Circuit
-
Product
Battery Backup IC
-
Analog Devices offers a range of supervisory circuits that offer a complete single chip solution for power supply monitoring and battery control functions in microprocessor systems. Functions include microprocessor reset, backup battery switchover, watchdog timers, CMOS RAM write protection, and power failure warning.
-
Product
Silver Plated Test Points
-
The fabricators of SMT printed circuit boards may take advantage of the convenience of field testing with the unique loop design of Components Corporation's TP-107 and TP-108 series of surface mounted, printed circuit test points is now available in silver-plate for outstanding reliability. All products are RoHS and REACH compliant.
-
Product
Circuit Tester
TE6-0720
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*For use on cars, trucks, boats, trailers and motorcycles*Needle point probes *Use to trouble shoot both primary and secondary circuits*Use this tester to check primary circuits of 6/12V*On secondary or high voltage circuits you can check spark plugs
-
Product
Electrical Circuits Control Device
ZET 452
-
ZET 452 is an automated module for electrical circuits parameters control that is used for electrical circuits impedance and insulation resistance monitoring in automated mode. The monitoring is performed in accordance with the set participation and without participation of an operator. ZET 452 allows to reduce the time necessary for verification procedure more than in 20 times if compared with the standard measurement instruments normally used for these purposes.
-
Product
Clamping Voltage Tester
MIG0603CLV2
-
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
Product
Telephone Line, PCM and Other Copper Wire Tester
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber Tel Line, PCM and Other Copper Wire Tester is developed for the fault testing of local telephone circuit using internationally advanced measuring technique in connection with the current situation of domestic telephone network. The instrument is of portable structure, and specially designed for the use of telecom and exchanger room operating staffs, line attendants, mobile phone servicing staffs and etc.
-
Product
1000 Amp AC/DC Inductive Amp Clamp
6043
-
• A great tool for accurate measurement of current sources up to 1000 amps• Use with most digital multi-meters• 1mV/Amp output guarantees easy reading on your meter• Ideal for checking starter draw, alternator output or parasitic battery drain testing• Design allows accurate current readings without breaking the circuit• Low battery indication – auto power-off• Switch settings OFF/200A/1000A• Large jaw opening, 2.2″ and large jaw space, 2.2″ x 2.75″• Imported
-
Product
Analog Isolator
-
The Analog Optical Isolator module is a single isolated current in / current out or voltage in / voltage out channel of physical separation and electrical isolation for establishing and maintaining the independence of Class 1E equipment from non -Class 1E instrumentation circuits. Input-to-Output isolation has a steady-state isolation capability of 2500 volts AC rms. This isolation will be maintained between:a) input to output signalsb) input to output powerc) output signal to input power
-
Product
Mass Flow Controllers for Gases
-
Sensirion''s mass flow controllers are characterized by fast and accurate control of gas flow over a wide dynamic range. Based on the innovative CMOSens Technology, the heart of these mass flow controllers is a calorimetric microsensor (MEMS), which is integrated with the complete signal conditioning electronics on one single chip. While the flow is measured using the thermal measurement principle, efficient control is provided by an analog controlling circuit. This unique integrated technological approach results in excellent performance and reliability - at a very attractive cost.
-
Product
Multibus Extender
3690-18
-
VECTOR Electronics and Technology, Inc.
Length : 7.65"(190.5 mm)Height : 12.0"(304.8 mm)Contacts : 30 Contacts each side on 0.100" centers 43 Contacts each side on 0.156" centersConnector : Gold plated, mounted on top and connected to circuit tracesCurrent Rating : 5 amps at 10°F rise
-
Product
SIMRC - 16-Channel 2-Pole Multiplexer
1020-R-16-2-5/1D
Multiplexer Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
High Impedance Active Probes
7
-
Designed as a companion probe to Models 12C and 18C for driving integrated circuit lines so the Model 12C and 18C can be used to measure the response of adjacent nodes. The Model 7 consists of a flexible 6 foot, 50 ohm coaxial cable accurately terminated to 50 ohms in order to avoid undesirable reflections. A special miniature connector receives replacement coaxial probe tips that provide a shielded environment to within 3 mm of the fine tungsten probe point, thus minimizing capacitive coupling to other parts of the circuit. The replaceable coaxial probe tips are offered in various point sizes and can also be bent to any shape in order to accommodate a variety of probing geometries.
-
Product
Compact Photoelectric Sensor
CX-400 Ver.2
-
Panasonic Industrial Devices Sales Company of America
For the CX-400 Series, the user has a large selection of ultra compact Photoelectric Sensors at his disposal. The Series includes three thru-beam, five retro-reflective, four diffuse reflective and four trigonometric types with foreground/background suppression. With its new ASIC (application specific integrated circuit), the Sensors require up to 60% less energy than before.
-
Product
Wrist Strap and Foot Wear Testers
-
Connects to utility ground when plugged inQuick, easy installation and grounding of both wrist straps and table mats.Tests entire circuit - wrist strap, cord and skin contactReliable resistance testActs as common point ground for the worksurface
-
Product
Solid-State And Electromechanical Relay Products
-
Relay is the name for a switch that is operated electro-mechanically or electronically. Their main task is to make and break connections to control the flow of current in electrical circuits. They’re used for various purposes ranging from validating semiconductors to interfacing low power computers or microcontrollers with high power machinery.
-
Product
Digital Control VGAs
-
Analog Devices digital controlled variable gain amplifiers provide discrete levels of gain control over a fixed number of control bits for a variety of audio and optical frequency bands. Our VGAs improve the dynamic range of a circuit by allowing users to adjust the amplitude of a signal in real time, which is critical for a number of applications involving ultrasound, speech analysis, radar, wireless communications, and instrumentation. We also offer a portfolio of voltage controlled VGAs to provide you with continuous gain control over a wide dynamic range.
-
Product
RF-Ready DC Fixture
-
The RF-Ready DC fixture provides space for mounting RF input and output matching circuits. Hence, it is possible to tune up the assembly at a remote test station, such as a network analyzer, to peak performance and then run the life test with DC stimulus. The matching structures also allow incorporation of more complex stabilization structures.
-
Product
Capacitor Tester
MIG0603CAP
-
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
Product
voltage controlled crystal oscillator
VCXO
-
A VCXO (Voltage Controlled Crystal Oscillator) is a crystal oscillator the output frequency of which is controlled by adding an external control voltage via a frequency control input on a variable capacitance component such as a varactor diode connected in parallel to a load capacitance (CL). Epson VCXOs are divided into two types according to Voltage-Frequency (V-F) characteristic slopes depending on the AFC (Automatic Frequency Control) input configuration of the VCXO. One is a VCXO with a positive V-F slope and the other is a VCXO with a negative V-F slope. Please note that the input voltage of a control circuit will vary according to the individual type, as shown in Figs. 3 and 4. Epson's VCXOs are capable of either, depending on the customer's preference. Epson's VCXOs have been increasingly used for broader applications such as slave oscillators in phased-lock loops, or frequency modulators. Among the above types, a VCXO combined with a TCXO is called a VC-TCXO , respectively. These components have the merit of delicately controlling their output frequency electrically.
-
Product
PCI Express
-
PCI Express (PCIe) is a highly successful SerDes interface that is used in computing devices spanning a wide range of applications. Currently in its fourth generation with on-going roadmap development for a fifth generation, the PCIe interface is undergoing major technical advancements that require state-of-the-art development and validation tools. For example, Gen4 PCIe devices operate at 16 Gbps per lane and are expected to deliver very low bit error rate (BER) levels even over constrained and lossy transmission channels (e.g. printed circuit boards).
-
Product
IGBT For IH
-
IGBT devices for induction heating (IH) (soft switching), recommended for 10 to 100 kHz frequencies, and not guaranteed against short circuit.
-
Product
Test Fixturing Solutions
-
Amfax and MAC Panel have teamed up to provide a unique WIRE-FREE Test fixture technology. We have created an alternative solution to traditional wired ITAs called PECture(TM). The name is a combination of PEC (Printed Electronic Circuit) and fixture.
-
Product
Transient Immunity Tester
KES7700
-
Transient Immunity Tester KES7700 Series are transient surge tester that utilizes a compact unit system. A surge generator circuit is installed for each pulse unit as the tester meets the requirement of ISO7637-2, ISO7637-3, ISO16750-2, JASO D001, SAEJ1113, and other standards. The KES7700 Series meets a broad range of independent automobile manufacturer standards as well.
-
Product
LXI Low Thermal EMF Matrix 1-pole 56x33
60-510-001
Matrix Switch Module
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
Product
PXI RTD Simulator Module, 16 Channel, PT100
40-263-201
Simulator
The 40-263-201 is a 16-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
6 Round Pin Trailer Circuit Tester
PT7897
-
Tests trailer circuits on most light/medium duty trucks and campers.Traces each lighting function to the terminal in question.
-
Product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2320
-
CableTroll 2320 is an indicator for detection of Earth faults (PtG) and short circuit (PtP) faults on multi-core and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Resister
-
Our ARFC type Film Flat Chip Resistor & ARFCN type Thin Film Chip Resistor Network are high precision Metal Film resistors produced with high purity. Alumina Substrate and Ni-Cr-Si Resistor Film based on high precision Etching Technology. The electrode Terminals are made with Spattering Film and Nickel-Solder Plating, and solderability is very good in all Flow, Reflow and Dipping type soldering for Hybrid IC, SMT, PCB etc. Our ARFC Metal Film Resistor & ARFCN type Thin Film Chip Resistor are being produced under the thorough quality control, and are being used widely in high precision and high reliability electronics circuit such as Measuring Instrument, Medical Instruments, Communication and other Industrial Instruments.
-
Product
2-18GHz Instantaneous Frequency Measurement Unit
DR073
-
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
Product
Copper Pillar Bump
-
Like in conventional fabrication, integrated circuits are created on the wafer but near the end of the manufacturing process, the attachment pads are metalized on the surface of the chips to make them more receptive to solder. Then solder dots are deposited on each of the pads, and chips are cut, flipped, and positioned so that the solder balls are facing the connectors on the external circuitry.
