GHz Synthesizers
See Also: GHz
-
product
DC - 12 GHz Packaged High Efficiency Divide by 8 Prescaler
HMMC-3128-TR1
The HMMC-3128-TR1 is a packaged DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
Coax, Contact, Receiver, 20/26 GHz, Flex 402
610102119
Coax contact, Receiver, 20/26 GHz, Flex 402 (Only available in patchcords).Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield-SolderInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.25 for 2 - 18 GHz1.30 for 18 - 26 GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications Flex 402 (Only Available in Patchcords)Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition AInsulation Resistance 2000 MΩ Min.
-
product
PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, Failsafe
42-780B-532
The 40-780B-532 (PXI) and 42-780B-532 (PXIe) are dual failsafe SPDT 26.5 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
Oscilloscope, 1 GHz Bandwidth, 4 Input Channels, 50 Mpts/ch, 10 GS/s
HDO6104B
1 GHz, 4 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch High Definition Oscilloscope with 15.6" Display.
-
product
4-in-1 OSLT Mechanical Calibration Kit, DC To 40 GHz, 2.92 Mm (f)
85561A
Combines an open, short, load, and through standard in a compact unit that is easy to handle and lightweight.
-
product
Nonlinear Component Characterization 10 MHz - 110 GHz
S94510B
Measure and display the calibrated, vector corrected waveform of the incident, reflected, and transmitted waves of the DUT
-
product
SP1T RF Pin Diode Switches To 18 GHz
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
product
4-In-1 OSLT Mechanical Calibration Kit, DC To 18 GHz, Type-N (f) 50 Ohm
85519A
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
product
PXIe Vector Network Analyzer, 10 MHz To 20 GHz
M9834A
The M9834A PXI network analyzer (VNA) offers unrivaled performance for testing multiport, multisite, multi-DUT modulated signal measurement from 10 MHz to 20 GHz.
-
product
2X8 PXIe Switch Matrix, 300 KHz to 6.5 GHz
M9165A
M9165A 2X8 PXIe switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provide a switch based multiport VNA solution.
-
product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 40 GHz, 50 Ω, SMA-2.9, Remote Mount, Failsafe
42-785C-443-E
The 40-785C-443-E (PXI) and 42-785C-443-E (PXIe) are triple failsafe SP4T 40 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
CW IMPATT DIODES FROM 30 TO 140 GHz
Insight Product Company offers IMPATT diodes with CW power up to 400 mW and operational frequency range up to 140 GHz. Silicon p+-p-n-n+ IMPATT diodes are designed to be used in the millimeter wave oscillators and amplifiers. They are fabricated in the metal-ruby packages with hard-lead carrier (diameter 3.0 mm, 1.5 mm).
-
product
PXIe-8861, 2.8 GHz Quad-Core PXI Controller
785831-01
PXIe, 2.8 GHz Quad-Core PXI Controller - The PXIe‑8861 is an Intel Xeon 4‑Core embedded controller for PXI Express systems. You use it for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8861 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt™ 3 ports, and other peripheral I/O. Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
PXI/PXIe Microwave Relay, Single SPDT, 12.4 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-780B-511-E
The 40-780B-511-E (PXI) and 42-780B-511-E (PXIe) are single failsafe SPDT 12.4 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT front panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-785C-532-E
The 40-785C-532-E (PXI) and 42-785C-532-E (PXIe) are dual failsafe SP6T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
10 MHz To 67 GHz USB Wide Dynamic Range Peak And Average Power Sensor
U2067XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
4-in-1 OSLT Mechanical Calibration Kit, DC To 18 GHz, Type-N (m) 50 Ohm
85518A
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
product
PXI Programmable Step Attenuator Module, DC to 50 GHz
M9168E
The M9168E is a programmable step attenuator module based on PXI hybrid platform. The M9168E operates from DC to 50 GHz with a guaranteed 0.03 dB insertion loss repeatability for each section throughout the 5 million cycles operating life. Superior attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 40 GHz, 50 Ω, SMA-2.9, Failsafe
42-785C-442
The 40-785C-442 (PXI) and 42-785C-442 (PXIe) are dual failsafe SP4T 40 GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
PXI Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, Failsafe
40-780B-531
The 40-780B-531 (PXI) and 42-780B-531 (PXIe) are single failsafe SPDT 26.5 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
product
Basic Pulsed-RF Measurements For VNA Up To 53 GHz
S970251B
Add pulsed-RF measurement capabilities to your P50xxB Streamline series vector network analyzer
-
product
Active Device Characterization Solution Up To 67 GHz
N5247BM
The N5247BM provides the N5247B 67 GHz PNA-X network analyzer, application software and accessories for active device characterization up to 67 GHz.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP12T, 8 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
40-788-212-E
The 40-788-212-E (PXI) and 42-788-212-E (PXIe) are dual failsafe SP12T 8 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
product
Precision Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052C
The Keysight 85052C precision mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection.
-
product
10 MHz to 50/53 GHz USB Wide Dynamic Range Average Power Sensor
U2055XA
The Keysight U2055XA is a fast, accurate and wide dynamic range 10 MHz – 50/53 GHz USB average power sensor.
-
product
20/26 GHz/ 75 Ohm HD/ Coax, Module, ITA, iCon Series, 18 Position
510161114
Primary mating module 510160114. (May mate with other Receiver modules, as well.)
-
product
RF Test Enclosure With Preconfigured I/O Panels, ≥ 90 dB Isolation, 300 MHz - 18 GHz
dbSAFE X
The dbSAFEx Series advanced shielded boxes are versatile for any wireless testing. Designed to operate between 300 MHz to 18 GHz, testing of wireless devices has never been more reliable and affordable.
-
product
Waveguide Harmonic Mixers (smart mixer), 50 to 75/80 GHz
M1970V
The Keysight M1970V 50 to 75/80 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of the N9030A PXA, N9020A MXA, and N9010A EXAsignal analyzers up to 80 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
product
PXIe8862, 2.6 GHz 8-Core PXI Controller
789546-01
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
