-
Product
Rectal Probe For Rats (Isolated)
RET-2 ISO
-
• An isolated sensor (can be used with monitoring equipment where electrical interference from other electrodes may be present).• Reinforced strain relief for applications where probe is in more frequent use.• Smooth ball tip. Stainless steel shaft - '' long, .059'' diameter. Tip diameter .125'', 5 foot lead length. Time constant 0.8 seconds.
-
Product
Blockage Locators
-
Shenzhen Noyafa Electronic CO.,LTD
Noyafa Blockage Locator can be used in both household and engineering. The sensing range is enhanced, and it is free from external interference. It can pass through the 60cm-thick cement wall and the pipe blockage under the floor to reduce the removal area. Accurate detection and adjustable sensitivity.
-
Product
Lightning Surge Generator
STT-LSG-7K16A
-
Beijing KeHuan Century EMC Technology Co,.LTD
The lightning surge generator STT-LSG-7K16A provides a common basis for evaluating the performance of equipment power lines and internal connecting lines when they are subjected to high-energy transient interference from switching and natural lightning strikes. The performance meets the requirements of IEC61000- 4-5 and GB/T17626.5 standards.
-
Product
High Voltage Differential Probe
DP750-100
-
Shenzhen Micsig Instruments Co., Ltd.
*The leads and probe are with shielded design, interface ends are integrated in a compact box, no need to twist the cables, leads to a lower noise floor and has less interference. *Support one-press Zero calibration and automatic overrange alarm.*Directly powered by Micsig UPI interface, realise auto scaling setup, can also powered by oscilloscope via USB cable.
-
Product
Micro Spectrophotometer
USPM-RU III
-
The USPM-RU III is a reflectometer that provides highly accurate spectral reflectivity measurements of small, curved, and thin samples without interference from rear surface-reflected light. The curved surface of the lens can be measured from a minute spot as small as ø60 µm formed on the sample surface. This provides the ability to use a goniometer to examine even the curved side lenses or other optical component.
-
Product
Cell Stand
CS-3A
-
The CS-3A Cell Stand is adopted with CHI series Electrochemical Analyzers and other apparatus directly. The cell is enclosed in a Faraday cage to reduce electrical interference. A built-in gas control allows purging a sample. Gas line is provided to purge next sample, while analyzing the present sample separately, thus increasing productivity. Magnetic stirrer allows for controlling the mixing of the sample for experiments requiring mass transport of electrolyte or analyte to the electrode surface. Cell top positioner with detachable cell cap allows easy removal and replacement of the cell vial as well as the electrodes for rinsing, cleaning, and replacement.
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
Product
Logarithmic Periodic Broadband Antennas
-
Directional, active broadband antennas that are the ideal solution for interference tracking, site surveying, and most general RF and EMC analysis applications, due to their unique dipole elements positioned along the antenna axis in a triangular shape.
-
Product
RF Acquisition Record and Playback Instrument
SARP-6
-
Saluki SARP-6 RF Signal Acquisition Record and Playback Apparatus is a portable RF signal acquisition record playback equipment. It can be used to directly acquire, record, and playback RF signal from 1MHz to 6GHz. Its data recording and bandwidth playback can reach 200MHz. The SARP-6 RF Signal Acquisition Record and Playback system is composed of up and down inverter module, high-performance ADC and DAC, and large capacity solid-state FLASH or high-performance disk. It is widely used in radar, GPS, communication, telemetry, as well as many other circumstances for civil purposes when acquiring signal and recording it down.Applications: Interference Analysis/Surveillance/Spectrum Management/Satellite Communications
-
Product
EMC Testing Inductors
-
Electromagnetic Compatibility (EMC) testing is a somewhat unique discipline within the world of electrical product development and analysis. Electromagnetic Compatibility (EMC) testing is primarily concerned with understanding and mitigating the affects of Electromagnetic Interference (EMI).
-
Product
Filter Probe
350
-
AINES 350 NFP is a professional noise filter probe to use in a demanding environment. It is designed to make a technician's job easy while tracing a wire from a bunch of wires with electrical interferences. The 350 NFP is the best option for technicians compared to other available products in the market. Combined with the AINES 140 or 240 Tone Sets, the 350 NFP makes a formidable combination to identify a cable pair quickly and conveniently in a normal environment and in locations with electrical interferences as well.
-
Product
HBM Verification Tester
HBM-VT
-
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
Product
ISI Channels
M8048A
ISI (Intersymbol Interference) Channel Board
The M8048A ISI channels offer a choice of eight differential traces to emulate channel loss in a high-speed digital receiver test setup.
-
Product
Photolytic True NO2/NO/NOx Analyzer
Model T200P
-
Teledyne Advanced Pollution Instrumentation
The Model T200P provides measurements of NO and NO2 using our Model T200 NOx analyzer combined with a patented high efficiency photolytic converter. Even low temperature molybdenum converters transform other nitrogen-containing compounds such as HNO3, PAN, etc. to a considerable extent. Simultaneous measurements of NO2 performed with molybdenum and photolytic converters have shown significantly different results in the presence of such compounds.In the photolytic process the sample gas passes through a cell where it is exposed to light at a specific wavelength from an LED array. This causes the NO2 to be selectively converted to NO with negligible interference from other gases. Advances in the photolytic converter technology now yields NO2 conversion efficiency that is similar to molybdenum under typical ambient NO2 concentrations, but without the same interferences.
-
Product
Rectal Probe For Mice (Isolated)
RET-3 ISO
-
• An isolated sensor (can be used with monitoring equipment where electrical interference from other electrodes may be present).• Reinforced strain relief for applications where probe is in more frequent use.• Smooth ball tip. Stainless steel shaft - 3/4'' long, .028'' diameter. Tip diameter .065'', 5 foot lead length. Time constant 0.5 seconds.
-
Product
Wavefront Modeling And Simulation
-
The CAST-CRPA Simulation Systems provide a precise, coherent, and repeatable GNSS RF signal “wavefront”, that is a perfect solution for testing phased array, or “CRPA” antenna systems, in a laboratory environment. The system generates a complete set of RF signals for each antenna element, which are referenced to the phase center of the antenna manifold. In addition, the CAST system allows users to add interference and IMU signals that can also stimulate EGI’s and a wide range of modernized navigation devices.
-
Product
Desolvating Nebulizer
Aridus3
-
The CETAC Aridus3 Desolvating Nebulizer System is a specialized liquid sample introduction accessory for inductively coupled plasma mass spectrometry (ICP‑MS). The Aridus3 can enhance analyte sensitivity up to 10 times or more and can greatly reduce solvent-based interferences such as oxides and hydrides.The Aridus3 couples a low-flow (50, 100, or 200 µL/min) PFA nebulizer and a heated PFA spray chamber with an inert fluoropolymer membrane. This combination provides enhanced analyte sensitivity while reducing solvent based interferences such as oxides and hydrides. The Aridus3 is particularly advantageous for small volume and highly corrosive samples such as those generated in the earth sciences and the semiconductor industry.
-
Product
XYZ Color Sensor
AS7261
-
Calibrated XYZ color sensor provides complete, integrated platform for handheld color analyzers, color calibration and mobile analysis devices. Tri-stimulus XYZ realized by silicon interference filters. UART or I²C slave digital Interface. 16-bit ADC with digital access. Programmable LED drivers. 20-pin LGA package 4.5mm x 4.7mm x 2.5mm, with built-in aperture. Compact true-color sensing. Applications; Color/CCT sensing, Fluid or reagent analysis, Color point comparison, Display calibration.
-
Product
DC Voltage Generator
MON8P
-
Mezzanine MON8P is designed to generate DC voltage in the range of ± 10 V through eight galvanically isolated channels from each other and from the case, which allows to reduce the level of interference and increase the safety of the device.
-
Product
Monics SatGuard
-
Kratos Defense & Security Solutions, Inc.
SatGuard can help resolve in minutes, revenue loss problems that have lasted weeks, months or longer. The VSAT monitoring and mitigation product from Kratos classifies VSAT networks and identifies the specific IDs of the terminals causing interference to much more quickly resolve issues.
-
Product
Spectrum Monitoring and Interference Systems
-
Automate wide area, close-proximity signal monitoring, interference detection, identification, location, reportingIncrease flexibility; set up rugged, portable-RF sensors in fixed, temporary or mobile platforms in any environment for extended periods of timeRemotely deploy a single sensor or a network of sensors synchronously country or city-wide, or in a roomCustomize for your application with software for spectrum monitoring, emitter location, signal intercept, capture/analysis
-
Product
Inverted Microscopes
-
ACCU-SCOPE inverted microscopes deliver excellent ergonomics, top quality optics, crisp images and configurability to meet your needs. The “workhorse of the tissue culture lab,” the inverted microscope is found in practically all tissue culture rooms and is used to observe cells in culture for their health and growing condition. Living cell cultures are essential to the discovery of cellular processes, providing scientists insight into mechanisms of disease that can be used for identifying new therapeutics. ACCU-SCOPE inverted microscopes are commonly equipped with phase contrast components for the observation of living cells in culture without the need for staining. Other available contrast methods may include brightfield, fluorescence, emboss, differential interference (“DIC”) and modulation.
-
Product
ISI Channel Boards
M8049A
ISI (Intersymbol Interference) Channel Board
The M8049A ISI channel boards can be used to emulate channel loss in receiver test setups. The boards are used to emulate channel loss for data rates of 32 Gb/s and higher. A choice of 21 PC board traces with different lengths can be inserted into the signal path. The trace lengths range from 0.8 inch (20.3 mm) to 22.3 inch (566.4 mm). By cascading the traces within one board or with another board, a wide range of channels can be emulated with very fine resolution of insertion loss steps. With their small size the ISI channel boards can be located closely to the device under test.
-
Product
Receiver, ICon EMI , With Protective Cover And Strain Relief
310123102
Receiver
Includes all of the standard features of the iCon, in addition to Electro-Magnetic Interference (EMI) protection. An earth ground terminal is included on the and a "mate first, break last" feature connects the earth ground circuit. The earth ground terminal on the strain relief prevents user shock and injury.
-
Product
EMC Products
-
Products for demonstrating the electromagnetic compatibility of devices (EMC), i.e. for investigating inadvertent high frequency emissions that can interfere with other equipment as well as the immunity to irradiation that could interfere with a device.
-
Product
Aerospace
-
Radiometrics Midwest Corporation
Working with the Radio Technical Commission for Aeronautics, Radiometrics staff has not only been involved with EMC testing of aircraft and aircraft components, but has also been involved with development of the RTCA/DO160 "Environmental Conditions" standard and RTCA/DO-199 investigation for "Potential Interference to Aircraft Electronic Equipment from Devices Carried Aboard".
-
Product
Ring Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
Product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
-
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
Product
Acoustic Emission Preamplifier
-
The Acoustic Emission Preamplifier is a instrument designed specifically for use with acoustic emission sensors, which is used to boost the signals and filter out any noise or interference. With its advanced technical features and robust design, the QingCheng Acoustic Emission Preamplifier is the perfect choice for professionals seeking a high-performance acoustic testing solution.
-
Product
4-20mA Output Inclinometer
LCF-2330
-
The LCF-2330 inclinometer series now includes a 4-20mA output signal option for applications that require long cable runs. This dual axis tilt sensor is fluid damped to minimize noise and vibration interference while also offering a sharp 1 µradian resolution. An internal temperature sensor is available and dual supply, ± 5 Vdc output is an option. The LCF-2330 is an excellent solution for rugged applications such as radar & antenna leveling, weapons platform leveling, barge and offshore platform control, deviation surveys, 2-axis machine tool leveling, bridge structural monitoring, submersible control feedback, offshore platform stability and manufacturing process equipment for the aerospace industry.
