Modulation Analyzers
Measure and analyze radio transmitters and communication systems.
See Also: Modulation, Optical Modulation, Modulation Analysis, Modulation Meters, MER
-
Product
PXI Vector Component Analyzer, 100 kHz to 32 GHz
M9816AS
Vector Component Analyzer
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
Product
PXI Solid-State Switch Module, 6xSPST, 1.5 A, 400 V, Hardware Interlock
40-185A-001-HI
Switch Module
The 40-185A-001-HI has 6-off high current SPST switches with hardware interlock in two PXI slots and is part of our range of high power solid state switching solutions.
-
Product
PXI 2 Banks of 80 Channel 1 Pole MUX
40-615-022-2/80/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
Controls Systems for Engine Control and Combustion Analysis
NI Powertrain
Analyzer
NI Powertrain Controls systems incorporate the LabVIEW reconfigurable I/O (RIO) architecture to create some of the world’s most flexible and capable combustion analysis and engine control systems. The engine control systems can drive both solenoid and piezoelectric direct injectors, control timing events with 25 ns of precision, and implement novel engine control strategies such as next- and same-cycle control. The combustion analysis systems are available in both portable and higher performance stationary form factors.
-
Product
PXI Very High Density MUX 49 Chan 4 Pole
40-675-002-49/4
Multiplexer Module
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
OSM R1.1 Size-L Module Based On MediaTek Genio 510 Series Processor
OSM-MTK510
Computer on Module
The OSM-MTK510 is an OSM R1.1 Size-L module featuring the advanced MediaTek Genio 510 series processor. Equipped with a dual-core Arm Cortex-A78 and a quad-core Cortex-A55, it boasts an impressive MediaTek DLA+VPU AI engine capable of up to 3.2 TOPS, making it ideal for edge AI applications. This module excels in providing edge AI processing at ultra-low power consumption.
-
Product
PMC Module
PMC-CycloneII-64LVTTL
PMC Module
User Programmable Altera Cyclone II FPGA 672 BGA, EP2C35, EP2C50, EP2C70, Stand alone possibility, Single wide PMC Module, 64 LVTL, Optional User clock oscillator
-
Product
PXI Single 16 Channel Switch Simulator
40-485-221
Switch Module
Designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 26.5GHz, 50Ω, SMA, Remote Mount
40-785C-532-E
Multiplexer Module
The 40-785C-532-E (PXI) and 42-785C-532-E (PXIe) are dual SP6T 26.5GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Solid State Switch Module, 3xSPST, 10 A, Hardware Interlock
40-182A-012-HI
Switch Module
The 40-182A-012-HI has 3 off high current SPST switches with hardware interlock in one PXI slot and is part of our range of high power solid state switching solutions.
-
Product
PXI/PXIe Microwave Transfer Switch, Dual, 18 GHz, 50 Ω, SMA, Failsafe
42-782B-522
Switch Module
The 40-782B-522 (PXI) and 42-782B-522 (PXIe) dual failsafe transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 9-Bank 6GHz SMA
60-802-009
Multiplexer Module
The 60-802-009 is a 4-channel, 9-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI Multiplexer, Single 64-Channel, 1-Pole
40-630A-022-64/1
Multiplexer Module
The 40-630A-022-64/1 is a single 64-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
NI-9201 , ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
779013-01
Module
±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. The module features up to 100 V of overvoltage protection for errant signal connection or unexpected signals to the individual channels.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 67 GHz, 50 Ω, SMA-1.85, Failsafe
42-785C-571
Multiplexer Module
The 40-785C-571 (PXI) and 42-785C-571 (PXIe) are single failsafe SP6T 67 GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Fault Insertion Unit
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 3GHz, 50Ω, N-Type, Terminated, Remote Mount
40-785C-562-TE
Multiplexer Module
The 40-785C-562-TE (PXI) and 42-785C-562-TE (PXIe) are dual SP6T 3GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI 2 Amp Multiplexer, 38-Channel, 2-Pole
40-656A-001
Multiplexer Module
The 40-656A-001 is a 38-channel multiplexer with 2-pole switching, suitable for signals to 2 Amp, 220VDC/125VAC. It offers the highest switching density in its class for medium power/voltage signals.
-
Product
PXI-2555, 2.5 GHz, 75 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module
778572-55
Multiplexer Module
2.5 GHz, 75 Ω, Terminated 4x1 PXI RF Multiplexer Switch Module—The PXI‑2555 is an RF signal multiplexer switch module. The internal termination of the PXI‑2555, which helps prevent high-power reflections that arise from open channels on the module, makes it ideal for use in video RF applications where such reflections can damage the source. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
Product
PXI Microwave Multiplexer, Single SP8T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
40-788-041-E
Multiplexer Module
The 40-788-041-E (PXI) and 42-788-041-E (PXIe) are single failsafe SP8T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
Power, Module, Receiver, CASS, 76 Position
510114107
Receiver Module
Module, ID, Cass, Signal, 76 Positions, Discrete Wiring
-
Product
Switch PXI Solid-State Switch Module, 6xSPST, 25 A, 100 V
40-184A-001
Switch Module
The 40-184A-001 has 6-off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, MU Connectors, With Interlock
42-850A-314-HI
Multiplexer Module
The 40/42-850A-314-HI is a PXI/PXIe 4-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 67 GHz, 50 Ω, SMA-1.85, Terminated, Remote Mount, Failsafe
42-785C-472-TE
Multiplexer Module
The 40-785C-472-TE (PXI) and 42-785C-472-TE (PXIe) are dual failsafe SP4T 67 GHz with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-318-M50
Multiplexer Module
The 40/42-852A-318-M50 is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 40GHz, 50Ω, SMA-2.9
40-785C-443-TE
Multiplexer Module
The 40-785C-443-TE (PXI) and 42-785C-443-TE (PXIe) are triple SP4T 40GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe RF Multiplexer, Single 8-Channel, Terminated, 8GHz, 50Ω, SMA
40-883B-001
Multiplexer Module
The 40-883B-001 (PXI) and 42-883B-001 (PXIe) are single 8 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. It is available in 8 to 1 and 16 to 1 configurations in two and three slots respectively.
-
Product
PXIe-7971, K325T FPGA, 1.7 GB/s PXI FPGA Module for FlexRIO
782953-01
FPGA Module
K325T FPGA, 1.7 GB/s PXI FPGA Module for FlexRIO—The PXIe‑7971 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXIe‑7971 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software. The PXIe‑7971 supports peer‑to‑peer streaming, which directly transfers data among multiple FPGA modules or select PXI Express modules without sending data to the host processor. With this feature, you can add FPGA capabilities to high-performance NI digitizers with NIST‑traceable calibration or expand your FPGA algorithms across multiple FPGAs for computationally demanding applications.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, SC/PC Connectors
42-852A-218
Multiplexer Module
The 40/42-852A-218 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-784B-131-E
Multiplexer Module
The 40-784B-131-E (PXI) and 42-784B-131-E (PXIe) are single failsafe SP4T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
