-
Product
Interactive Software
TE SERIES
-
The TE SERIES Interactive Software provides a powerful set of formats and charts for fast analysis, and interfaces with a simple USB. Features include smith charts, multi series plotting, difference plotting, curve smoothing, annotations, cursors, time domain reflectometry and interference spectrum scanning.
-
Product
Audio Line Drivers and Receivers
-
Analog Devices audio line driver and receiver solutions feature differential-output buffer amplifiers and differential input buffer amplifiers to support a wide range of applications. By using low noise thermally matched thin film resistors and high slew rate amplifiers, these parts maintain the sonic quality of audio systems by eliminating power line hum, RF interference, voltage drops, and other externally generated noise commonly encountered with long audio cable runs. Applications involving this product portfolio include ADC drivers, high performance audio, sine/cosine encoders, and other professional and consumer uses.
-
Product
HBM Verification Tester
HBM-VT
-
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
Product
Flash SATA Disk/mSATA Mini SATA 3 SLC, MLC
FSA 301 Series
-
*SATA III (6.0Gb/s) interface*Capacity: SLC 1 GB to 32 GB, MLC 4 GB to 64 GB*iSMART disk health monitoring*Intelligent error recovery system*Write protection security*Anti-vibration mechanical design*Excellent data transfer speed*Zero mechanical interference*JEDEC standard MO300B dimension
-
Product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
-
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
Product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
-
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
Product
Electromagnetic Environmental Effects
EEE
-
Electromagnetic Environmental Effects Services provides engineering design and test implementation for Electromagnetic Interference and Compatibility (EMI/EMC), along with TEMPEST capabilities certified under the National Security Agency (NSA) TEMPEST Endorsement Program.
-
Product
Modulation Distortion Up To 43.5 GHz
S930704B
-
S930704B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 43.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Handset Noise Under RF Test System
BK8021
-
If you need to evaluate the resistance of cellphones to RF interferance, the BaKo Type BK8021 Handset Noise Under RF Test System is what you need. It performs four tests to evaluate the Sending Noise, Sending Sensitivity, Sending Loudness, Sidetone Masking, Receiving Sensitivity and Receiving Loudness. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When testing is complete, you can print the data as an MS Excel report or save it for comparison and analysis.
-
Product
Modulation Distortion Up To 90 GHz
S930709B
-
S930709B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 90 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930709B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Sapphire polariscope optic modulator
PKS-250M
-
The device is designed for determining double refraction in flat blanks and products of transparent and weakly tinted materials, and is used for quantitative assessment of double refraction value by Senarmon method with an error of not greater than 10 nm, for assessment of double refraction distribution in an object by interference tinting, for examining distribution of double refraction in an object with circularly polarized light.
-
Product
One Port Vector Network Analyser
TE3001
-
The TE3001 One Port Vector Network Analyser is built for the professional who understands the calibration process and has a network analysis task to perform. The unit features a larger output signal than the TE3000 for better noise immunity, and is supplied with a 6 piece custom calibration kit to remove the effect of test fixtures and cables. Together, these features make the TE3001 ideal for broadcast and plasma applications that require a length of cable for connection and may be high in noise or interference.
-
Product
Integrated Modular Electromagnetic Modeling Suite
EM.Cube
-
EM.Cube® is an industry-recognized simulation suite for electromagnetic modeling of RF system engineering problems. It features several distinct simulation engines that can solve a wide range of modeling problems such as electromagnetic radiation, scattering, wave propagation in various media, coupling, interference, signal integrity, field interactions with biological systems, etc. Using EM.Cube, you can solve problems of different sizes and length scales, varying from a few microns in MEMS devices to several miles in large urban propagation scenes.
-
Product
Detectors
-
Solar blind detector for operation in the 1 to 180 nanometer region. It is encased in a vacuum tight housing for vacuum operation. The Model 425 is ideal for measurements in the Extreme and Vacuum UV (EUV and VUV) where the solar blind feature eliminates potential interference from long wavelength ultraviolet and visible light. It may be operated in pulse-counting mode or DC. The CEM is also available with coatings like Cesium Iodide or Magnesium Fluoride to enhance response in different energy regions.
-
Product
15 Amp 120 VAC Filter and Surge Arrestor
AS-AC15
-
- 15 amp 120VAC quad outlet for high power devices- Resettable circuit breaker protection, easy to use and reset- I EA standard input plug and #14 GA AC line cord for USA - standard interface- MOV surge arrestors included - for even more protection- High level of common mode and differential mode filtering digital noise and RF filtering eliminates- digital artifacts and RF interference - See chart- Front Panel Neon Blue AC ON indicator - just plain cool to look at, not too bright!- Double shielded box inside - for optimum filtering operation- Size 6W X 4H X 4 3/4 D in inches approx 3 lbs
-
Product
Zero Air Generator
AQMS-100
-
The AQMS-100 generates clean and dry zero air by removing components which will cause interference on zero point calibration.
-
Product
IC Tester
ICE1
-
The IC Test System was developed to measure the EMC behavior of circuits (ICs) in the event of targeted field or line-related interference and for measuring emissions. The test IC is tested in function. The test environment ICE1 creates the functional environment of the test IC. The respective measurement task is carried out with the corresponding probe set.
-
Product
Flash SATA Disk /mSATA SATA 3 SLC,MLC
FSA 300 Series
-
*SATA III (6.0Gb/s) interface*Capacity: SLC 1 GB to 64 GB, MLC 4 GB to 128 GB*iSMART disk health monitoring*Intelligent error recovery system*Write protection security*Anti-vibration mechanical design*Excellent data transfer speed*Zero mechanical interference*JEDEC standard MO-300B dimension
-
Product
Split Type Ultrasonic Level Gauge
HR9100D
-
HighReach Measuring & Controlling System Co.,Ltd
1. Stable and reliable / We select high-quality modules and key components from the power supply part to select high-stability and reliable devices, which can directly initiate imported instruments. 2, patented technology / one ring patented sound wave intelligent technology software can Intelligent outgoing analysis without any debugging and other special steps, this technology has the function of dynamic thinking, dynamic analysis 3, high precision / sound wave intelligence owned by our company The patented technology greatly improves the accuracy of the ultrasonic level gauge, the Liquid level accuracy reaches ±0.2%, can resist various interference wavesThe instrument is a non-contact instrument, not Direct contact with liquid, so the failure rate is low. The instrument provides a variety of installation methods, users can use this . The Instrument Manual Calibrate to 5. The Protection of The Level of Multiple Protection / IP67 & Instrument Reaches; INPUT and Output Lines All have have Lightning Protection and Short Circuit Protection.
-
Product
Laser Doppler Vibrometer
LV-1800
-
The LV-1800 non-contact type Laser Doppler Vibrometer uses newly designed interference optical system and has achieved improvement of detection sensitivity by 20 dB compared to the conventional models. The built-in positioning camera makes it easy to check the target by laser beam irradiation.
-
Product
Antenna Test Chamber for Automotive Radar
ATS1500C
-
The R&S®ATS1500C radar test chamber is a compact antenna test range (CATR), consisting of a gold-plated parabolic reflector and a two-axis positioner for 3D movements of the radar module. Combined with the R&S®AREG800A target simulator and other Rohde & Schwarz test and measuring instruments, it can be used for a variety of applications, including antenna characterization, module calibration, RF performance validation, interference testing or in-band compliance testing. The chamber is equipped with a universal feed antenna which gives access to both polarizations in parallel. Automated temperature testing over the range of -40 to 85°C is possible with an optional enclosure.
-
Product
VXG Vector Signal Generators
-
Keysight's VXG vector signal generators offer the industry's highest output power with ultra-low phase noise for your most demanding wireless and aerospace and defense applications. With the VXG's multichannel architecture, quickly switch from blocker and interferer tests to MIMO and beamforming tests.
-
Product
Modulation Distortion Up To 53 GHz
S95070B
-
S95070B software enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 53 GHz. The wide dynamic range and vector error correction of the PXI VNA results in an extremely low residual EVM from the test setup, giving you a complete picture of your device’s performance without test system interference. S95070B software measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals through spectral correlation between the input and output spectrum, without doing demodulation. Integration with the PXI VNA’s measurement flexibility enables you to do quick modulation distortion measurements along with traditional VNA tests.
-
Product
Gas Filter Correlation CO Analyzer
Model T300U
-
Teledyne Advanced Pollution Instrumentation
The Model T300U Trace-level CO analyzer has been developed specifically to address the challenges of low level monitoring as required, for example, in the US NCore network. Using IR absorption with a Gas Filter Correlation Wheel, the T300U is designed to allow ultra-sensitive CO measurements while still meeting the requirements for use as a US EPA compliance analyzer.The optical bench is enclosed in a temperature controlled oven, dramatically decreasing instrument noise and drift. The objective and field mirrors in the sample cell are gold plated to maximize signal to noise performance, while a temperature-controlled Nafion dryer on the inlet minimizes water interference caused by ambient humidity changes. Periodically, the T300U seamlessly corrects its baseline by routing the sample through a heated catalytic CO scrubber. This Auto Reference function corrects zero drift and reduces the effect of interferences.
-
Product
Control Board for Motor, Pump & Valve
F1V04
-
Beijing SANKI Petroleum Technology Co., Ltd.
The main board issues a start signal and a low voltage signal (12v) for opening the electromagnetic valve, which are converted into strong voltage signals (220 VAC) to drive the electromagnetic valve (380 VAC) and the motor in our fuel dispensers system, thus completing the function of conversion from weak voltage power to strong voltage power. The control board circuit isolates high voltage interference signals via photoelectrical isolating components.
-
Product
PXI Vector Signal Analyzer
-
PXI Vector Signal Analyzers feature a wide frequency range, real-time signal analysis, and advanced signal processing. PXI Vector Signal Analyzers can perform measurements for a broad range of wireless technologies such as GSM, EDGE, WCDMA, LTE-Advance Pro, 5G, Wireless LAN, and Bluetooth. Select models also feature a LabVIEW-programmable FPGA that you can customize for advanced measurement applications. PXI Vector Signal Analyzers are ideal for microwave test, wireless test, RADAR test, spectral monitoring, software-defined radio (SDR), radio monitoring, interference detection, signal intelligence, and other applications.
-
Product
Portable Monitoring Receiver
PR200
-
The R&S®PR200 portable monitoring receiver is engineered to effectively support spectrum monitoring, interference hunting, spectrum clearance and site testing. It reliably detects, analyzes and locates signals from 8 kHz to 8 GHz and can be extended up to 20 GHz with the R&S®HE400DC handheld directional antenna and up to 33 GHz with the R&S®HE800-DC30 handheld directional antenna both with an integrated downconverter. Optimized for field operations, the R&S®PR200 provides a perfect balance between RF performance, speed and operability, while offering a range of measurement functions suitable for complex 5G signals.
-
Product
IEC 61000-4-5 EN61000-4-5 Lightning Surge Tester, Surge Generator
506AX
-
Shenzhen Chuangxin Instruments Co., Ltd.
Automatic lightning surge generator (or Lightning surge immunity) is used to assess the power cord and connect the internal switch stood in line to connect the internal switch to provide a common basis for switching the natural world and lightning caused by the high-energy transient interference performance. Performance fully meets the IEC 61000-4-5, EN61000-4-5 and GB/T17626.5 standards.
-
Product
Spectrum And Signal Monitoring
-
Kratos Defense & Security Solutions, Inc.
With the rapid growth of satellite networks including VSATs, there is the potential for increased Radio Frequency Interference (RFI). Interfering signals can be periodic or occur at different frequencies over time, making the discovery and removal of these sources a significant challenge.
