Organic LED
Light Emitting Diode with emissive electroluminescent layer composed of organic compounds.
-
Product
Pulsed Lasers and LEDs
-
PicoQuant's compact and reliable turn-key diode laser solutions work in picosecond pulsed, modulated, or fast-switched (nsec to µsec) operation mode. The laser systems typically consist of a common driver unit and exchangeable heads. Specialized lasers are also available as stand-alone units.
-
Product
Total Organic Carbon Analyzer
TOC-L Series
-
The TOC-L series of TOC analyzers adopts the 680°C combustion catalytic oxidation method, which was developed by Shimadzu and is now used worldwide. While providing an ultra wide range of 4 μg/L to 30,000 mg/L, these analyzers boast a detection limit of 4 μg/L through coordination with NDIR. This is the highest level of detection sensitivity available with the combustion catalytic oxidation method. In addition, the combustion catalytic oxidation method makes it possible to efficiently oxidize not only easily-decomposed, low-molecular-weight organic compounds, but also hard-to-decompose insoluble and macromolecular organic compounds.
-
Product
Integrating Sphere Spectroradiometer System for LED
LPCE-2(LMS-8000)
-
LPCE-2(LMS-8000) is an Integrating Sphere Spectroradiometer LED Testing System for identifying the performance of single LEDs and LED lamps. LED’s quality should be tested by checking its photometric, colorimetric and electrical parameters. According to CIE 127-1997 and IES LM 79-08 standards, it recommends using an array spectroradiometer with integrating sphere and photometer head to test SSL products. LISUN GROUP developed LPCE-2 test system for LED products.
-
Product
Fanless Vision System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170, Vision I/O, 4-CH PoE And 4-CH LED Output
MVS900-512-FL
-
The CAPA500 features the LGA1151 socket 7th generation Intel® Core™ processor family (codename: Kaby Lake) with 35W TDP (thermal design power), as well as the Intel® H110 chipset (Q170 optional). The CAPA500 supports one 260-pin DDR4-2400 SO-DIMM with a memory capacity up to 16GB for extensive storage. The compact 3.5-inch embedded motherboard also offers display outputs through HDMI, VGA and LVDS for triple independent display applications. Moreover, the compact-sized embedded board runs on +12 VDC power, supporting auto power-on. It can operate at a wide range of temperatures from -20°C to 60°C under active thermal control. The 146 mm x 104 mm embedded SBC is suitable for IoT/M2M-related, industrial control, self-service terminal, digital signage, POS, kiosk and many other applications where high-speed processing and graphics performance under limited space is required.
-
Product
Light Meters For LEDs
-
Photometers for the measurement of visible LEDs and radiometers for UV , visible and NIR LEDs.
-
Product
Single LED Arrays | Yellow | 2 Or 10 MA
LED-S-y-2/10
-
Pre-mounted single LED, high luminosity with low power consumption and adapt to DIN41494
-
Product
LED Floodlight up to 6000m, 120Vac 10,000 Lumen
U Light
-
The Teledyne Bowtech U light is for use on subsea platforms that operate down to 6000m depths, requiring a 120Vac Ultra- bright 10,000 lumen, LED Floodlight. The 80° wide LED floodlight beam angle is ideal for colour video inspection tasks. Housed in hard anodised aluminium, this deepwater LED floodlight measures in at 82mm Ø by 148.4mm long and comes with thermal protection ensuring that the light does not overheat if accidentally run in air. The U Light has the capability of being controlled externally by normal ON / OFF power switching or by using phase control diming techniques enabling the operator to produce a varying level of light intensity. This extremely robust U Light LED floodlight is ideal for clear visibility in deep depths on larger work class ROVs, Trenchers and Tractors.
-
Product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
-
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applications of the LEDs often operate in constant current mode and with significant thermal effects. The sophisticated LED processing industry therefore requires measurement devices that can be used for both manufacturer-compliant pulsed mode, as well as constant current operation mode. When the LEDs are run in constant current mode, the junction temperature has significant influence on the performance and lifetime of the LED. Therefore, test systems should be able to test the LEDs at specific junction temperatures.
-
Product
Voltage Tester, LED
72-9395
-
*Easy to use voltage tester designed for the professional user*Waterproof and rugged making it ideal for nearly all situations*Continuity test*690V max*Short circuit detection*Automatic range selection*Single lead voltage detection*Phase rotation test (50-60Hz)*Polarity detection*Built-in LED light*Rubberised grip*12 month limited warranty *view Terms & Conditions for details
-
Product
Switchig Power Supply For LED Products
CX-P30
-
Shenzhen Chuangxin Instruments Co., Ltd.
switchig power supply for LED productsThis serial single output switch power supply is a kind of DC regulated power supply with high efficiency and stability.
-
Product
LED Color Sensor
Smart FINN
-
With the expanding use of LEDs in electronics, a quick and effective solution to test LEDs has become more and more vital. Today, the intelligent choice is the SmartFINN™. The Smart FINN™ is the simplest method for measuring the color of an LED on the market. Smart FINN™ delivers full color and brightness readings with speed and ease. The Smart FINN™ is placed in front of the LED under test with no critical spacing or fiber-optic cables to install or maintain.
-
Product
Mini Multimode Power Meter and Mini LED Source
-
The KD Optics Mini Multimode power meter and Mini LED source are designed for the 850nm and 1300nm testing of multimode links, fibre continuity testing, connector testing, transmitter power testing etc.
-
Product
High Power LED Photo-color-semi Automatic Selector
-
Shenzhen Chuangxin Instruments Co., Ltd.
Can divide LED in to several groups by chromatic coordinates, correlated color temperature, dominant wavelength or luminous flux.
-
Product
High Power White Light LED Light Sources
LS-HP1
-
The LS-HP1 is a series of high-power, high brightness light sources for liquid light guides (LLG). It is characterized by its outstanding luminance and thus delivers very high light output from liquid light guides.The LS-HP1 works with the latest generation of high-power LEDs with up to 100W power from an area of less than 15mm² and is significantly brighter than a conventional halogen light bulb with 150W. The LS-HP1 is available for liquid light guides with core diameters of 3 or 5mm.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510A
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
Network Analyzer, Lan Tester, LED
72-6706
-
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
Product
LED Spot Type UV Curing Systems
AICURE UJ30/35
-
Panasonic Industrial Devices Sales Company of America
The compact UJ30/35 UV Curing System can be equipped with up to four individually controlled LED heads. Different types of UV-LED heads are available with an irradiation wavelength of either 365nm, 385nm or 405nm. The Controller allows for external contact inputs or PLCs for automated applications.
-
Product
High Speed LED Pick And Place
MCLEDV6
-
Assemble LED lighting products, including long tube boards and flexible strips, at rates reaching 30,000 LEDs per hour, with a high-speed, dedicated LED placer. The MCLEDV6 has a 23.6" (600 mm) max board length and includes automatic, on-the-fly full vision alignment.
-
Product
Automated LED Inspection and Testing
-
Landrex Technologies Co., Ltd.
Automated LED Inspection and Testing
-
Product
LED Drivers
-
ST offers a large portfolio of energy-efficient DC/DC powered LED driver ICs for general lighting, display LED backlighting, automotive exterior and interior lighting, RGB and monochromatic LED drivers for signage and traffic signals.
-
Product
LED Analyser
Feasa
-
Each LED Analyser allows for simultaneous measurement of up to 20 different light sources as it measures Color and Intensity – Brightness Test. Light from the LEDs is transferred by Plastic Optical Fibers and transported to the LED Analyser board for accurate measurement and analysis. The Feasa Analyser has been engineered to test LED’s and other lighting devices such as LCD Displays automatically. Intrinsic Quality offers a LED tester demo unit that can be tried out for two weeks free of charge. Currently available for purchase, call to order:
-
Product
LED Illuminator
-
Luzchem's LED-Illuminator, is a compact system for irradiating samples from 3-200 ml in size. Features a unique 7-LED design with lenses that focuses all LEDs on one spot! LEDi-KIT3 includes Luzchem's standard RGB head, comprised of two red, two green, two blue and one white LED. Or, choose from our broad range of high-powered single-coloured LEDi-Heads.
-
Product
Double LED Arrays | Bi-Color | 20 MA
LED-D-bc-20
-
Pre-mounted double LED, high luminosity with low power consumption and adapt to DIN41494
-
Product
Goniophotometer Test System For Led Lamp
1680A 1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341,the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
12" XGA TFT LED LCD Thin-Client Terminal With Intel® Atom™ Processor For Hazardous Locations Introduction
TPC-125H
-
Industrial-grade 12" XGA TFT LCD with 50K lifetime and LED backlightIntel® Atom™ E3845 1.91 GHz quad-core processor with 4 GB DDR3L SDRAM
-
Product
Monochromatic, Fiber-Coupled LED Light Sources
-
LED light sources in the LS-MC1 series provide a constantly growing selection – currently amounting to over 20 – of narrow band single wavelength LEDs with a bandwidth of 15-50 nm FWHM, allowing precise work in a defined wavelength range. As a result of optimized optical coupling into the optical fiber – as with all of our light sources – with our LS-MC1 series we have achieved the highest possible luminance. The advantage of directly emitting monochromatic LEDs is their very high level of efficiency, because the entire radiated output is in the useful wavelength range.
-
Product
LED Load Simulator
63110A/ 63113A/63115A
Simulator
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
Thermal Resistance Spectroradiometeric System for LED
TRS-1000
-
Thermal parameter is the key index to evaluate the quality of LED. Different temperature will have significant different effects on optical parameters, color parameters, electricity parameters and life of LED. Therefore, design and control of the thermal dissipation are the most important thing for the manufacturers and users. Referring to the relative international standard, TRS-1000 could conduct integration testing on optic, color, electricity and thermal, meanwhile record the changing curve of the parameters at real time.
-
Product
50-Pin DIN-Rail Wiring Board W/ LED Indicators
ADAM-3951
-
Low-cost DIN-rail mounting wiring terminal module for PCI-1752/1754/1756 with 50-pin SCSI female connectorScrew-clamp terminal blocks allow easy and reliable connectionsEach LED indicates its current bi-directional I/O logic status with either green or red lightCase dimensions (W x L x H): 77.5 x 179.5 x 41.5 mm (3.1" x 7.1" x 1.6")To Be Used With PCI-1752U, PCI-1754, PCI-1756
-
Product
LED Tester Software
Lumeresoft
-
Evolusys Technologies Sdn. Bhd.
At the heart of the software design philosophy is the ease to create test recipe amidst the dynamic range of LED packages design & test requirements. Whether it is a single die LED, multiple die LEDs, Chip-On-Board (COB) substrate, etc. the same software can be used off-the-shelf without any special customization.
