Back Planes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
Product
USB BUS Controller Board
MS 1711
-
- 8 bit and 16 bit compatible Read and Write Cycles- Single or Block Memory and IO Write Cycles- Interrupt Cycle Generation- The generated bus cycles signals is compatible with ISA96 system back plane- External Reset- Double Euro Standard Board- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Intel 80486 DX2 Processor Board
MS 1500
-
- PC 104 bus and ISA bus interface- Facilitates design of scalable architectural solution for Embedded System- Back plane eliminated by self-stacking PC 104 bus- Substantial reduction of development time, cost, as well as risk- Helps to Faster time-to-market / timely product productions- Used for LCA Simulation Project- Intel 80486DX2 @ 33MHz- 512Kbytes of STATIC RAM, 2048 Kbytes of FLASH PROMS- 64 Kbytes of DPRAM- External Interrupts- RS232 Serial Interface- Watchdog Timer- External Bus Interface
-
Product
Back Plane Tester
-
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
Product
Control and Switch Modules
Mini Mux
-
Eclypse International Mini Mux Control and Switch Modules, plus Software Developer Kit (SDK) provides high density test circuit switching as a complement to the Eclypse Circuit Analyzers. The Mini Mux Switching gives the user the ability to test continuity and isolation in complex assemblies with thousands of circuit paths (such as avionic back planes and chassis), while minimizing the test equipment complexity and footprint.
-
Product
Matrix
HLX
-
The HLX™ System is easy to configure to your exact requirements. It distributes HDTV signals up to 1,000 feet away to convenient zone receivers mounted wherever televisions are to be located. For audio systems, the HLX offers DSP and volume control per output (more about HLX for audio). Optional audio zone cards feed multi-channel amplifiers to distribute music to zones. Its robust back plane design allows up to 12 sources to distribute component video up to 1080p, along with analog stereo audio, digital coaxial audio, and digital optical audio. Four audio sources may be added, for a total of 16 source inputs. The new HLX offers a winning combination of performance, value, and unique features.
-
Product
Qualification Hardware & Sockets
-
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
Product
Multifunctional Data Acquisition Systems
MS1201
-
This system used for multi-purpose applications such as data acquisition and Automatic Test Equipment. ATE Computer has ISA Bus based eleven slots with inbuilt power supply. Micro Processor board or USB Controller is used to drive the back plane.
-
Product
ATE Computer
MS 1201
-
This system used for multi-purpose applications such as data acquisition and Automatic Test Equipment. ATE Computer has ISA Bus based eleven slots with inbuilt power supply. Micro Processor board or USB Controller is used to drive the back plane.
-
Product
Signaling Control and Monitor Equipment
MS 1303
-
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
Product
Industry Pack Carriers and Digital I/O
CPCI-4SIP-6U
Digital I/O
The CPCI-4SIP-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4SIP-6U is the perfect solution. There are four (4) Industry Pack sites providing up to 200 I/O pins accessible from either the front panel or the rear back plane.
-
Product
80 Channel Relay Switch
DP-VXI-4503
-
DP-VXI-4503 is a 80 channel, one Form C (SPDT) relay switch designed as a C size VXI module. This high density switch module is designed with a register based interface occupying only one VXI slot. This module uses two Form ‘C’ relay switches. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose.The user can write the command for the selected channels on to the primary latch of the FPGA section. Readback is available to confirm the selected commands. On command, the data from the primary latch is transferred to the secondary latch. The relay driver section provides the necessary drive to switch ON the relays. The buffers in this section drive the relay coils.This module features a back plane trigger for VXI triggered operation. On receipt of the back plane trigger the programmed relays will be energised/de-energised. Alternatively, software trigger can be used.
-
Product
Turning Mirror
10769A
Plane Mirror
The 10769A is ideal for use in laser measurement and calibration applications. In the calibration of slant bed lathes, for example, the beam steering mirror deflects the beam from the laser head upward, through the interferometer, along the lathe's cross slide. One or more mirrors can also create a path from a laser head to an interferometer located in an otherwise inaccessible position, as in the case of a milling machine with a table that moves in only one axis.
-
Product
Turning Mirror
10772A
Plane Mirror
The Keysight 10772A Turning Mirror is a 100% reflectance mirror that turns the direction of an incoming laser beam 90 degrees. The mirror is used in the 5530 Laser Calibration System for applications such as machine tool calibration. It can be used in place of the 10707A Beam Bender (6 mm or less beam diameter) for applications that require the larger aperture of the 10772A.
-
Product
Turning Mirror on Universal Mount
10769B
Plane Mirror
The Keysight 10769B Turning Mirror on Universal Mount deflects a laser beam at any angle, in either the vertical or the horizontal polarization plane of the beam. The 10769B contains the same turning mirror as the 10769A, but has a different mounting.
-
Product
Spring Back Tester
HTJ-16
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.4-2008Used to measure the spring back characteristic of enameled round wires with nominal conductor diameter of between 0.080mm and 1.600mm;Number of winding turns: 5 turns and a halfStop accurately at zero position of the scale after automatic windingAs soon as the value of spring back angle stop counting, the dial will stop to rotate immediately, so that the value displayed on LED and read on the dial are the same.Sensor is unnecessary to be adjusted for samples of different specificationsCoils loosen slowly during spring back, no action of spring back or jump suddenly.Application of SCM control allows for fast operation and strong anti-interference capacity;
-
Product
High Stability Plane Mirror Interferometer
10706B
Angular Interferometer
The Keysight 10706B High Stability Plane Mirror Interferometer is a dual pass interferometer used for multiple axis applications such as X-Y stages where the measurement mirror may move perpendicular to the measurement axis. This thermally stable optic, an exact functional replacement for the 10706A Plane Mirror Interferometer, reduces thermal measurement drift to 1/12 the value typically achieved by conventional plane mirror interferometers. The unique contribution of the 10706B is its tolerance of angular misalignment of the plane mirror reflector. The 10706A can accept a range of measurement mirror angular alignment changes.
-
Product
30" Front to Back Stiffeners
FB-30
-
Additional aluminum extruded front-to-back stiffeners are available for Vertical Cabinets. Includes installation hardware
-
Product
Back Pressure Tester
TU29P
-
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
Product
Plane Mirror
10728A
Plane Mirror
The Keysight 10728A is a normal incidence plane mirror for beam diameters of 9 mm or less. It is a bare optic that requires a user-supplied mount. It is typically used with the 10735A and 10736A three axis interferometers.
-
Product
Mini Back Probes/Wire Piercers
618
-
*Great for backprobing weather pack style connectors used with numerous automotive sensors *Also very handy for piercing and tapping readings on smaller gauge wires - using the included probe adapters *Works with most Test Lead Kits in the field - with standard 4mm banana plug test lead *Set includes four probes - red, black, green, yellow Test probes 21 mm length
-
Product
Multi-Sensor In Plane
MS 1000-IP-20
-
Advanced Thermal Solutions, Inc.
The MS 1000-IP-20 is a three-sensor probe designed for measuring fluid velocity and temperature in the same vertical plane. It eliminates the need for multiple probes or a traversing probe for determining the flow profile or distribution.
-
Product
Push Back Probes (VF4) HVF4
1001841
-
The Push Back Probes (VF4) HVF4, identified by Order code 1001841, are innovative components designed to enhance the functionality of electrical systems. With precise measurements of a total length of 34.00 mm, these probes are engineered with optimal performance in mind. The press ring diameter of 3.70 mm and outer diameter of 3.50 mm ensure a snug fit within various receptacles, while the collar height of 5.70 mm facilitates secure connections. This robust design caters to a variety of industrial applications, promising reliability and longevity in demanding environments.
-
Product
Push Back Probes (VF3) VF305B300G15
1005905
-
The Push Back Probes (VF3) VF305B300G15, with order code 1005905, represent a hallmark of precision and reliability in contact probing technology. Designed for varied applications, these basic contact probes are engineered to endure extreme temperature ranges from -45°C to +100°C, ensuring consistent performance in challenging environments. With a pitch measurement of 3.00 mm (118 mil), they deliver reliable connectivity and efficient signal transfer across diverse use cases. The robust construction employs high-grade materials such as beryllium copper for the plunger, plated in gold for enhanced conductivity, while the brass barrel, also gold-plated, ensures durability and anti-corrosion.
-
Product
Push Back Probes (VF4) VF417B400G15
1009400
-
The Push Back Probes (VF4) model VF417B400G15 is engineered for high precision and reliability in demanding electrical applications. Designed with a basic contact probe style, this product can withstand extreme temperatures ranging from -45°C to +100°C, making it suitable for versatile operational environments. With a pitch of 4 mm, it ensures compatibility across various devices, enabling engineers to easily integrate it into their systems for optimal performance. The use of high-quality materials such as beryllium copper and gold plating for the plunger ensures durability and excellent conductivity, which is essential for maintaining low contact resistance at 30 mΩ.
-
Product
Push Back Probes (VF3) VF317B180G15
1005301
-
The Push Back Probes (VF3) VF317B180G15 is a highly specialized contact probe designed for precise electronic applications. With a pitch of 3.00 mm, these probes are capable of operating within a temperature range of -45°C to +100°C, making them suitable for various environments. The probes feature a robust design with a basic contact configuration that ensures reliable performance under continuous currents of up to 8.00 A, with a typical contact resistance of only 30.00 mOhm.
-
Product
Push Back Probe (VF4) VF483B0001G15
1005203
-
The Push Back Probes (VF4) VF483B0001G15 are designed for high performance in various applications, extending their utility across multiple industries. With a basic contact probe design, these probes offer a pitch of 4.00 mm (157 mil) and are built to endure a wide temperature range from -45°C to +100°C. They are engineered to deliver reliable results, showcasing a continuous current rating of up to 10.00 A and maintaining a typical contact resistance of just 30.00 mOhm, ensuring optimal conductivity and minimal energy loss.
-
Product
Push Back Probes (VF3) VF306B300G05
1006281
-
The Push Back Probes (VF3) VF306B300G05, with order code 1006281, are high-performance basic contact probes designed to meet various demanding applications. Engineered for precision, these probes operate within a temperature range from -45°C to +100°C, ensuring optimal performance in challenging environments. With a pitch of 3.00 mm and continuous current handling of up to 8.00 A, these probes deliver reliable electrical connectivity and minimal contact resistance, typically at 30.00 mOhm. This makes them an excellent choice for applications that require accurate and durable connectivity.
-
Product
Push Back Probes (VF4) VF483B0010G03
1016564
-
The Push Back Probes (VF4) VF483B0010G03 are engineered for precision and reliability in various applications, showcasing their versatility and technical sophistication. With a pitch of 4.00 mm (157 mil), these probes are designed to perform effectively within a temperature range of -45°C to +100°C. The S1 additional designation ensures compatibility across different systems, making them an ideal choice for specialized operations where accuracy is paramount. This model is characterized by a mechanical preload of 80 cN and an impressive spring force of 300 cN, supporting a nominal travel distance of 5.00 mm with a maximum allowable travel of 5.50 mm, facilitating precise engagement with contact points.
-
Product
Push Back Probe (VF4) HVF4DS-57
1010458
-
The Push Back Probes (VF4) HVF4DS-57 is a versatile solution designed to meet a wide range of applications, ensuring reliable performance under various conditions. With a precision-engineered design and robust construction, these probes provide the right balance of durability and effectiveness, making them ideal for both industrial and technical settings. The HVF4 series offers advanced capabilities tailored to enhance operational efficiency, reflecting the quality that is expected from such components.
-
Product
Manage Power, Thermal & Control Planes In Real Time
Platform Manager 2 & L-ASC10
-
*Full fault coverage – monitor all rails and temperature nodes*Manage from 10 to 80 supplies using just the required number of L-ASC10 hardware management expanders*Minimize fault propagation by enabling individual hardware management sub-blocks (power, thermal & control path) to respond to faults in other blocks within nano-seconds*Save CPLD I/O pins by eliminating the need to monitor power-good signals of DC-DC converters*Reliable power & thermal fault detection in hardware, as opposed to software routines
