Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
Product
ContactLAB Tester
-
The ContactLAB test platform provides fully configurable reader signal emulation for validation of ISO 7816 contact smart cards and Single Wire Protocol (SWP) USIM for NFC enabled mobile handsets.
-
Product
Oxidation Stability Testers
-
Automatic lubricating oils oxidation stability tester, transformer oil oxidation stability tester, distillate fuel oil oxidation stability tester, gasoline oxidation stability tester (induction period method)
-
Product
HIPOT testers
HypotMAX III
-
Patented SmartGFI® functionStorage of 50 test setupsRemote Safety InterlockUSB/RS-232 or GPIB interfaces availableAdvanced menu driven controlDigitally controlled arc detection systemCHARGE LO® & RAMP HI® systems
-
Product
General Purpose Motor Tester
K302
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test of DC motors and reducer motors.
-
Product
Unclamped Inductive Load Tester
ITC55100STD
-
Model ITC55100STD performs ruggedness testing of power MOSFETs and IGBTs. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
-
Product
Battery Tester
BT-100A
-
Konstar Electric Industrial Co., Ltd
Battery tester can test the car battery whether is ok, if the battery is bad or need chanrge or bad, the tester will give you the right check reasult, then can do the right plan for the battery before work.
-
Product
Scratch/Shear Tester
3025
-
The Elcometer 3025 Scratch/Shear Tester is used to test the resistance of many materials to scratching, shearing, gouging, marring, scraping and engraving.
-
Product
Surge Tester (Impulse Winding Tester)
SS6815 / SS6815F
-
Surge testers (impulse winding tester) is used for testing and check the insulation grade of turns between turns, insulation grade of layers between layers, insulation grade of windings between turns. It is used widely for transformer, current sensor, voltage sensor, relay, contactor, inductor, motor, generator, valve coil, voice coil, etc.
-
Product
Comparison Testers
-
Nagman Instruments & Electronics Pvt. Ltd
Comparison testers are used to compare output of Pressure gauges that are under calibration against the ideal pressure output. They can be used to calibrate all pressure types like Hydraulic pressure (liquid), Pneumatic pressure (Gas) as well as Vacuum. Nagman has a wide range of comparison testers for pressure calibration of any type. Comparison testers are very easy to read and the process is very quick and simple in house pressure calibrations. Nagman’s comparison testers can give you a long life with very minimum maintenance. They are ideal for lab use and in house calibrations.
-
Product
6U Compact PCI Single Board
CP62005
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62005 is a 6U CompactPCI® single board with high-performance, low power consumption and high reliability. It is ideal for ruggedized systems requiring high-bandwidth processing, or for information processing and embedded computing.CP62005 supports 4th generation Intel® Core™ i7 or i5 Haswell processors, up to 16GB onboard DDR3L memory. It also offers 16GB onboard SLC SSD for operating system and drivers. The onboard design of memory and SSD can enhance the anti-shock and vibration performance.CP62005 integrates Intel® HD Graphics 4600 controller, which supports a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA… CRT max resolution is up to 2048x1536. With HDMI/DP/eDP it can be up to 4K. It also supports three independent displays.
-
Product
Hardness Testers
-
The hardness tester products you will find at PCE Instruments (PCE) are used for determining surface hardness. Each hardness tester uses a standard method of measurement. The measuring principles of most hardness tester devices are based on either the penetration of a diamond indentor into the material being tested or a calculation related to the force of the rebound after striking the tested material. However, material hardness can also be measured accurately through ultrasonic testing. Each hardness testing method has its benefits and will allow for the precise measurement of material hardness in accordance with the technical specifications of the hardness testing instrument.
-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
Multifunction I/O
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
-
Product
CPCI-S.0 Standard Compliant Peripheral Carrier Board
MIC-3810
Carrier Board
The carrier board provides a PCIe x16 connector for standard PCIe x8, PCIe x4, PCIe x1 PCIExpress® cards supporting PCIe Gen3 speeds. The carrier board can accommodate cards with maximum dimensions of 176 x 68.9 mm (6.9" x 2.7" inches).
-
Product
Air Leak Testers
-
Leak testing is an important quality control test in the manufacturing industry. Since there is no such thing as a completely leak-free component, the key is to determine what leak rate is acceptable in order to manufacture products that are safe and adequate for the customer’s needs. Once the consequence of a leaking product is determined, it can help guide what type of test method is most practical based on budget and technology required to perform testing at the determined specifications.
-
Product
Digital Safety Tester
-
Is equipped with a high-efficiency PWM amplifier, which isolates the influence of external voltage fluctuations and outputs stable high voltage. Even in areas with large voltage fluctuations, it can achieve "safe" and "reliable" measurements.
-
Product
Gold Tester
-
Napco Precision Instruments Co
Provides the lowest cost option for gold purity analysis needs. A proportional counter system, this the lowest priced X-ray fluorescence unit in the gold tester filed.
-
Product
EMF Testers
-
TES Electrical Electronic Corp.
Frequency range 10MHz to 8.0 GHz3 axis isoltropic measurements of EMFNon-directional measurement with three channel measurment probe. High dynamic range.Configurable alarm threshold and memory function.
-
-
Product
Electric Safety Tester
PVCHECKs
-
The multifunction device PVCHECKs allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
Product
6-400V AC/DC Universal Voltage Tester
1998A
-
Peaceful Thriving Enterprise Co Ltd
This voltage tester is designed for industrial purposes which is suitable for voltage and current circuits.
-
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710-5V-I
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
Drop Tester
AccuDrop 125
-
Model AD-125 is 1 of 3 models in the ACCUDROPTM Series. It helps determine the ruggedness of packagesand the effectiveness of their interior cushioning when exposed to impact during material handling. Theeffects of dropping are easily duplicated in your laboratory using the controlled and precise flat, corner, andedge drop tests.
-
Product
Melt Flow Index Testers
-
Instron® melt flow testers are specifically designed for easy and accurate measuring of Melt Flow Rate (MFR) and Melt Volume Rate (MVR). Our extrusion plastometers range from manual to semi-automated plastic melt flow index testers performing multiple weight tests. All our Melt Flow Index testing equipment meets the latest ASTM and ISO standards.
-
Product
Electronic Load Board 3U CPCI-S (air cooled)
056-377
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
Tabletop Light Fastness Tester
TF419
-
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
-
Product
Digital Insulation Testers
-
Built-in PV dedicated function 600 V AC/ 1000 V DC meter 5 test voltage ranges from 50 to 1000 V Comparator function Integrated hard carrying case
-
Product
Laboratory Battery Tester With Integrated Chamber
-
Compact and versatile, our portable desktop solution integrates Arbin's advanced testing features.
-
Product
Portable Hardness Tester
PHT-1800
-
State of the art, digital portable hardness tester is designed to test the hardness of large hard metal parts. Loaded with useful functions only found on high priced models the PHT-1800 portable hardness tester is clearly setting a new industry standard by being the most accurate, economically priced portable hardness tester on the market today.
