Suppression
-
Product
Compton Suppression Counting Systems
-
Compton-Suppression Systems are used to reduce the background continuum for low-background counting, thus improving the Minimum Detectable Activity and overall spectrum quality – particularly for small volume samples such as air filters and petri dishes.
-
Product
Noise Suppression Products / EMI Suppression Filters / TVS Diodes (ESD Protection Devices)
-
Murata noise suppression products include compact EMI suppression filters that efficiently eliminate noise, L Cancel Transformers (LCTs) that greatly suppress noise in high-frequency bands by reducing the ESL generated inside capacitors and in boards, and TVS Diodes that guard semiconductor devices against electrostatic discharge from external sources. Murata supplies products that support a variety of approaches to suppressing noise.
-
Product
Darlington Arrays
-
Darlington devices are high-voltage, high-current switch arrays containing multiple open-collector Darlington pairs or multiple Darlington transistors with common emitters, and integral suppression diodes for inductive loads. The nominal current rating of each output is 500 mA for the 7- and 8-output devices and up to 1.5 A for quad-output devices. The inputs are pinned opposite the outputs to simplify the application board layout. These devices interface standard logic families.
-
Product
120 A High Voltage 50 Ω Pulse Generator
TLP-12010C
-
High Power Pulse Instruments GmbH
- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
Product
C-Band DWDM VGA without Mid-Stage Access Next-Generation Variable Gain EDFA
HWA4500 (With SNMP)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4500 series is a next-generation variable gain EDFA, which with the most excellent performance and most completes functions in the market. It adopts nowadays most excellent optical performance, most advanced electronic technology and most complete software functions. Remarkable transient suppression control technology and heat management control technology let many complicated optical functions achieved. It is the most versatile multifunction optical amplifier in the market.
-
Product
LAN Cable Tester Plus
PK-3456 Spy Splitpair
-
Easily & accurately tests twisted pair cables for proper continuity and correct signal pair. A split pair can cause a crosstalk problem and suppress the communication speed. The SpySplitpair also includes a Full test, One-ended testing, Debug mode for checking the specific pair fault, and a Tone mode for tracing cable as well as a Voltage warning indicator to protect the tester. Hub blink/Net Tone mode (PK-3456E only), display of the Ethernet port to which the test cable is connected, and identify unknown RJ45 outlet for active Ethernet.
-
Product
Ancillary Test Cell Products
-
In addition to our innovative and industry leading AccuDyne AC Dynamometers and DynoLAB Test Automation Systems, SAKOR fully integrates a complete range of ancillary products and subsystems necessary for an advanced test cell. Examples include:*Combustion air consumption measurement and conditioning subsystems*Exhaust handling systems*Fuel consumption measurement and conditioning subsystems*Coolant and oil conditioning systems*Throttle actuators*Spark/Fuel controls*Combustion analysis systems*Complete exhaust emissions analysis systems (per 40 CFR 1065 regulations)*Sound attenuating (up to STC 52) test cell enclosures with several fire suppression options*Process water evaporative cooling tower
-
Product
Innovative Multiple - Object Tracking Radar
iMOTR
-
We have advanced the multiple-object tracking radar concept with an innovative application to meet today’s test range needs. The iMOTR features enhanced clutter suppression capabilities to deliver clearer, more accurate assessments of object launch trajectory and flight path data on airborne and low flying objects. This tracking information can then be handed-off to other radars or data collection sensors in real-time. The system is also better equipped to provide precision time, space, and position information (TSPI) data of multiple objects in flight over a wider field of regard than the current test range radars in service.
-
Product
Automatic Capacitance and Tan Delta Bridge
-
*Automatic Microprocessor controlled Guarded Bridge Circuit.*Suitable for testing at voltages up to 500kV.*Can be used to measure both Grounded and Un-Grounded Specimens.*Automatic guard circuit for three-terminal measurement.*Interface measurement and automatic interference suppression circuitry.*Optional range Extension Transformer for large capacitance values.*Test data storage facility.*RS-232 computer interface and USB printer interface.*Window Interface Software for data transfer.
-
Product
Anti-Drone System
-
Shoghi’s Anti Drone System is Mil-Grade All weather Drone Jamming system, designed for 360 Deg Auto Detection, Triangulation and Neutralization of Single or Swarm of UAVs/Drones with an Enhanced Detection and Jamming Range. The system comes with a 360 Degree built-in radar for detection of the UAVs/Drones from 3 -50Km range with an Azimuth of 60 Deg. Such a High Detection and Suppression Range enables the operators to create a larger security perimeter with continuous monitoring of any Intrusion.
-
Product
Frequency Doublers
-
Teledyne RF & Microwave offers several Frequency Doublers providing high fundamental suppression, broadband input/output frequencies, and low conversion loss figures for a variety of communications applications.
-
Product
Real-Time Waveform Averaging Firmware
FWATD
-
The Advanced Time-Domain firmware option, FWATD, equips the ADQ7 and ADQ14 digitizers with advanced tools for sophisticated time-domain measurements. Multiple steps of noise suppression is provided in order to achieve extreme dynamic range, so that rarely occurring weak signals can be detected and distinguished from noise.FWATD can track and correct for temperature-dependent baseline (DC level) fluctuations, which may otherwise lead to incorrect detection or even detection of false pulses. It supports several types of noise reduction for both random and systematic noise. The flexible architecture and user-defined settings enables tailored noise reduction for various applications.
-
Product
Service Ground Test Set
900
-
TESCO’s Service Ground Test Set has been designed to check the condition of the ground connection on a secondary service. If for any reason the ground connection has a resistance, this can be immediately detected by the Test Set. The Service Ground Test Set consists of a voltmeter which can be shunted by a resistance of 60 ohms. The voltmeter is of the suppressed zero type with a double range, from 65 to 130 or from 130 to 260, and can be used for checking service voltage independently of the ground test.
-
Product
Frequency Multipliers
-
Excellent suppression of undesired harmonics and spuriousLow multiplier lossRugged coaxial and surface mount packages
-
Product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
-
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
High Voltage 50 Ω Pulse Generator
TLP-8010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Combines TLP-8010A and TLP-4010C into one system*Can be operated together with TLP-8012A5 and TLP-3011C pulse width extenders*Ultra fast 50 Ω high voltage pulse output with typical rise time 100 ps (0-40 A) and 300 ps (> 40 A)*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω configuration*High pulse output current up to ±80 A (short circuit) with minimum 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns (0-40 A), 1 built-in pulse width: 100 ns (> 40 A)*The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0-40 A)*Optional external pulse width extensions from 5 ns to 500 ns (> 40…80 A) using the external pulse width extender TLP-8012A5*Built-in pulse reflection suppression*Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
Product
Power device test system
-
This system is suitable for DC testing of IGBT, IGBT module (1in1～7in1). Built-in hi-current switching relay circuit inside test head, it is capable ofDC testing from device itself to module. Highly accurate repeatability testing is available by high speed rise time which is suppressed its heat in hi-current
-
Product
Emergency Power Supply Units (EPSU) (14) 5-15R 1U/0U V/H
EPS-1415-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Multiphase Power Analyzer
2800 Series
-
The Valhalla Scientific 2800 High-Precision Power Analyzer is available in 1-, 2-, 3-, 4-, 5-, or 6-phase versions. All voltage inputs 0.3V up to 1500V peak and all current inputs 1.5mA up to 1A; 15mA up to 5A; 1A up to 40A; and shunt inputs 60mV up to 6V are potentially free and exhibit low noise, high common mode suppression, excellent DC-stability, wide frequency range (DC-2MHz) and very low self-heating on current inputs.There is no need to fiddle with DC-compensation, or changing current plugging. All is built into the input sections of the power analyzer, ready for measurements. It is simple to use, your intuition will guide you to operate the Power Analyzer touch screen correctly.
-
Product
Frequency Doublers
-
Teledyne Microwave Solutions (TMS) offers several Frequency Doublers providing high fundamental suppression, broadband input/output frequencies, and low conversion loss figures for a variety of communications applications.
-
Product
SonarMite Windows Tablet, Win 7, 8,10 & Mobile Software
-
The SonarMite software presents the user with a three window interface separated by ‘Splitter Window Bars’ which can be dragged to increase or decrease the active window size. If the window is sized to less than a proportion of its width then the window will suppress graphic output and present a scaled text message.
-
Product
Specimen Preparation Equipment
-
Thermal damage can be reduced by cooling the specimen with liquid nitrogen during processing.Designed to suppress the consumption of liquid nitrogen, allowing long cooling periods.Rapid cooling of the specimen while immersed in liquid nitrogen. Return to room temperature. Designed to allow parts to be detached.
-
Product
Compact Photoelectric Sensor
CX-400 Ver.2
-
Panasonic Industrial Devices Sales Company of America
For the CX-400 Series, the user has a large selection of ultra compact Photoelectric Sensors at his disposal. The Series includes three thru-beam, five retro-reflective, four diffuse reflective and four trigonometric types with foreground/background suppression. With its new ASIC (application specific integrated circuit), the Sensors require up to 60% less energy than before.
-
Product
Frequency Multipliers
-
The Kuhne electronic Frequency Multipliers can be characterized by a high band width, a very good suppression of fundamental and harmonic waves, a small current consumption and a very compact housing.
-
Product
Emergency Power Supply Units (EPSU) (24) 5-20R 0U V
EPS-2420-V60
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
-
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
Product
Balanced Optical Receivers
-
For noise sensitive experiments, we offer balanced photoreceivers that suppress up to 50 dB of laser / source intensity noise in experimental set-ups. These balanced optical receivers with two well-matched photodetectors can eliminate the need for lock-in amplifiers and can make all of the difference when you are trying to detect a small signal in applications like absorption spectroscopy, or heterodyne detection.
-
Product
LTE Networks
-
PBE offers secure and reliable wireless solutions for critical mining and tunnel construction operations. Complete end-to-end private LTE networks provide unified infrastructure for underground applications with different QoS, bandwidth and latency requirements.PBE private LTE allows customization of the capabilities of public cellular LTE networks and scale it according to the size and requirements of the particular mine. P-LTE networks provide both human and machine communications on a single, seamless and extendable network that offers long ranges of propagation. In addition to the standard telemetry (air quality monitoring, ventilation management, pump control, belt control, fire suppression, evacuation alerting stations, etc.) LTE networks provide a gateway for:- Voice Communications (VoLTE, VoIP, Push-to-Talk)- Video Communications- CCTV- Internet Access- LAN Access- Real Time Machine Control- Fleet/Asset Management- Access Control/Localization- Automation- Collision Avoidance- Remote Diagnostics
-
Product
Surge Power (Joule Rating 342) (10) 5-15R 1U/0U V/H
EPSS-1015-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
