Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
4 or 8 Channels In-Line Real-Time ARINC-Ethernet Converter
NLINE-EA429
Ethernet Interface
NLINE-EA429™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). NLINE-EA429 is a small, low-power, rugged device that provides connectivity for 1-8 ARINC 429/575/573/717 Channels – Ideal for remoting ARINC connections for in-field applications or point-point lab usage.
-
Product
ANSI X3.28 to Modbus RTU Converter
Model 2399
-
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.
-
Product
Radar Input and Scan Conversion
Cougar
-
Curtiss-Wright Defense Solutions
Cougar is an open standards-based high performance solution for capturing, converting and mixing radar video. Cougar is available as a VME card set or as part of a turnkey solution ready for deployment.
-
Product
OEM Module For Conversion Between IP And ASI
DTM-3200-RA
-
The DTM-3200 converts IP to ASI, or ASI to IP. Integrate this compact module to extend the range of I/O standards supported by your product. Technical highlights include advanced IP-jitter filtering, ultra-low latency and zero-jitter IP transmission.
-
Product
Hydrostatic
VEGABAR, VEGAWELL, VEGADIF
-
In hydrostatic level measurement, the measuring cell of the pressure transmitter detects even the slightest changes in hydrostatic pressure, which increases or decreases depending on the filling level. The acting pressure is converted into an electrical signal by the integrated electronics and then outputted as an output signal. Different types of measuring cells are used in level measurement based on the hydrostatic principle.
-
Product
High Precision Compression Type Load Cell
ZR
-
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
Product
USB / RS232 / RS485 / RS422 Opto Isolators
-
USB has now moved from the desktop to more challenging environments, including instrumentation, point of sales, factory & building automation, etc. With our rugged, industrial-grade USB isolators and USB to RS232 / RS485 / RS422 optically-isolated converters, we ensure that your assets are well protected from unexpected events.
-
Product
DC/DC Converter 2 W
R2SX-053.3/H
-
DC/DC converter with 2 W from Recom | input ranges 4.5 - 5.5 VDC | output 3.3 V | operates in ambient temperature from -40 to +100 °C | high isolation version
-
Product
Intelligent A/D I/O Unit
RAD242
-
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
Product
High-resolution Spectrometer
HR2000+
-
The HR2000+ Spectrometer integrates a high-resolution optical bench, a powerful 2-MHz analog-to-digital (A/D) converter, programmable electronics, a 2048-element CCD-array detector, and a high-speed USB 2.0 port. This innovative combination produces and extremely fast spectrometer and provides resolution to 0.035 nm (FWHM).
-
Product
Curing System by Ultraviolet-Ray
Others
-
This is the relay amplifier box for the multi-point type UV monitors. Received UV light intensity is converted to electric signal for transmission. This allows distance between the light receiving inlet and the controller to 10 meters maximum.
-
Product
PXIe Card
pi922
-
Sundance Multiprocessor Technology Ltd.
The pi922 is a COTS integration combining the flexibility of a Kintex-7 FPGA PXIe card (PXIe/700) and a 5-channels ADC with 500MS/s converters at 16-bit resolutions (ADC500)
-
Product
Web Sensor
T3511P-4
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
PMC to PCI Adapter / Carrier
PMC2PCI
-
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.
-
Product
USB Converters and Hubs
-
The C1/D2 USB converters and hubs offer industrial features like high retention USB ports, DIN rail mounting, isolation, and wide temperature ranges.
-
Product
Portable Sulphuric Acid Dewpoint Temperature Monitor
-
The fuels used in boilers, such as coal, heavy oil and natural gas, contains S. during the combustion process, S and O₂ form SO₂, and a small amount of SO₂ is converted into SO₃ under catalysis of Fe₂O₃, V₂O₅ and other catalysts. Under normal circumstances, the volume of SO₃ in the boiler flue gas is 1×10-6～50×10-6, and the water vapor is about 10%. When the temperature of the flue gas is below 200°C, SO₃ and the water vapor are completely combined into H₂SO₄ vapor. A small amount of H₂SO4 vapor will significantly increases the acid dew point. When the surface temperature of the boiler heat exchange equipment is lower than the flue gas acid dew point, the H₂SO₄ vapor will condense on the surface to become sulfuric acid solution with a concentration of about 80%, which will adhere to the surface of the heat exchanger and cause acid corrosion. Typical equipment that is prone to corrosion includes air preheaters, induced draft fans and flue walls.
-
Product
16 Channel Multievent QDC
V792N
-
The Model V792N is a 1-unit wide VME 6U module housing 16 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance). For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section. Input range is 0 ÷ 400 pC. The Model V792N features LEMO 00 connectors for both input and control signals. The outputs of the QAC sections are multiplexed and subsequently converted by two fast 12-bit ADCs.
-
Product
Quad 250Msps, 16-bit ADC FMC
ADF-Q25
-
This FPGA Mezzanine Card (FMC) converts four channels of up to 900 MHz analog input bandwidth at 250 Msps and 16-bit resolution. Based on the VITA 57 specification, the ADF-Q25 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4I.2211-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
AC Reference Generators
SR21
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
Product
Exhaust Back Pressure Tester
33600
-
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
Product
PCIe 14 Bit High Speed Digitizer - 500 MS/s on 4 Channels
M4I.4451-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
High Speed Digitizers
-
High performance and high speed digitizers with wide bandwidth and high dynamic range. Featuring high-speed Analog-to-Digital Converters (ADC) with Real-Time Field Programmable Gate Array (FPGA) based digital processors. Long acquisition memory coupled with fast PCIe offload and streaming over optical data interfaces (ODI).
-
Product
Micropotentiometers
1251
-
The BLI Series of Micropotentiometers consist of a Model 1251 terminating resistor and a Model 1351 Thermoelement housing. These micropots are true RMS current to voltage converters for calibrating AC instruments. The NIST calibration range is from dc to 500 MHz (available to 1.2 GHz)
-
Product
Optical to Electrical Converters
Optical / Electrical Converter
High bandwidth, broadband optical to electrical converters available in a range of configurations. Choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
Product
Digital Multimeters
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
Heavy duty True RMS Industrial Digital Multimeter with TFT color LCD display,providing fast A/D converting sampling time, high accuracy, built-in datalogging and TrendCapture featuresIt can trace any interrupted problems of the equipments and watch on without personIt is easy to find and solve the problems of the production equipment, providing Bluetooth technology and memory the datasheetsIt is safer measurements with double molded plastic housing design
-
Product
6 Channel Digital Receiver Module
DP-VME-5826
-
DP-VME-5826 is a VME64x Six Channel Digital IF Receiver module. It samples and down converts analog IF signals into the digital base band data.The digital base band I/O samples generated from these IF samples are pulse compressed. Down converted I/Q data is sent to the signal processor through 2 channels of 2.5 Gbps speed SFPDP link.The digital waveform generator block of digital receiver unit generates programmable polyphase coded digital pulse coded expander output.
-
Product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
-
High Voltage SCR Controlled Power Supply, P/N 18278PS Power Rating: 350 KW. Input: 480 VAC, 3 PH, 60 Hz Output: 0 to 5000 VDC, 70 Amps max Ripple: 2 % approximately at maximum rated voltage Configuration: 12 pulse externally SCR controlled rectifier system Protection Devices: Input contactors Overload relay shutoff Input surge suppressor Thermal switches Output current limiting resistor (made with 5 Ohm Kanthal heating element) Emergency power shutoff Cooling: Each 6 pulse rectifier assembly is cooled by three 10” fans Interface: 4/20 ma converter interface for output voltage and output current to SCR controller. Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier. Weight: Approx. 5000 lbs. SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack. Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configuration Rectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure. Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
Product
Turnkey or PCI Cards and Software
WinCAT Systems
-
# True fast transient recorder system.# 4, 8 or 16 channel models.# 1 MHZ aggregate 12 bit sampling, resolution equal to 0.024% of full scale.# 13 record lengths, user selected, 132 msec to 1,320 sec in typical 1-2-5x scope progression.# 6 programmable front end gains, user selected, equal to 0.4, 1, 2, 4, 10 and 20 volts full scale.# Software converts digitized voltages to Engineering units.# Digital Triggering, Amplitude and slope, in engineering units from digitized input signals.
-
Product
USB 2.0 Adapter
ADP-USB-445
USB 2.0 Adapter
The ADP-USB-445 USB 2.0 adapter converts one of the USB 2.0 headers on-board the WINSYSTEMS SBC35-427 single board computer to two type-A connectors on the front I/O panel. The integrated circuitry ensures noise immunity from the type-A connections to the single board computer and provides a robust power solution for external devices.
