Drop Testers
determine impact resilence of packaging and products. 2) in-flight test of craft carried aloft then released.
See Also: Impact Test, Pendulum Impact, Impact Hammers
-
Product
Damp-Heat Tester
-
King Design Industrial Co., Ltd.
1. Technical index:*Power: 380V, 3-, 50/60HZ 110A*Temperature range: 50°C~120°C*Humidity range: 20%~95% RH*Accuracy: 1) temperature ± 0.3°C；2) humidity ± 2.5% RH*Uniformity: 1) temperature ± 2.0°C；2) humidity ± 3.0% RH*Uniformity test: measured at T=85°C, RH=85%; set 9 points for temperature measurement and 2 points for humidity.*Inner wall is above 50 cm; within 20 min after temperature/humidity meets the setting value, the distribution uniformity of temperature/humidity can meet the aforesaid requirement.
-
Product
Adhesion Testers
-
Instruments for measuring the adhesion of coatings to metal, wood, concrete and other substrates.
-
Product
Battery/Alternator Tester
BT55U
-
Schumacher Electric Corporation
BATTERY/ALTERNATOR TESTERFOR TESTING:• Battery state of charge• Charging system outputFEATURES:• Accurate, easy-to-read LCD screen.• Checks the battery, alternator systems• Two LED indicators• Overvoltage and Reverse Polarity Protection Contents: (1) Battery/Alternator Tester
-
Product
Line Leakage Tester
LineCHECK II
-
Designed for Automated Test ApplicationsFull Compliment of Automation InterfacesComplete Line Leakage Testing SolutionEnhanced Graphic LCDCompatible with Scanning Matrix for Patient Lead TestingContinuous Run FeatureSoftware CompatibleSafety Agency Listed
-
Product
GFCI Socket Tester
ST120
-
The Fluke ST120 GFCI Socket Tester checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120 will give you confidence on your next job.
-
Product
DMX Line Tester
DMXTSTR
-
The DMX Line Tester instantly displays the presence of +/- data on DMX lines and feed-through connectors. It serves as a perfect pocket sized tool for troubleshooting DMX512 cabling.
-
Product
Tribometers & Mechanical Testers
-
Research into materials and how materials can be changed to influence strength, integrity, or durability is an integral part of product design and improvement across nearly every industry.
-
Product
DIP Tester
Model DS-10
-
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
Product
Surge Suppressor Tester
(SST) 450
-
The ATSI SST-450 Surge Suppressor Tester is designed to quickly and easily test allcommonly used transient voltage suppressors: metal-oxide varistors (MOVs), gas-discharge tubes (GDTs), silicon avalanche diodes (SADs), thyristor surge protective devices (TSPDs), and hybrid devices.
-
Product
Battery Tester
IT5100 Series
-
IT5100 series is a series of battery internal resistance testers with high precision, high resolution and high speed. IT5100 adopts AC 4-terminal sensing, that means the tester can test internal resistance and voltage simultaneously with high precision. Resistance resolution is down to 0.1 μΩ, voltage resolution is 10 μV.
-
Product
Twist Tester
TY370
-
TESTEX Testing Equipment Systems Ltd.
Yarn Twist Tester, to determine yarn twist in single or plied yarns, quadrant type with auto stop & reverse for conventional or untwist/re-twist methods. Twist tester offers adjustable test length up to 500mm/20 inches for S & Z twist yarns.
-
Product
Mechanical Tester
-
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
Product
Manhole Impact Tester
-
Manhole Impact Tester is used to test the impact performance of manhole base and manhole wall.
-
Product
Fiber Stiffness Tester
DRK023B
-
Shandong Drick Instruments Co., Ltd.
Used to determine the bending properties of various fibers.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc., By comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit., Provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
-
Product
Battery Tester
-
Shenzhen Graigar Technology Co.,Ltd.
A battery tester is an electronic device intended for testing the state of an electric battery, going from a simple device for testing the charge actually present in the cells and/or its voltage output, to a more comprehensive testing of the battery's condition.
-
Product
Heat Seal Tester
HST-H3
-
Heat seal tester (Laboratory heat sealer) is to determine the suitable sealing parameters (sealing temperature, dwell time and pressure) for materials.
-
Product
Probecard testers
MANAGER
-
Today more complex probe cards are being used. More pins,higher density and larger array requires a new approach inprobe card analysis. With the soaring cost of new generationprobe cards, repair of defective cards becomes an necessity.BE Precision Technology offers all capabilities with the newMANAGER V. Future proof, up to 450 mm full wafer contactprobe cards can be analyzed with up to 88.000 test channels.High-end materials are used to stand extra tough requirements—such as 500 mm diameter diamante viewing window,ultra stiff carbon flip-table, high power Z–stage to generate 600Kg of contact force
-
Product
BGAN Application Tester
BAT
-
Square Peg Communications Inc.
While the BNE is tailored to the terminal development process, the BGAN Application Tester (BAT), is tailored towards application developers and provides a graphical user interface designed to simplify BGAN application testing.
-
Product
Magnetic Field Tester
MS-440
-
This device recognises fast and simply magnetic fields generated by electric reels and permanent magnets.
-
Product
Brinell Hardness Testers
-
Newage Testing Instruments, Inc.
We offer a wide range of rugged, high precision Brinell hardness testers and accessories for your Brinell testing.
-
Product
Display Tester
-
Yuyao City Yinte Neon-Electroscope Factory
This neon-electroscope is applicable for directly detection of 12-240V zero line indirect detection of DC.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
Universal Testers
-
All of our Universal Testers can be manufactured to utilize manual loading, manual loading with auto unloading, or automated load/unload. The interweaving of slip sheets between each PCB is available as well when utilizing an automated load/unload system.
-
Product
Milli Volt Drop Test Set
-
Widely used for testing transformer and switchgear, this equipment is available to clients in different capacities.
-
-
Product
Electrical Testers
-
The Fault Trapper is a new class of tester using Spread Spectrum Time Domain Reflectometry (SSTDR) to monitor energized circuits.
-
Product
Insulation Tester
-
Shenzhen Graigar Technology Co.,Ltd.
Testing the integrity of insulation requires measuring its resistance to current flow across it. A high level of resistance means that very little current is escaping through the insulation. Conversely, a low level of resistance indicates a significant amount of current may be leaking through and along the insulation.
-
Product
Dynamic Wettability Tester
6200TN
-
This is a dynamic wettability tester that uses a high-performance electronic balance to evaluate temporal changes in buoyancy and wetting (contact angle) that are successively received when various solid pieces and powder samples are immersed in liquid. Information such as dynamic and static contact angles, surface tension, and density can be obtained, and it supports various sample forms such as flat plates, fibers, and powders
-
Product
Combo Tester
750USB
-
The Staticide® 750USB Wrist Strap & Dual Heel Tester measures electrical resistance of wrist straps and heel grounders simultaneously and individually. It can also do what simple pass/fail testers cannot: store the user data and actual resistance readings to a computer. Colored LEDs and a buzzer provide universally understood test results in under three seconds.
