Power Test Systems
-
Product
ARINC-708 Module
M4K708
Test Module
The M4K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M4K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive.
-
Product
Selectable Shunt Current Sensor ±40 V, 20 MHz
CX1104A
Power Sensor
The CX1104A selectable shunt current sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 15 A up to 20 MHz bandwidth with an available calibrated resistive sensor head attached
-
Product
Inline Optical Power Meter - PXI
Power 1600 Series
Power Meter
Quantifi Photonics’ Power 1600 Series inline optical power meters provides quick and accurate inline power monitoring. Seamlessly integrate the power meter into your new or existing PXI test setup and save space, lower your costs and improve testing efficiency.
-
Product
Functional Test for Engineering Lab
Spectrum BT
Functional Test
Designed to meet the needs of product engineering labs, production lines, test development centers, and repair depots, the Spectrum BT is a configurable and scalable functional test system. This focused system solves typical functional test coverage challenges throughout the defense/aerospace product life cycle—and it’s upgradable as test requirements evolve.
-
Product
Thermocouple Power Sensors
N8482A
Power Sensor
N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.
-
Product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
Power Supply
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
Product
10 MHz To 67 GHz LAN Thermal Vacuum Compliance Power Sensor
L2067XT
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Regenerative Power System, 2000 V, ±30 A, 20 KW, 400/480 VAC
RP7973A
DC Power Supply
The RP7973A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
High-Performance Autoranging DC Power Module, 60V, 20A, 300W
N6754A
Power Module
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
Laser Diode Reliability Burn-In / Life-Test System
58602
Test System
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
Product
E-Series Average Power Sensor
E9301B
Power Sensor
Measure the average power of all modulation formats Wide dynamic range power measurements from -30 dBm to +44 dBm10 MHz to 6 GHz frequency coverage for Wireless Comms formats Low SWR for reducing mismatch uncertainty Calibration factors, linearity and temperature compensation data stored in EEPROM Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters
-
Product
300-Watt AC/DC Power Supply
Model 56RS1
Programmable Power Supply
NAI’s 56RS1 is a 300 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides a single full-power output at a baseplate temperature of +85° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
Product
10 MHz to 33 GHz USB Wide Dynamic Range Average Power Sensor
U2053XA
Power Sensor
Your product description goes here.The Keysight U2053XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz USB average power sensor.
-
Product
DC System Power Supply, 30V, 25A, 750W
N5745A
Power Supply
The single output, 750W N5745A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current.
-
Product
Power Splitter, DC to 26.5 GHz
11667B
Power Splitter
The Keysight 11667B power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 26.5 GHz allows wideband measurements to be made with a minimum of uncertainty.
-
Product
High Amps, Contact, Receiver, 500+ Amps, 350 MCM
610152101
Power Contact (Receiver)
High Amps, Contact, Receiver, 500+ Amps, 350 MCMContact rated to 1500VDC for low duty test applications.Mating contact 610153102. (NOT compatible with other VPC contacts)Contact ONLY compatible with 310105172 Receiver.
-
Product
Digital Test Instrumentation
EDigital-Series™
Test Instrument
Teradyne’s eDigital IVI driver controls all parallel digital functional test parameters, including per-pin timing, data formats, pattern data, and timing alignment on 64 channels (32 static + 32 dynamic or 32 differential)—each with an 8M pattern depth and results memory.
-
Product
50W Power Supply, 35V, 1.4A or 60V, 0.8A
E3643A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 48W, single output E3643A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
Product
400W 6U CompactPCI Hot-Swappable Redundant Power Supply
cPS-H640/AC
Redundant Power Supply
- PICMG® 2.11 CompactPCI® Power Interface compliant- 6U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 400 W DC output
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
Test Fixture
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Digital Functional Test
CTS100i
Functional Test
Capable of performance testing to defined traceable standards, CTS100i is designed to test Military, Aerospace and Safety-Critical equipment. CTS100i is a cost-effective digital functional test system, available in single, dual and three bay versions.
-
Product
Functional Test Fixtures
Test Fixture
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
Product
6-Position To 4-Position APS-4158/9 Auxiliary Power Cable
788199-0R5
Power Cord
Auxiliary Power Cable for APS-415x, 0.5m
-
Product
160W Triple Output Power Supply, 6V, 10A & 2X 25V, 2A
E36313A
Power Supply
The 160-Watt E36313A is a clean reliable bench power supply for general purpose applications. It combines convenient benchtop capabilities with flexible system features in a compact intuitive package. This is one of three models in this product family. The E36312A (80 W)offers the same feature set with reduced power and the E36311A (80 W) is the most economic model with reduced feature set.
-
Product
Autoranging System DC Power Supply, 1000 V, 30 A, 10000 W, 208 VAC
N8930A
DC Power Supply
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW autoranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' autoranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
Product
Dual Sensor Enhanced Vision Systems
EVS
System
Enhance your safety and situational awareness while flying with Max-Viz dual sensor enhanced vision systems (EVS) from Astronics. These multi-spectral imagers include a long wave infrared sensor, a visible light + near infrared sensor, and patented blending and dynamic range management image processing to enable pilots to see clearly during day and night.
-
Product
Battery Management Systems Testing
System
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
Product
Power Supply, 40V, 125A, 5000W
N8756A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8756A is a 40V, 125A, 5000W, single output power supply in a small 2U package.
-
Product
Power, Patchcord, ITA, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps)
7-251414000-036
Power Patchcord
Power, Patchcord, ITA, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps).
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
