Microprocessor
an IC processing logic operations to fulfill an end. Also known as: CPU
See Also: Computer, Raspberry Pi, SBC, CPU
-
product
2 PICMG® CPU, 7 PCI™, 1 ISA Slots Backplane
HPCI-9S7U
- Segment: 1- Slots: 2 PICMG® CPU, 7 PCI™, 1 ISA- Supports AT, ATX power supplies- Dimensions: 213.4 mm x 259.1 mm
-
product
RX Family Of 32-bit High Power Efficiency MCUs
RX200
The RX200 Series offers the best mix of low power consumption and improved performance in the RX Family. It delivers max. of 80MHz CPU operation with 32KB to 1MB of embedded flash memory. RX200 Series offers a wide set of peripherals, including USB, CAN, ADC, advanced security, and IEC60730 appliance safety standard support. The RX200 Series is suitable for industrial equipment, home appliances, office equipment, healthcare products, meters, and so on. Some of the RX200 Series products are tuned for motor control solutions, too.
-
product
3U VPX Development Kit
This development kit enables efficient 3U VPX backplane design and software verification.- 3U VPX architecture- One CPU blade, one GPU blade (optional), SOSA-aligned- 1TB NVMe pre-installed in CPU blade- Rear transition module(s) included- Test Frame with backplane pre-installed
-
product
Embedded System supporting FHFL dual-width PEG slot with 8th/9th Generation Intel® Core™ i7/i5/i3 in LGA1151 Socket
DLAP-4000 Series
- NVIDIA® Quadro® PEG card support- 8th/9th Gen Intel® Core™ i7/i5/i3 processor- Dual SODIMMs for up to 32GB DDR4 non-ECC memory (dependent on CPU)- 1x DVI, 1x HDMI, 1x DP (from CPU), additional display outputs from PEG cards- 1x Mini PCIe slot for Wi-Fi/Bluetooth or LTE module- 300W/500W Flex ATX PSU
-
product
Ethernet to CAN Bus Gateway
YAV90090
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
product
General Purpose Lab Oven
REXMED ROV-180
MOD. ROV-180, AC 110/230V, Plug type: , General purpose lab oven, dry air / hot air sterilizer, HS CODE: 841780, UNCCS CODE: 447483, UMDNS CODE: 14410, Main construction: powder coated steel and SS304, Controller: Microprocessor based PID controller, water proof keypad with timer, ˚C/PV and ˚C/SV display and setting, Timer: 9999/min, 9999/hr, Timer has DELAY_ON and DELAY_OFF function and at the end of operation audio and visual warning, Working range: Ambient +5˚C~250˚C, Stability at 37˚C: ±0.2˚C, Uniformity at 150˚C: ±1.5˚C, Sensor: PT 100Ω, Temperature audio and visual warning for AL-H and AL-L and OFS correction setting, Heater: 600W X 2pcs, Chamber: L40 X W40 X H50cm, Capacity: 80L, chamber with key lock, W/S: shelf X 2pcs
-
product
3U CompactPCI Serial 9-slot SSL w/ RTM w/ Ethernet
1CPCIS-309-L210
3U CompactPCI Serial Backplane with 9 CompactPCI S.0 slots, system slot left, with rear IO : 1x CompactPCI S.0 CPU slot, 8x CompactPCI S.0 peripheral slots, with connectors for RTMs (RearTransition Modules) in slots 2 to 9, Ethernet full mesh
-
product
High Power Narrow Linewidth Laser
AULLD series
Amonics' high power narrow linewidth laser (AULLD series) is integrated with Redfern Integrated Optics (RIO) PLANEXTM high performance external cavity laser. It features narrow linewidth, low phase noise, ultra low RIN, high output power with exceptionally reliable performance. The turnkey microprocessor controlled benchtop AULLD provides alarms and status indicators. An integrated RS232 or Ethernet computer interface provides easy control, diagnostic functions and data acquisition. It is particularly suitable for commercial fiber optic sensing applications, such as interferometric and Brillouin DTSS sensing systems for oil & gas, security, metrology and smart infrastructure.
-
product
Boiler Auxiliaries Plant Control Simulator
MS 1300
BAPCON SIMULATOR is used to test and validate Boiler Auxiliaries Plant Control Unit (Sigma BAPCON). It has CAN interface for simulating inputs and it is a microprocessor based system.
-
product
VPX 3U 1 Slot Chassis
HAWK
Combined with our IGUANA OpenVPX 3U switch module or Juniper Networks LN-1000 rugged router the HAWK is a very small but fully ruggedized networking platform. Combined with our 3U VPX Intel I7 CPU module it can be configured to meet various demands
-
product
Fanless Embedded System With LGA1150 Socket 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q87, 4 PoE, 6 USB 3.0, HDMI/DVI/DisplayPort And 2 PCIe Mini Cards
eBOX671-885-FL
The eBOX671-885-FL powerful industrial-grade embedded vision system features PoE (power-over-Ethernet) support. To provide better computing performance, the powerful PoE embedded vision system supports LGA1150 socket 4th generation Intel® Core™ i7/i5/i3 or Celeron™ processor (Codename: Haswell/Haswell-refresh). Its four channel Gigabit PoE ports allow multiple cabling to cameras and any PoE power device. With high-end CPU and multi-I/O connectivity, this fanless embedded vision system is well suited to multi-camera imaging applications such as optical inspection, surveillance system and IoT & M2M-related applications.
-
product
Compact 3U CPCI Single Board Computer
CP32109
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® Bay Trail platform E3800 CPU and Celeron CPU, CP32109 is a compact 3U CPCI single board computer compliant with CompactPCI® specification.On CP32109, there is a CFast interface for system installation, and several peripheral interfaces include SATAII, USB2.0 and GbE.CP32109 integrates Intel® HD Graphics display controller, and supports VGA output.CP32109 has high-performance and low power consumption, and can provide better bandwidth for data transmission. With better bandwidth, ruggedized design and extended operation temperature, CP32109 is extremely suitable for fields and applications that have high requirements on product reliability and applicability.Besides, LinkedHope® provides CP32109 with a wealth of software drivers and BSP, including VxWorks, Linux, Windows, etc., which reduce the workloads of system integrators and product developers, and greatly shorten the time-to-market.
-
product
Energy Meter Terminal
Zhengzhou SMS Electric Co.,Ltd
Meter reading terminal is such an advanced technology product, with the functions of data-collecting, processing and saving, remote meter reading, remote maintenance and software upgrade. It adopts high-performance 32 bits (ARM 9 series）CPU and Linux real-time operating system, having the characteristics of advanced design, high reliability, high compatibility, stable operation and complete functions. It is the best choice for power formula meter reading automatically, data statistics and load management.
-
product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
Vehicle Multiprotocol Interface Module
C Series
C Series Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑Rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
product
M.2 SATA SSD Carrier
SD4-SWEEP
SD4-SWEEP fits into any CompactPCI® Serial peripheral slot that is PCIe enabled. Hardware RAID operation is supported, running with an enhanced ARM-based processor to offload the host CPU.
-
product
Laser Microgage
PRO
The Microgage PRO is the next generation in laser measuring and alignment tools. Simplifying the inspection and alignment process, the microprocessor uses Smart data technology to equip its user with step by step instructions and easy to use data giving you the answers you need.
-
product
Hawk - E Co Processor
9322 E
Basic Hawk Co-Processor card set with 2.0 Mbyte memory and microcoded instructions for Nova 4X and Eclipse S280. Executes ALU instructions in 275 nanoseconds. ISA bus compatible, two slots required. Approximate CPU performance of actual S280.
-
product
Digital Pattern Generator
Wave Gen Xpress
A digital pattern generator is an essential stimulus source for almost every type of digital device: digital and mixed-signal ASIC, FPGA, microprocessors and microcontrollers. The digital pattern generator can be used early in the design cycle to substitute for system components that are not yet available.
-
product
PXI-8516, 2-Port PXI LIN Interface Module
781366-01
2-Port PXI LIN Interface Module—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver.The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
product
200KHz AUTOMATIC TRANSFORMER TEST SYSTEM
VE2729XAU
Its a Microprocessor Based 200KHz Automatic Transformer Tester with inbuilt 20 Pin Channel Scanner for Automatic Switching and Testing Coils & Transformers (Ferrite) with Max. 20 PINS. Test Parameters : -> Inductance (L)-> Leakage Inductance (Lk)-> Capacitance (C)-> DC Resistance (Rdc)-> AC Resistance (Rac)-> Turns Ratio with Winding Polaity-> Quality Factor (Q)-> Impedance (Z)
-
product
Process Ozone Monitor
Model 465H
Teledyne Advanced Pollution Instrumentation
The Model 465H is a microprocessor based high concentration ozone monitor for measuring ozone in process gas streams in water treatment, food processing, and research applications. The 465H has been designed to give accurate and stable readings over long time periods with little or no maintenance or calibration. The Model 465H is available in a NEMA 4X wall mount enclosure.
-
product
RS-485 Serial I/O
ADAM-4000/4100 Series
The ADAM-4000/ 4100 series featuring rugged industrial-grade cases are specially designed for reliable operation in harsh environments. Built-in microprocessors independently provide intelligent signal conditioning, analog I/O, digital I/O, data display, and RS-485 communication through Modbus RTU protocols.
-
product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB112
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot, one PCIe x16 slot, and ten 32bit/33MHz PCI slots
-
product
Viscometer
LS
Chongqing Lushun Scientific & Technological Development Co., Ltd.
This instrument is sophisticated. It adopts advanced mechanical design and manufacture techniques, and microprocessor controlling technologies, it can accurately collect test data; Take a blue background light, ultra-brighten LCD as its display, so it can display test data intuitively; Designed with a RS232 port, so it can print out test data through a printer, and it can communicate with a computer using the software attached. It is sensitive, reliable, beautiful and convenient to be operated. It is used to determine absolute viscosity of Newton liquids and apparent viscosity of non-Newton liquids. It can be widely used for determining viscosity of grease, paint, plastic, medicine, dope, adhesive, and washing solvents, etc.
-
product
40-Pin DIP-to-Socketable PLCC Adaptor
1111163
40 Pin DIP to Socketable PLCC Adapter. Can be used with Intel 80/83C652 and 80C251 microprocessors and any IC that follows standard DIP to PLCC pinout conventions. Allows user to switch package styles and avoid shortage problems. Designed to plug directly into your 44 pin PLCC socket.
-
product
6U CPCI Processor Board
CP62101
LinkedHope Intelligent Technologies Co.,Ltd.
CP62101, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM67/HM65 platforms supporting 2nd generation Intel i series CPU, up to 2.5GHz frequency, HD3000/2000 integrated core graphics and dual-channel SO-DIMM memory (800 /1066 /1333) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62101 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048 × 1536. Besides, CP62101 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
product
FireBird Camera Link Frame Grabber (2xCLM-2PE8)
AS-FBD-2XCLM-2PE8
FireBird is designed for ultimate performance using Active Silicon’s proprietary DMA Engine technology, “ActiveDMA”. This technical innovation applies RISC based processor techniques and guarantees zero CPU intervention, high-speed and low-latency image data transfers.
-
product
Oxygen Bomb Calorimeters
Labodam oxygen bomb calorimeters are designed with high precision sensors and microprocessors to get reliable and accurate results. They are designed and made as per the International Standards ASTM D5865-13 Test Methods for Heat of Coal, ASTM D240-17 Test Methods for Calorific Value of Petroleum Products, and ASTM D4809-13 Oxygen Bomb Calorimeter.
-
product
DC DC Converter Models
These versatile DC-DC Converters are ideally suited for powering a wide variety of analog and digital circuitry, such as op amps, logic and microprocessors. They may be mounted directly on a printed circuit board for OEM applications, or installed in a socket for developmental and small quantity requirements.
