Shielding Effectiveness
the ability to block an electromagnetic field.
See Also: Shielding, RF Enclosures
-
Product
Shielding Effectiveness
-
Radiometrics Midwest Corporation
One of the more difficult tests to understand is shielding effectiveness or transfer impedance. The data from these tests may vary dramatically based on the test method selected, test fixture, test setup, measurement sensitivity, test personnel, etc. At Radiometrics all shielding effectiveness test are performed or supervised by NARTE Certified engineers.
-
Product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
-
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials.
-
Product
EMI Shielding Effectiveness Testing
-
Eurofins E&E North America can easily develop sound engineering measurement techniques to quantify the SE of your product. Our process involves creating detailed SE Test Plans used to insure accurate and repeatable test results.Eurofins a has years of experience to assure our customers that the evaluation reflects the electrical attenuation performance of the material. Often times, our test report becomes supporting documentation for our customer’s end-user contractual requirement, where Independent Test Laboratory results verify the electrical performance of the material being tested.
-
Product
Antennas
-
The PLA-R and PLA-T are active, battery powered receive and transmit loop antennas for the frequency range 9 kHz - 30 MHz intended for radiated emission testing (PLA-R) and site validation: Normalized site Attenuation, Shielding Effectiveness (PLA-SET consisting of PLA-R and PLA-T)
-
Product
Testing And Design Services
-
Rhein Tech Laboratories, Inc. (RTL) is a full-service design and compliance engineering test laboratory. We have grown with the industry from general purpose EMC testing into other areas of testing such as Radio (RF testing), Military and Aviation, Industrial, Scientific and Medical, Automotive, Electrical Safety, Shielding Effectiveness, Site Surveys and Radar Cross Section & High Range Resolution measurements.
-
Product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
-
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
Product
RF Shielded Enclosure, 100dB from 1MHz to 10GHz
QuietBox-100m
-
The Raymond RF QuietBox-100m line portable shielded enclosures are made from the same proven modular RF shielding materials as full size Modular RF Shielded Enclosure systems and offer the same exceptional RF Shielding Effectiveness. The QuietBox-100m is the perfect portable tabletop and laboratory enclosure where larger interior volume or higher RF Shielding Effectiveness is required.
-
Product
Corona Effect Camera
CoroCAM 8 UAV
-
*High-sensitivity UV detector, which can detect UVc light at 2.05×10-18 Watt/cm2, this allows detection of the smallest corona discharges.*9Hz (or 25Hz optional) IR radiometric camera module*Control of a limited number of camera functions from a standard RC controller using PWM or SBUS.*Remote control of all camera functions from the laptop via an Ethernet link.*Soft sync or staggered zoom of the 3 channel cameras. The IR and UV channels are digitally zoomed in, which is visible...optically zoomed in to the minimum FOV, and then digitally zoomed out.
-
-
-
Product
Shield Box
-
Anritsu's Service Testers and accessories enable OEM aftermarket service and authorized repair centers to troubleshoot and repair mobile phones and data devices quickly and economically. A full range of accessories are available including shield boxes and automation software to provide scalable test capability to the industry.
-
Product
Hall Effect Probes
-
Magnetic Instrumentation manufactures Hall Effect Probes in a wide range of styles and sizes. Probes are supplied with magnetic, electrical, temperature stability and calibration data for each measurement range.
-
Product
Single Event Effects Test System
SEE-RAD
-
The SEE-RAD test system brings together the proven features of our ETS780 tester (such as true APG memory test and powerful FA tools) with the newest technology of the Griffin III. With all new high-accuracy DC Parametrics, superior precision pin drivers, and capture memory of 64M, the Griffin SEE-RAD combines the newest innovations in the test industry with our years of experience in Radiation Test.
-
Product
Hall Effect Systems
-
The MeasureReady™ measurement controller is a revolutionary, all-in-one Hall analysis instrument that delivers significantly higher levels of precision, speed, and convenience to researchers involved in the study of electronic materials.
-
-
Product
Shielding Solutions
-
Antenna Test Chambers are especially designed for testing RF devices and antennas from frequency ranges of 700 MHz to 6000 MHz. These Antenna Test Chambers provide a shielding of more than 90 dB as well as lowest residual passive intermodulation.
-
Product
Hall Effect Magnet Kit
-
Permanent magnet - Neodium materials - +/- 0.03Tesla deviation can be made in a process of assembling magnet. - However, we indicates correct tesla strength measured by gaussmeter, before shipping magnet kit.
-
Product
Hall Effect Measurement system
HMS-3000
-
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Product
Hall Effect Sensors
-
A new range of sensors based on closed loop hall effect technology, for measuring and monitoring of e.g. secondary transformer overload or shortcircuit detection, DC link from ground fault and overload, motor overload.
-
Product
Hall Effect Measurement system
HMS-3300
-
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
Product
Hall Effect Sensors
-
The Mors Smitt transducers are used to measure high currents in rolling stock and trackside applications. High currents are converted linearly to low power signals.
-
Product
AC/DC Hall Effect Sensors
-
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
Product
Hall Effect Sensors
906
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Bi-directional option 906B
-
Product
Electrosmog Shielding
-
Gigahertz Solutions is your partner when it comes to shielding against electrosmog. We offer you products for shielding high-frequency fields as well as products for reducing low-frequency fields. Regardless of whether it is WLAN radiation, mobile phone radiation, Bluetooth or 5G; In our range for shielding from electrosmog you are guaranteed to find the right product with our shielding paints, canopies and shielding fabrics!
-
Product
RF Shield Box
CMW-Z10
-
The R&S®CMW-Z10 has excellent shielding effectiveness and superior coupling characteristics.The shield box can be used for frequencies up to 6 GHz.The antenna structure is optimized to enable excellent radio connections between the DUT and tester.The highly broadband spiral antenna allows a wide variety of applications.These outstanding features combined with modular options make the RF shield box indispensable for any radiocommunications tester.
-
Product
Corona Effect Camera
CoroCAM 8
-
This model of the crown effect camera family is the most advanced on the market. It combines a high specification visible camera, an infrared camera and an ultraviolet camera. The great advantage is the possibility of performing thermal and ultraviolet inspection simultaneously with the consequent benefit in terms of savings (in time and effort).
-
Product
Shielded Chambers
-
GTEMCELL Ltda shielded chambers are built up as a modular construction. Due to individual modules any size of chamber can be realized. Big chambers may require an outer supporting structure or alternatively the shielding material can be attached direct to the building.
-
Product
RF Shielded Box
LTL A6001
-
LTL A6001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A6001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
Powerful and Cost Effective Spectroscopic Ellipsometer
Smart SE
-
The Smart SE from HORIBA Scientific is a versatile spectroscopic ellipsometer for fast and accurate thin film measurements. It characterizes thin film thickness from a few Angstroms to 20µm, optical constants (n,k), and thin film structure properties (such as roughness, optical graded and anisotropic layers, etc).The spectral range from 450 to 1000nm is measured in a few seconds and ellipsometric data are analyzed using the DeltaPsi2 software platform. The software integrates two levels of software to fulfil both routine analysis with predefined recipes and advanced analysis with state-of-the art ellipsometric modelling.
-
Product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
-
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
