PMC Adapters
Computer boards that translate the data from the PMC bus to another bus and vice versa. They are used to connect two incompatible buses. (globalspec.com)
-
Product
Flexible MiniPCI Express to PCI Adapter
SKU-034-0X
-
Flexible MiniPCI Express to PCI Bus Adapter (Adapter) was designed to convert the MiniPCI Express bus into two 32-bit PCI buses. It allows to connect up to 2 32-bit PCI expansion boards to the motherboard MiniPCI Express connector (supports full-size and half-size MiniPCI Express host boards).Adapter includes a PCI adapter, MiniPCI Express host board (full-size or half-size) and PCI Express flat Cable.
-
Product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
Network Interface Controller
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Male Adapter, .025" Round Post (Adapter Pin)
610138117
Signal Contact (Receiver)
Primary mating contact 610138100. (May mate with other Twin Female contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
Product
Thermocouple (J-Type) And Temperature Probe Adapter
U1185A
-
The U1185A consists of a thermocouple bead (J-type) and a mini connector to dual banana plugs.
-
Product
Adapter, 2.4 mm (m) to 3.5 mm (f), DC to 26.5 GHz
11901C
-
The Keysight 11901C is a metrology grade, 2.4 mm male to 3.5 mm female adapter with dc to 26.5 GHz operation.
-
Product
Run Down Adapters
RDA
-
The run down adapter (RDA) is designed to provide consistent and reliable torque readings for use with power driven torque control tools. The RDA’s reduce the impact and irregular peaks that cause poor repeatability. Each RDA has an effective torque range and will supply repeatable torque data within that range if used correctly. The run down adapter is mounted in-line between the tool drive and transducer.
-
-
Product
DH Series QuickLink Adapter Kit with 3 x QL-SI Tips
DH-QL-3SI
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
XA GPIB Cable Adapter
181638-01
GPIB Cable
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Male or Female GPIB (IEEE 488) Adapter - The GPIB Adapter connects GPIB cables to other accessories. NI offers it in Type XA, XE, and XF.
-
Product
M.2, MiniPCI Express, USB, RS232, TTL Adapters
-
Amfeltec M.2, MiniPCI Express, USB, RS232, TTL Adapters
-
Product
USB to VGA Adapter with Retention, USB Type-C Male to VGA Female, 0.5m
143557-0R5
USB Connector
24-Pin USB-C 3.1 Male to 15-Pin VGA Female, 0.5 m Display Cable - The VGA15F-USB24M Cable for CompactDAQ and CompactRIO controllers and chassis features a male USB-C connector and a female VGA connector.
-
Product
Basic CMC Extender for PrPMC, PMC, and PMC-X
4320
-
Basic CMC Extender for PrPMC, PMC, and PMC-X. The Basic Common Mezzanine Card (CMC) extender provides a means to extend IEEE 1386 boards for signal accessibility. PrPMC (VITA 32), PMC (IEEE 1386.1), PMC-X (VITA 39) and any other CMC-derived board is supported.
-
Product
Connector Adapter
-
MCA-ST connector adapter for the connection of micro plugThe connector adapter allows the direct connection of fine-pole connectors on circuit carriers or jumpers. The adapter is guided over the connector housing, which overcomes the tolerances of carrier and mounting.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2x68 Male SCSI Connectors
510150125
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Male SCSI Connectors
-
-
-
Product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 57624
-
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
High Resistance Measurement Universal Adapter
N1414A
-
N1414A High Resistance Measurement Universal Adapter is used to simplify the connection for high resistance measurements by B2980A series electrometer.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
-
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
PMC Products
-
Our PMC modules are based on technology and circuit designs with time-tested reliability in thousands of installations. Great effort goes into selecting high-performance parts to withstand the demands of military, aerospace, and manufacturing applications. Most models are available with extended temperature ranges for reliable operation in harsh environments. Acromag products are also designed for the long lifecycles required for OEM and defense projects.
-
Product
AC Current Clamp Adapter
LAD-1100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Selectable measuring range 30mA~30A with CT ratio 10:1 and 30A~3000A with CT ratio 100:1.●φ110mm CT window, possible to measure from leakage to big current up to 3000A.
-
Product
ProLink to 2.92mm ProAxial Adapter with Probe Power and Communication Pass Through
LPA-2.92-PX-KIT
-
ProLink to 2.92mm ProAxial Adapter with Probe Power and Communication Pass Through.
-
Product
RF Adapters
BNC Adapters
-
Amphenol RF offers a wide array of both in-series and between-series BNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance BNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm BNC connectors have a frequency range from DC to 4 GHz. 75-ohm BNC connectors optimized for 4K/UHD video applications can perform well to 12 GHz.
-
Product
PMCspan PMC Expansion Board
PMCspan
-
SMART Embedded Computing’s PMCspan allows users to customize and expand I/O options when coupled with a Smart SBC.
-
Product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (f) To WR-12, 60 To 90 GHz
E281CS
-
E281CS E281CS In-line 1.0 mm (f) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
Product
Adapter, 1.0 mm (m) to 1.85 mm (m), DC to 67 GHz
11921E
-
The Keysight 11921E precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
Product
32/64b 33/66 MHz PCI-x to PMC-x Adapter
8098a
-
The PCI-X to PMC-X Adapter permits operation of a standard 32 or 64 bit PCI-X card in a PMC-X slot while providing a migration path for PCI-X board suppliers to port their products to a PMC-X form factor.
-
Product
Swivel Tip Adapter for ZD Differential Probe Qty 1
PACC-ZD005
-
Swivel tip adapter for ZD differential probeQty 1
-
Product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male SCSI
510109470
Pull-Thru Adapter
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male SCSI
-
Product
Adapter, 1.0 mm (m) to 2.4 mm (m), DC to 50 GHz
11922A
-
The Keysight 11922A precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
