AC DC Clamp Meters
measure AC-DC amperage without contacting conductors.
See Also: AC/DC Current Probes
-
Product
3-Phase AC Power Source
61700 series
-
The Chroma Programmable AC Power Source model 61700 series delivers pure, 5-wire, 3-phase AC power. Unlike the traditional 3-phase AC power source, it includes low power rating models at very low cost. Users can program voltage and frequency, measure the critical characteristics of the output on its LCD display. It delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA. It is also suitable for commercial applications from laboratory testing to mass productions. The 61700 supplies the output voltage from 0 to 300VAC and it can be set individually for each phase. Users also can set the phase angle from 0? to 360?. These kinds of function make the 61700 series can simulate unbalance 3-phase power. Because of the wide output frequency from 15 to 1200Hz, it is suitable for avionics, marine and military application. The AC+DC mode extends the output function to simulate abnormal situation when power line contains DC offset.
-
Product
Industrial AC Drives
-
Our drives cover every automation application need in the industrial plant. These AC drives incorporate the latest technological advancements in AC motor speed control, made possible by experience and dedication to quality in design and manufacturing.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-33
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 0.1A～150A*Current measurements of feeder
-
Product
DC Electronic Load
Model - KM-mPD-501
-
Kusam Electrical Industries Limited
KM-mPD-501 DC electronic load mainly focuses on the testing of power circuit on PCB. KM-mPD-501 offers a solution for function test of Switch step up, Stepdown, Regulators and Driver IC . Engineer puts components, such as CPU, DSP, FPGA; etc on a PCB after the power circuit has been tested. It’s not complete to use a meter to measure the voltage. KM-mPD-501 offers engineer OVP, OCP and OPP functions that help engineer know the value of overload current . On the other hand, engineer can use a programmable DC power supply (mPP series) to offer external power and connect PCB’s output to KM-mPD-501. Then engineer can easily get output watt, figure out the efficiency of power circuit and check if inductances, capacitances and resistances perfectly work with the power circuit. KM-mPD-501 not only offers loading emulation of current but also provides OVP and OPP. User can use these functions to test solar power battery, rechargeable battery and motor driver. In school laboratory, KM-mPD-501 helps students do experiment on power circuit, linear circuit and driver circuit.
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-340L
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
AC Switches
-
Our ACST series are over-voltage protected triacs that protect themselves by folding back and leading current into the load when subjected to an overvoltage.
-
Product
AC Power Measurement and Logging
WattNode® Logger for LonWorks®
-
Continental Control Systems LLC
The WattNode Logger is a kilowatt hour (kWh) energy meter that communicates on a LonWorks network, and can log 24,000+ measurement records in non-volatile memory. The WattNode Logger measures 1, 2, or 3 phases with voltages from 120 to 600 volts alternating current (Vac) and 5 to 6,000 amps in delta (phase to phase) and wye (phase to neutral) configurations.
-
Product
DC to DC Power Converters
-
CEHCO can supply DC to DC Power Converters. We offer customized solutions. The DC to DC Power Converters are from 1 KW to 200 KW.We need additional information from the customer as shown below:DC input voltage rangeDC output voltage rangeMaximum output current requirement and rangeOther requirements (ex: response time, ripple, remote control… etc)
-
-
Product
DC POWER
VARIABLE TRANSFORMER
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
Product
DC Energy Meter
-
Multiple channels can be measured by a single meter, EN2450N & EN2450D. Differential current input for all the current channels. Programmable shunt secondary 50mV to 100mV. Programmable CT Primary for all channels up to 200A - for Hall Effect CT. Data logging for parameters such as Energy, Load hours and Ampere hours. Easy installation,Compact size, weight and simple wiring.
-
Product
3-Phase Programmable AC Source
61700
-
Chroma Systems Solutions, Inc.
Power: 1500VA, 3 (61701); 3000VA, 3 (61702); 4500VA, 3 (61703); 6000VA, 3 (61704); 12000VA, 3 (61705)Voltage: 0~150V/0~300VFrequency: 15~1.2KHzPhase angle: 0~360Built-in PFC, provides input power factor over 0.98Advanced PWM technology delivers high power density in a compact rack-mountable packageBuilt-in output isolation relaysAC+DC output modeProgrammable slew rate setting for changing voltage (optional function)Turn on, turn off phase angle controlUser-definable power-on statusPower line disturbance (PLD) simulation capability (optional function)Comprehensive measurement capability: V, Irms, Ipk, I inrush, P, PF, CF of current etc.Programmable r.m.s. current limitFull protection: OP, OC, OV and OT protectionGPIB and RS-232C interface (optional)Easy-use software for operation
-
Product
AC Hipot Test Set
-
Weshine Electric Manufacturing Co., Ltd
AC Hipot Test Equipment for Dielectric Withstand Test are suitable for 50 / 60 Hz AC testing of low capacity test objects. Optionally, these units can also be upgraded to function as DC test sets by mounting the rectifier attachment on top of the transformer.Weshine® AC Hipot Test Set for AC hipot test can be equipped with a rectifier attachment for DC voltage testing.Typical application areas:Testing of cables Testing of switchgearTesting of transformersTesting of CP & PTTesting of MV systems
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-18S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Ultra compact size with 18mmφ jaw opening capability.*High sensitivity and least affection from external magnetic field.
-
Product
High Insulation Digital Clamp Tester
HCL-3000+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・AC current measurements for 20mA～200A.・Easy operation, Push to Open and Pull to Disconnect Mechanism.・Safe AC current measurements for high voltage circuit (AC80 to 7000V).
-
Product
Combinated Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Measure small direct and alternating currents up to 2 A with 1 mA resolution. The device measures the current indirectly via the surrounding magnetic field, so it is measured without contact when the clamp jaws enclose the current-carrying conductor (single wire).
-
Product
AC/DC CAT IV 600 A TRMS Navigator Clamp Meter
ACDC-52NAV
-
The ACDC-52NAV clamp-on power meter is the ideal choice for jobs that require AC/DC current measurements to 600 A, AC/DC voltage to 1000 V and wide jaws to accommodate large conductors.
-
Product
DC Power Supplies
-
High performance and high reliability, is variable DC regulated power supply used in all fields, from research and development and quality control to manufacturing plants.
-
Product
AC Resonance Test System
-
Shanghai Guantu Technology Co., Ltd.
AC withstand voltage test is an effective and direct method to identify the insulation strength of electrical equipment. During the operation of power equipment, the insulation will gradually deteriorate under the action of electric field, temperature and mechanical vibration for a long time, including overall deterioration and partial deterioration, forming problems. question.
-
Product
AC Contactors
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s line up of AC Contactors includes the HE-N, HE PV, and HE-S Series. Differentiating features and benefits of Panasonic AC Contactors include:*High-Voltage, High-Current Control*Compact Size*High Contact Reliability*Can Be Mounted In Any Direction*RoHS Compliant*UL/C-UL Standard Certified
-
Product
Basic Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. This method also enables measurements of very high currents, which would overload any standard multimeter if connected directly.
-
Product
AC Power Supply
-
AC Power Supply, Shuangyi AC power products are mainly linear AC power sources: TFC-1000 series
-
Product
Clamp Earth Resistance Testers
-
Is used for earth resistance test. This meter uses an EBTN screen with a dual display function (the resistance & current displayed). It also has functions such as a real-time clock, data storage, data review, alarm, and automatic shutdown.
-
Product
DC Power Supply
PW-3032
-
*Low Ripple & Noise*30V/3A+5V/3A Dual output.*<0.4m Vrms Ripple & Noise(C.V.)*<2.5m Arms Ripple & Noise(C.C.)*Dual Display.
-
Product
Programmable AC Power Source
LSX Series
-
The LSX Series consists of a range of fully featured, single and three phase AC Power Sources. Available models range from 1.5kVA to 6kVA with an advanced programmable controller sporting a color touch screen user interface. Cost effective and fully programmable for both basic frequency conversion as well as advanced AC power line disturbance test and ATE applications. For applications not requiring advanced features, a basic function set M version of the LSX is available as well.Note: The LMX Series is not CE marked yet at this time.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-40
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～600A*Current measurements of feeder
-
Product
AC DC Current and Voltage Converters
-
The DAT5023 I is an AC or DC current converter, the input current range is selectable on order from 0-5Amps, 0-10Amps, 0-20Amps, 0-25Amps, 0-30Amps, 0-40Amps, 0-50Amps, 0-60Amps. It measure the current with the use of a Hall effect transducer. There is a coil (current transformer) inside the current converter which is isolated from the current input. The cable passes through the housing of the converter and the coil and the true root mean square measurement is taken from this coil then converted to a standard industrial signal output.
-
Product
DC-Powered, AC Voltage Monitor
VAD/VQD
Voltage Monitor
NAI’s VAD and VQD are DC-Powered, AC Voltage Monitors used to monitor voltage characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within pre-determined limits. These voltage monitors are ideally suited for rugged defense and industrial applications.
-
Product
1000A Power Quality Clamp Meter with Temperature
ACD-41PQ
-
The Amprobe ACD-41PQ provides a simple and effective way to verify if the electrical system is affected by harmonics. Add on troubleshooting capabilities with the ACD-40PQ data-logging feature or get complete power analysis with the ACD-41PQ. Increase measuring efficiency with an optional PC interface kit.
-
Product
DC Source/sink
-
Single channel system. One output with up to 1500 V or 1200 A. Maximum power in single operation 650 kW, up to 2.6 MW in parallel operation.
