Product
1.5µm PM Ev-Yb Fiber Amplifier ( PM EYDFA )
HAPM5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM5000 is a C-Band Polarization Maintaining Optical Amplifier which worked in 1540~1570nm operating wavelength. Adopt Polarization Maintaining (PM) Multiclad Ev-Yb fiber, output optical power range 27~37dBm(0.5W~5W) ， extinction ratio >20dB.
-
Product
BNC Connectors
-
Pasternack BNC connector category includes many part numbers, most are RoHS and REACH compliant. BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC connectors are built to precise industry specifications. BNC connector items are constructed in male or female gender in standard polarity or reverse polarity threads, with 50 Ohm impedance. Connectors in BNC series are available in straight or right angle versions, as well as, 4 hole flange, bulkhead, 4 hole panel or mountless options. These BNC connector designs include clamp/solder, crimp/solder, field replaceable, solder or solder/solder attachment methods. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this BNC connector series is in-stock. Not only in stock, but these BNC connectors will ship the same-day as they are purchased.
-
Product
12-690V Voltage Tester With LED Display
7337
-
Peaceful Thriving Enterprise Co Ltd
Measurement by LED Display1. Double-pole Test2. High Voltage Indication3. Phase Rotation Test4. Polarity Indication5. Continuity Test6. Illumination
-
Product
Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A
72-8690A
-
The 72-8690A from Tenma is a dual channel general DC power supply suitable for laboratory use. The dual channel (CH1 and CH2) can work in CV or CC mode and these two modes convert automatically according to the load. The CH1 and CH2 have auto tracking function. In this condition, the output of CH2 tracks the output of CH1. This function is usually used when adjustable symmetrical and double polarity power is required. Both CH1 and CH2 display the output voltage or current with a 6 digit LED meter. The main outputs can be connected in parallel or in series. This product comes with 2 years warranty.
-
Product
Spectroscopic Ellipsometry
-
Spectroscopic ellipsometry is a surface-sensitive, non-destructive, non-intrusive optical technique widely used for thin layers and surface characterization. It is based simply on the change in the polarization state of light as it is reflected obliquely from a thin film sample. Depending on the type of material, spectroscopic ellipsometers can measure thickness from a few Å to tens of microns. It is also an excellent technique for multi-layers measurement.
-
Product
Dual Polarized Scalar Feed Horn Antenna, 24 to 42 GHz, 15 dBi
SAF-2434231535-358-S1-280-DP
-
Model SAF-2434231535-358-S1-280-DP is a dual polarized, WR-28 scalar feed horn antenna assembly that coversseveral popular 5G bands in the frequency range of 24 to 42 GHz. The antenna features an integrated orthomode transducer (OMT) that provides high port isolation and cross-polarization cancellation and a broad band scalar horn that provides low side lobe levels.
-
Product
High Frequency Current Transformer
HFCT Ø 140mm
-
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
Product
Electrical Tomography
POLARES32
-
By exploiting an innovative technology based on the use of Alternating Current (AC), the POLARES32 Electrical Tomography can measure and display all the survey parameters at the same time: ground resistivity values, current, voltage, spontaneous potential, induced polarization and indication the quality of the measurement.
-
Product
LC/MS/MS Method Package For D/L Amino Acids
-
Most important amino acids exist as stereoisomers. D- and L- forms of mirror image isomers, or enantiomers, are named according to their activity on polarized light. By using CROWNPAK CR-I(+) and CR-I(-) columns with chiral stationary phases, the D- and L-forms of amino acids can be analyzed separately. With CR-I(+) elution order is from D- to L-, and with CR-I(-) the elution order is reversed.
-
Product
JEDEC TO Collet Socket
Series 514
-
TO Collet Sockets. Aries TO sockets feature molded chamfer lead-ins for easy device insertion. High stand-off design for heat dissipation and easy cleaning. External polarization for positive location.
-
Product
Digital Display Auto Circuit Tester
1676
-
Peaceful Thriving Enterprise Co Ltd
This is a DC voltage tester with smart over-voltage protection and warning for vehicle repair. As electrical system for vehicle becomes more complex, the tester is able to test voltage value, identify DC polarity from different background light color, positive / negative sign, and over-voltage level indication. Moreover, the special designed probe is able to help user to hook, piercing, and probing the wires.
