Converters
Change a form or value and shows or transforms it into a different scale or value.
-
product
DCDC
DP Series
The DP family is an economically priced high performance series of regulated DC/DC converters offering single and dual outputs. Features include MOSFET design operating at a switching frequency of 100Khz, continuous short circuit protection, LC input filter, 500 Vdc I/O isolation, and an operating temperature range of -25°C to +71°C with no derating. These miniature converters maintain excellent regulation over varying line and load conditions (0.2% for line and 0.5% for load). They are packaged in an IC compatible 24 pin DIP configuration measuring 1.25” x 0.8” x 0.4” high.
-
product
Radiation Microdosimeters
Teledyne e2v HiRel Microdosimeter is a compact hybrid microcircuit which directly measures total ionizing dose (TID) absorbed by an internal silicon test mass. The test mass simulates silicon die of integrated circuits on-board a host spacecraft in critical mission payloads and subsystems. By accurately measuring the energy absorbed from electrons, protons, and gamma rays, an estimate of the dose absorbed by other electronic devices on the same vehicle can be made. The Microdosimeter can operate from a wide range of input voltages. The accumulated dose is presented to three dc linear outputs and one pseudo-logarithmic output giving a dose resolution of 14 µrads and a measurement range up to 40 krads. These outputs are intended to be directly connected to most analog-to-digital converters (ADCs) or spacecraft housekeeping analog inputs (0-5 V range), which makes minimal demands on the host vehicle. The Microdosimeter incorporates a test function to allow electrical testing of the hybrid without the need for a radiation source.
-
product
Temperature, Humidity, Bar. Pressure Transmitter
T7310
Built-in relative humidity, temperature, atmospheric pressure sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Block Down-Converter
RF Lambda’s block down-converters are used to convert higher frequencies down to IF. They can include front end amplifiers for lower noise figure and signal conditioning such as image rejection as required by the system.
-
product
Flexible MiniPCI to PCI Express Adapter
SKU-037-XX
The Flexible MiniPCI to PCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a PCI Express bus. It allows you to connect a x1 PCI Express add-in board to a motherboard that has a standard 124-pin MiniPCI connector.The adapter includes a MiniPCI host board, x1 PCIe (x4 PCIe is optional) adapter board and a PCI Express flat cable.
-
product
Flexible x1 PCI Express to PCI Adapter
SKU-041-0X
The Flexible x1 PCI Express to PCI Bus Adapter (Adapter) was designed to convert the x1 PCI Express bus into two 32-bit PCI buses. It allows you to connect up to two 32-bit PCI expansion boards to the motherboard x1/x4/x8/x16 PCI Express connector.The adapter includes a PCI adapter, x1 PCI Express host board and a PCI Express flat cable.
-
product
Precision Pressure Transducers
Precision and digital pressure transducers, somemtimes known as precision pressure sensors, convert pressure into an analog or digital signal proportional to the pressure being sensed. A precision pressure transducer (also referred to as a pressure transmitter) are used to monitor and or control sensitive pressure processes. They can also be used as high accuracy transfer standards or as a factory working standard for testing or calibrating a variety of pressure measuring instruments. With an accuracy as high as 0.008 % of reading, these pressure transducers can be found in laboratories or in production environments where a high degree of precision and accuracy are required. Each transducer is calibrated in Mensor's 17025, A2LA certified laboratory.
-
product
OEM Module For Conversion Between IP And ASI
DTM-3200
The DTM-3200 converts IP to ASI, or ASI to IP. Integrate this compact module to extend the range of I/O standards supported by your product. Technical highlights include advanced IP-jitter filtering, ultra-low latency and zero-jitter IP transmission.
-
product
PCIe 16 Bit High Speed Digitizer - 250 MS/s on 2 Channels
M4I.4420-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
LCR Meters
PeakTech Prüf- und Messtechnik GmbH
A type of electronic test equipment used to measure the inductance (L), capacitance (C), and resistance (R) of an electronic component.[1] In the simpler versions of this instrument the impedance was measured internally and converted for display to the corresponding capacitance or inductance value. Readings should be reasonably accurate if the capacitor or inductor device under test does not have a significant resistive component of impedance. More advanced designs measure true inductance or capacitance, as well as the equivalent series resistance of capacitors and the Q factor of inductive components.
-
product
COM Express Type 6 Development Kit
COM Express Type 6 Starter Kit Plus
The Type 6 Starter Kit Plus consists of a COM Express Type 6 module with ATX size Type 6 reference carrier board that offers one PCI Express x16 slot with proprietary pinout for DDI adapter card that convert DDI signal to DP or HDMI signal, one PCI Express graphics x16 slot, one PCI Express x4 slot, three PCI Express x1 slots, Serial ATA, VGA, LVDS, USB3.0/2.0, Gigabit LAN and Super I/O. All necessary cables are included.
-
product
Transition Time Converters
These converters have been designed to convert the transition times of instruments with fixed, fast transition times, to slower, fixed transition-times (150 ps, 250 ps, 500 ps, 1 ns, 2 ns); hence reducing the signal bandwidth. All transition-times are between 10% and 90% of amplitude.The design of these converters ensures very low signal reflection far beyond the 3 dB point. Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications. The converters are fitted with two SMA connectors, one male, one female.
-
product
Internet Streaming To UDP Stream Converter
ILG200
Mividi’s Internet Video Streaming to Local Broadcast Gateway (ILG200) converts the Internet video streaming using HTTP, RTMP and RTSP protocols to UDP streams for local broadcast. This product provides a simple solution for legacy CCTV network operators, such as cable and IPTV providers, to rebroadcast Internet streaming content.
-
product
Triple IC Optic Node
OX 733
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics. Green Tecnology incorporated - Aluminium Housing for maximum heat dissipation.- Frequency 40 ~ 1000 MHz- Optical Wavelength : 1290 ~ 1600 nm- Flatness ±0.75 dB- LED Bar Display for Optic Signal Level- High C/N, CSO & CTB Characteristics- Inward Extruded Aluminium Channels for Maximum Heat Dissipation- High Voltage Surge Protection- -13 dBm Sensitivity- RF O/P at 0 dBm : 113 dBµV
-
-
product
Interface and Isolation
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
product
Complete Power Analysis System
PK3564-PRO
PK3564-PRO complete Power Analysis System includes PS3550 Power Analyzer, AC charger, Quick-Start manual, deluxe voltage leads, four eFX6000 flexible current probes, SD memory card, CAS3 hard-shell carrying case, PSM-A Software, Mini Line-to-DC Converter, Bluetooth Adapter, USB Communications Cable, and 1-year deluxe warranty.
-
product
Paper Moisture Meters
A paper moisture meter measures the humidity of paper and paper products. Use of a paper moisture meter can prevent costly damages resulting from paper expansion or shrinking. A paper moisture meter determines paper moisture content based on either absolute humidity or relative humidity. Absolute humidity does not take into consideration temperature, while relative humidity relies on temperature and is expressed as a percentage of the total amount of moisture possible at the current temperature. Thus, many paper moisture meter devices feature automatic temperature compensation (ATC).For paper producers, paper manufacturers, paper mills and others in the pulp and paper industry, moisture and humidity control is essential, especially during the production process, as excessive moisture can lead to warming of the paper rolls. A paper moisture meter can be used to detect moisture streaks during the paper production process as well as to identify optimal drying times.Regardless of whether paper is stored in paper rolls in paper converting plants or stacked in sheets and paper bales in commercial printing warehouses, the porous surface of paper gradually takes in moisture relative to the humidity of the surrounding environment. This moisture can be problematic, as too much moisture can cause curling, buckling or the formation of waves in otherwise flat paper products. Moisture also can prevent inks, dyes, paints and coatings from covering and saturating paper properly during printing and processing.PCE Instruments (PCE) offers digital handheld moisture meter devices for measuring the moisture content of paper and paper products such as cardboard, paperboard, corrugated boxes, craft paper, wrapping paper, brown packaging paper, butcher paper, recycled paper, coated paper and more. Different paper moisture meter models utilize different paper moisture measuring techniques, performing moisture content tests of paper products via either destructive or nondestructive methods. Typically, a standard pinless paper moisture meter is nonpenetrating, thus allowing for the nondestructive measurement of paper water content.
-
product
Airborne Frequency Converter
AFC Series
Behlman’s AFC-7000-1 & -2 and AFC-7003, frequency converter are designed to convert three-phase aircraft power to regulated single-phase (115 or 230 VAC) or three-phase (115/200 VAC) at 50 Hz, 60 Hz or 400 Hz. They are ruggedly built to support aircraft takeoffs and landings and designed to meet the input power requirements of MIL-STD-704 and RTCA-DO-160.
-
product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
4-Channel 200 MHz A/D with DDC, VITA 49.0, Virtex-6 FPGA - PCIe
Model 78664
Model 78664 is a member of the Cobalt family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A multichannel, high-speed data converter withprogrammable DDCs (digital downconverters), it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture feature offers anideal turnkey solution. The 78664 PCIe output supports fully the VITA 49.0 Radio Transport (VRT) Standard.
-
product
TSA USB Adaptor Series
Is a hardware interface for TSA USB mini spectrum analyzer. It converts the USB interface into the RS232 interface. It is simply a command set of the TSA USB mini spectrum analyzer. It also includes the calibration calculation so that TSA USB mini spectrum analyzer can directly work on embedded system when using it.
-
product
Optical Sensor
Sendot develops and produces optical sensors that measure with light. Our optics are unique, our intelligent electronics direct the measurements and convert them into measurement results.
-
product
Synchro to BCD and Resolver to BCD Converters
TSBC TRBC
Computer Conversions Corporation
The TSB Series are miniature, high performance, continuous tracking, synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
product
Data Loggers
For acquiring temperature, pressure or fill levels, use the highly precise long-time data recording devices of the MSX-ilog series by ADDI-DATA. The compact, portable and interference-free systems are ideal for acquiring data at different locations in your installation. Data is automatically converted to physical values and can be calculated via the onboard µ-processor. The integrated web server allows easy configuration, monitoring and data export. Further features: Onboard data saving, internal clock, low consumption and Ethernet interface, data thus being available on the company network for evaluation and statistical purposes.
-
product
cPCI to PMC Compatible Adapter/Carrier
cPCIRepeat32
cPCIRepeat32 ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up one PMC card into a cPCI slot designed for bus expansion. The J2 connector can be left off for non bus expansion positions.
-
product
Gesture, Color Sensors & Proximity Detection
The gesture product family performs advanced gesture detection, proximity detection, digital Ambient Light Sensing (ALS) and color sensing (red, green, blue and clear). It also implements optical pattern generation for barcode transmission and remote controls. The gesture sensor modules provide a highly integrated solution offering five essential functions to enable a touchless interface and to optimize the end user experience of communications and consumer electronics equipment. Gesture detection uses four directional photodiodes to sense IR energy emitted from the integrated LED, converting the measurements of reflected IR light into information about physical
-
product
cPCI to PMC Adapter / Carrier
cPCI2PMC
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
product
Power Monitors
Analog Devices’ power monitoring amplifiers provide an integrated solution for digital current and voltage measurement via an on-chip, 12-bit analog-to-digital converter (ADC), communicated through an I2C interface. Leveraging ADI’s precision analog design techniques, ADI’s products are twice as precise as competing devices, offering best-in-class accuracy (<±0.8%). The power monitors complete the industry’s only monitor and sequencer family to deliver <±1% accuracy for 2 to 12 supplies.
-
product
Convertor (SCI module)
RS232/485
The RS232/485 is a self-contained device for converting RS232 signals into RS485 signals. Its simple design makes it ideal for use with all Power Management protection products in direct and modem communications. The RS232/485 converter has been discontinued and replaced by the F485 RS232/485/Fiber converter.
