Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
High Speed Free Space Optical Detectors
-
High speed optical detectors use special photodiodes with high speed electronic circuits to convert fast optical pulses to electrical signals for measurement. Unlike our optical receivers, these detectors do not include a transimpedance amplifier.
-
Product
Open Circuit Locator
A994
-
The A994 is an open circuit locator for electric and telephone cables wind on the reel; it gives the position of the fault from the inside or outside end of the cable, in percentage to the total cable length. The instrument measures the ratio of the capacitances of the two sections of failed conductor using two high precision i/v converters. The advantage of this method is due to the fact that the measurement error depends almost exclusively on the dimensional inhomogeneity of the cable. The A994 has the unique feature to permit the location of fault in cables with all broken wires. This instrument locates breaks in cables with a total capacity between 2 nF and 5 uF. The distance to fault is displayed on a large LCD display.
-
Product
Signal Isolators & Converters
-
Devar current loop signal isolators reduce problems found in field measurements when signal transmitters or converters encounter both input and output signals that may be grounded. Current loop isolators eliminate these ground loops and are available as input loop powered or output loop powered instrumentation.
-
Product
Non-Contact Type Magneto-Electric Rotation Detector
MP-9820
-
MP-9820 is a magneto-electric-rotation detector using an internal hall element, a permanent magnet, DC amplifier, and voltage regulator in its compact body. Using MP-9820 in combination with detection gear enables deriving stable rectangular waveform from ultra low speed all the way through high speed. (1 Hz to 100 kHz)MP-9820 finds wide range of applications and rotational measurement objects by using with TM-3100 series tachometer and FV-1500 FV converter.
-
Product
Dual 2.0 Gsps. 12 Bit ADC FMC
ADF-D2000
-
This FPGA Mezzanine Card (FMC) converts two channels of up to 2.8GHz analog input bandwidth at 1.0, 1.6, 1.8, or 2.0 Gsps and 12-bit resolution. Additionally, this FMC can be used in an interleaved mode to convert a single channel at 2.0, 3.2, 3.6, or 4.0 Gsps and 12-bit resolution. Based on the VITA 57 specification, the ADF-D1600 enables direct coupling of unparalleled analog-digital conversion capability with the VME/VXS/AMC/VPX/PCI-E carrier board of your choice. DEG engineers have designed this product and associated HDL firmware to work with both Altera and AMD FPGAs.
-
Product
Leeb Hardness Tester
THL210
-
LCD display of 128×64 matrix with back-light, showing all functions and parameters. Converts to all common hardness scales (HV,HB,HRC,HRB,HRA,HS). English displaying and easy and convenient menu operation. Powerful PC Software available and USB 1.0 interface and USB with Protective Membrane. 7 types of Impact Device optional, which don't need to be recalibrated when changing them. Memory of 600 groups data（impact times:32～1）. Lower limit setting and sound alarm. Material of “cast steel” is added; HB values can be read out directly when D/DC impact device is used to measure “cast steel” work piece. Printer be separated from main unit and copies of testing results can be printed as required. Normal battery AAA and big power store while USB connected and charging controlling circuit. Inbuilt function of Software Calibration.
-
Product
DC Converter
-
Primary switched DC converter modules are used, among other things, to generate different (consumer) voltage levels from central DC voltages, also battery-supported.
-
Product
DC-DC Converters
-
Electronic Test & Power Systems
The standard range of DC-DC Converters contains units with power outputs from 40W to 5kW. Small footprints, high conversion efficiencies and floating outputs are common throughout the converter range.
-
Product
BNC To Ferrule Terminal Cable, VOLT:DC 3.3V
PX0101A
Serial Cable
The Keysight PX0101A converts ferrule terminals to BNC terminal for trigger or interlock connection. It supports the Keysight M9601/02/03/14/15A.
-
Product
Total Sulfur Analyzer
Model T108
-
Teledyne Advanced Pollution Instrumentation
The Model T108 Total Sulfur analyzer is designed to measure mixed sulfur impurities, collectively referred to as Total Sulfides, in air or carbon dioxide gas. Since there is no scrubber in the system, the instrument reading is the sum of the oxidized sulfur compounds and SO2.The Model T108 consists of a modified Model T100 SO2 analyzer with special software and a Model 501TS high temperature thermal oxidizer. Sulfur compounds are heated as they pass through the converter and oxidized into SO2. When analyzing CO2, which generally contains no oxygen, approximately 6% O2 is added to the sample before entering the converter. This dilution is corrected in the calibration procedure.
-
Product
Differential Pressure Transmitter
608
-
The Dwyer Series 608 Differential Pressure Transmitters convert positive, negative (vacuum), or differential pressures of clean, dry air or other non-conductive, non-corrosive gases into a standard two wire, 4-20 mA output signal
-
Product
12-Channel VME Picosecond Resolution Time-Interval Measurement Module
V660
-
The V660 is a 12-channel time-to-digital converter used to record the time of occurrence of twelve independent electrical pulse inputs, each independently timestamped and buffered in FIFO memory.
-
Product
O/E Converter
TIA-525
-
The TIA-525 optical receiver is a convenient, easy to use optical to electrical converter. It is extremely useful in a variety of laboratory and field service situations where a quick check of the operation of a laser source, optical transmitter, or the output of a fibre optic communications link is required.
-
Product
DAQ Systems
-
Data acquisition systems (DAQ or DAS) collect information from connected sensors and other instrumentation to measure and record electrical and physical quantities, such as voltage, current, temperature, strain, pressure, shock, vibration, distance, displacement, RPM, Angle, and weight. A DAQ System typically consists of sensors, measurement hardware with signal conditioning and an Analog-to-Digital converter, and a computer with programmable software for data logging and analysis.
-
Product
Compressed Air RH+T+Tdp Sensor
T0211P-4
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Quad 12 Gsps 16-bit DAC& Quad 4 Gsps 12-bit ADC
ADF-QMx44
-
The DEG ADF-QMx44 FMC leverages the Analog Devices AD9081 MxFE (Mixed Signal Front End) transceiver technology. This highly integrated device includes a quad 16-bit, 12 Gsps sample rate radio frequency (RF) digital-to-analog converter (DAC) and a quad 12-bit, 4 Gsps rate RF analog-to-digital converter (ADC). The ADF-QMx44 features an 8-lane, 24.75 Gbps JESD204C transceiver port, an on-chip clock multiplier, digital signal processing capability and supports four transmitter channels and four receiver channels.
-
Product
Transceivers
-
Schweitzer Engineering Laboratories, Inc.
Transceivers convert between copper and fiber optics or between other communications interface standards.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Transcoder
-
Hangzhou Softel Optic Co., Ltd.
SFT3248 (SFT3248B) is a professional bidirectional trans-coder to convert video between H.264 and MPEG-2 format and also to trans-code between HD and SD programs simultaneously. It is equipped with 6 tuner inputs to receive channels directly from satellite, or ASI /IP inputs to receive digital channels. (SFT3248B is a simple version with 4 Tuners only or 4 ASI inputs only without IP input.) After trans-coding, it outputs MPTS & SPTS through the DATA port or ASI port.
-
Product
Precision Analog Anti-Alias Low-Pass Filter Board
GSAF-10
-
The GSAF-10 Gold Series are analog low-pass filter boards that offer the performance required to maintain the maximum accuracy of high-precision 16- and 18-bit A/D converters.
-
Product
PXI-7953, Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780340-01
Multifunction Reconfigurable I/O
Virtex-5 LX50 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7852 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7852 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
Hydrostatic Pressure
VEGABAR, VEGAWELL
-
The measuring cell of the pressure transducer detects minute changes in hydrostatic pressure, which increases or decreases depending on the filling level. The acting pressure is converted into an output signal by the integrated electronics.
-
Product
Development Tools
-
Acroname is your go-to source for cables, converters, servos, and relays so you can improve and expedite your development process.
-
Product
Temperature and Humidity Duct Mount Transmitter
T3413D
-
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
HD Audio Converter Board With Bracket
AX93242
-
*HD audio converter board with bracket*For SBC81205, SBC81206, SHB101 and SHB210*Mic-in/CD-in/Line-in/Line-out/Speaker-out
-
Product
Detector Switches
-
Panasonic Industrial Devices Sales Company of America
Detector Switches are used to “detect” internal mechanical movements and convert human manual operations, such as the opening of a door , to electronic signals.
-
Product
IPv6 to IPv4 Converter
-
An IPv6 to IPv4 Gateway is known by many names, including IPv4 IPv6 converter, IPv6 to IPv4 gateway, IPv6 to IPv4 network gateway, IPv6 converter, IPv6 gateway, or IPv4 converter. Some people refer to these solutions as IPv6 Compatibility tool, IPv6 compatibility appliance, IPv6 compatibility device, IPv6 transition mechanism or IPv4 to IPv6 tool.
-
Product
High Speed Digitizer
-
Is high-performance data acquisition instrument that converts analog signals into digital data at extremely fast sampling rates.
-
Product
RS232 / RS485 / RS422 / Serial To Multi-Drop Fiber Optic Converters
-
Our advanced, rugged, industrial-grade, RS232 / RS485 / RS422 serial to multi-drop fiber optic converters are designed to cover large areas. These converters support up to 255 fiber nodes, and each fiber node can extend the RS232 / RS422 / RS485's distance to 3 miles (5km) for multi-mode converters and cables, or 25 miles (40km) for single-mode converters and cables. Depending on the site situation, these multi-drop fiber optic converters can be configured as a daisy-chain or a self-healing redundant ring fiber network. When configured as a ring fiber network, the built-in self-healing feature allows the data to be transmitted clockwise or counterclockwise; therefore, failure of any individual converter will not affect other devices located on the same fiber ring, making the entire data network more robust and reliable. These multi-drop fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, and FC connectors.
-
Product
RH850 Family (Automotive only)
RH850/E1x
-
RH850/E1x microcontrollers are ideal for powertrain applications, with built-in hardware for knock control such as delta-sigma A/D converter, Digital Filter Engine (DFE), Advanced Timer Unit (ATU-IV), and Autonomous Pulse Adaptor (APA), and engine control such as fuel injection control.
