Ground
See Also: Earth, Soil, Ground Penetrating Radars
-
product
Phasing Tester
Phasing testers are used on grounded and ungrounded alternating current systems to check high-voltage fuses, test for correct phase connections and test for the absence of high voltage on de-energized lines or apparatus.
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
Isolated Analog Expansion Board
MSXB 085
The MSXB 085 Isolated Analog Expansion Board provides isolated analog inputs and isolated analog outputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
product
Type 12R2, 14U, 19" Rackmount, MIL-Rugged, Vertical
12R2-14U-V
The 14U, 12R2 was designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs.Shock isolated versions are designed to attenuate 25G shock to the chassis to less than 10Gs at the card cage and PSU tray.
-
product
PXI BRIC8 FIBO Matrix Dual 80x4 3pin brkout
40-592A-104
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
Potentiostat/Galvinostat Electrochemical Instuments
- 16 bit DAQ card- 250 kS/s aggregate- 125 kS/s per channel- Step Impedance Spectroscopy- Electrochemical impedance spectroscopy (EIS) 0.01 – 10 kHz- 5-lead cable (3 electrodes, sense & ground)- LabVIEW EZware software- Free software upgrades. 1 year parts and labor warranty- EIS information
-
product
NI-9474, 30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
779003-01
30 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9474 works with industrial logic levels and signals to directly connect to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 5 V to 30 V, features transient overvoltage protection between the output channels and earth ground, and has a LED that indicates the status. The NI‑9474 is a correlated digital module, so it can perform correlated operations, triggering, and synchronization when installed in a CompactDAQ chassis.
-
product
Conductive Footwear Tester
SLTM-1
SLTM-1 Conductive Footwear Tester checks conductive footwear automatically. The SLTM-1 Conductive Footwear Tester automatically and accurately measures the exact amount of resistance in conductive footwear and body grounding devices, ensuring a static control environment. It is ideal for dangerous, potentially explosive areas or areas in the electronic industry where static can destroy sensitive components. Stand on the foot plates and the unit’s direct-reading dial with graduated, color-coded scale indicates the exact amount of resistance. Shipped complete and ready to operate. Has 8 feet of 18-3 type SJ power cord that plugs into any grounded 120-volt AC power source. This unit measures 17 x 12 inches and weighs less than 6 1/2 lbs. All conductive footwear and body grounding devices, such as LEGSTATS, must be worn in pairs. SLTM-1 passes conductive footwear with resistance less than 2.5 MEG Ohm.
-
product
Sarsat Distress Signal Fixed Receiver
406
We propose to use Sarsat Beacon Monitor 406 in seaport services, rescue marine centers, coast guard rescue centers or GMDSS rescue coordination centers. However, this system has various prospective effective use fields. SBM 406 is a wide range ground COSPAS-SARSAT signal receiver which allows to locate emergency rescue signals sent by any 406MHz beacon in local responsibility area. The device can be connected to PC or laptop, and this gives possibility to observe distress signals and beacon position data on monitor.
-
product
NI-9263, 100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module
779012-01
100 kS/s/ch Simultaneous, ±10 V, 4-Channel C Series Voltage Output Module - The NI‑9263 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST‑traceable calibration. The NI‑9263 module includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
product
Check-Point Circuit Tester
21000
Most widely used automotive circuit tester. Quickly checks all 6 and 12 volt systems. Use with power on. 48" ground wire. Use to locate shorts, grounds and open circuits.
-
product
Software Module for Fast, Easy CMM Programming and Automation
Verisurf Automate
Verisurf AUTOMATE is CMM programming software developed from the ground up to provide a modern user experience that reduces both programming time and cycle run time. AUTOMATE requires significantly less training and experience for quality departments to immediately benefit from higher productivity.Verisurf AUTOMATE is an intelligent, object oriented programming application with an inherently intuitive and visual workflow that simplifies the most complex CMM programming.
-
product
Mission Computer Software Integration Rig
MS 1124
The HSIR is the ground test facility and it simulates various LRUs/sensors interfaced with the HAWK Mission Computer. RIG consists of Industrial computers with Simulation modules, Acquisition modules, Video generator module and video display monitors. RIG provides the simulated inputs to both the MCs from each simulated sensor/ LRU through hardwired signals, through the MIL-1553B, Arinc 429, RS-422, RS232 and Ethernet etc. The rig is capable of testing two MCs together either of which can be used as the Bus Controller (BC) or the Remote Terminal (RT). The rig provides the facility to monitor and acquire the MIL-1553B, Arinc 429, RS-422, and RS232 Ethernet bus, Analog IOs, Synchro IOs, Discrete IOs and transactions that takes place between the MCs and various sensors/units. The RIG has the capability to test individual MCs also.
-
product
3U OpenVPX 2-Slot Backplane With 1 VPX Power And Ground Plus 1 VITA 62 Power Supply Slot
101VPX302-xxxx
This 3U Open VPX backplane offers one VITA 46 Power and Ground slot and one VITA 62 power supply slot to support the development and deployment of systems requiring a VITA 62 power supply. The rear power studs can be used to connect to an adjacent backplane to feed it power.
-
product
Heavy Duty Circuit Tester for 18, 24 and 36 Volt Systems
21300
Checks AC and DC wiring up to 36 volts. Use to check series-parallel switches and solenoids on tractor-trailer starter systems. An absolute must for the trucking, farm, heavy equipment and trailer industries. 48" ground wire.
-
product
PRO Test Lead Kit
142
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
product
Third Rail Voltage Tester
4E2-1
The Knopp 4E2-1 Voltage Tester is designed to detect electrical potential (voltage) between the third rail and ground on high voltage electrified transit systems. Two, redundant neon bulbs are used to indicate the presence of voltage. The prod handle and the tester housing are both made from moisture- and oil-resistant laminated phenolic. The prod tips are made from stainless steel. The tester housing includes a rubber hand guard to guide the operator in proper placement of his or her hand. There are no exposed metal parts other than to the two prod tips. All internal connections are soldered.
-
product
Differential Probes < 1.5GHz
Differential active probes are like two probes in one. Instead of measuring a test point in relation to a ground point (like single-ended active probes), differential probes measure the difference in voltage of a test point in relation to another test point
-
product
Clamp Earth Tester with Bluetooth Connection
MET-10X
MULTI MEASURING INSTRUMENTS Co., Ltd.
Next clamp-type grounding resistance tester that can connect to a smartphone via Bluetooth and save data on an our cloud server.
-
product
SpaceWire Isolator
134
The SpaceWire Isolator is an isolation unit for ground test and integration applications, providing galvanic isolation for two SpaceWire links. Isolation is tested to 60 V with components rated to 100 V and 2500 V max transient voltage.
-
product
Linear Hall Sensor
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
product
Spark Gaps
Excelitas spark gaps are high-energy, voltage-controlled switching devices, unique in their ability to repeatedly switch currents of thousands of amperes. These devices are appropriate for use in commercial, industrial, and military ground and aerospace applications.
-
product
sbRIO-9269, Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781120-01
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The sbRIO‑9269 is a channel‑to‑channel isolated analog output module. The sbRIO‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes. Non-enclosed modules are designed for OEM applications.
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable. The LAN cable tester can verify cable continuity, open, short circuit and miss-wired. The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels. Auto and manual scan functions. Ground wire test. Lock status function. Buzzer sound warning for wire status. Display : LED indication for wire status.
-
product
Ground Earth Resistance Tester
2678X
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
product
sbRIO-9205, Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module
784787-01
Non-Enclosed, ±10 V, 250 kS/s, 16-Bit, 32-Channel C Series Voltage Input Module - The sbRIO‑9205 performs single-ended or differential analog inputs, with four programmable input ranges for each. It is an effective combination of channel count and speed at a low price for an economical multifunction system. You can choose from four programmable input ranges. To protect against signal transients, the sbRIO‑9205 includes up to 60 V of overvoltage protection between input channels and common (COM). In addition, the sbRIO‑9205 also includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. It is rated for 1,000 Vrms transient overvoltage protection. Non-enclosed modules are designed for OEM applications.
-
product
HIPOT Insulation Testers
Crown high voltage, transformer type hipot insulation testers are safe, easy to use for quick, positive determination of grounds, shorts, and broken wires in motors, transformers and other low voltage equipment or wiring systems. A turn of the selector switch gives a selection of seven voltages; 500, 1080, 1250, 1500, 1750, 2000 or 2500 volts calibrated to +/- 5% accuracy; NEMA recommendation for insulation test is twice normal voltage plus 1000 volts. Since this instrument has a capacity of 2500 volts, it readily accommodates all normal requirements.
-
product
SATCOM Antenna Positioners
CAES is a leading designer and manufacturer of custom SATCOM Antenna Positioners for military airborne, ground, and naval applications.
-
product
Virtualized Front End Processor
quantumFEP
Kratos Defense & Security Solutions, Inc.
OpenSpace quantumFEP provides the digital processing and network connectivity needed between the Command & Control (C2) system and the RF Signal processing equipment. All of the digital processing functions in a typical satellite ground system are included - command and telemetry processing, recording, AES COMSEC security, CSSDS processing, packet-level FEC, and network gateway interface support.
