Filter Results By:
Products
Applications
Manufacturers
Tachometers
Measure number of rotations over time.
See Also: Tachometer Testers, Engine Tachometers, Motor Rotation
-
product
Contact Type Handheld Digital Tachometer
HT-3200
The HT-3200 offers a Lo measurement range that starts from 0.5 r/min. The circumferential ring and contact tip for rotation measurement can be stored in the back-side pocket of the main body.
-
product
Digital Tachometer / Lengthmeter
EHT-600
The EHT-600 Digital Tachometer / Lengthmeter features exceptional resolution at low speeds. The EHT-600 is easy to use and is built with an ergonomic metal housing and operates on two standard AA batteries. The tachometer is small enough to be carried in a pocket.
-
product
Laser Tachometer
LaserTach™
The LaserTach™ ICP™ tachometer senses the speed of rotating equipment and outputs an analog voltage signal for referencing vibration signals to shaft speed. The sensor allows for measurements in excess of 30,000 RPM from distances as far as 20 inches (51 cm).
-
product
Diesel Engine Tachometer
GE-1400
Handheld type digital engine tachometer to be designed for dedicated r/min measurement of 4-cycle diesel engines. R/min direct reading measurement is available only by clamping a CP-044 Diesel Engine Rotation Sensor (sold separately) to a fuel injection pipe.Both analog (switchable between analog and monitor output) and pulse outputs are provided; enabling to use analog output for data recording (monitor output for sensor waveform checking or analysis input signal of FFT analyzer), and to use pulse output for tracking analysis signal of FFT analyzer.
-
product
Tachometer Indicator-Generator Testers
Tachometer Indicator-Generator Testers by Hydraulic Technology
-
product
Digital Input/Output Expander (Normally-Open Relay Contact Outputs)
ENVIROMUX-DI16DOR16
Adds 16 digital inputs and 16 digital normally-open relay contact outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for normally-open relay contact outputs. Accepts 26 to 16AWG wire. Potential free. Rated switching load: 0.5A @ 125 VAC, 1.0A @ ±30VDC. Fused. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Includes 5V/3A power supply. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.78 in (165x79x45 mm). Regulatory approvals: RoHS.
-
product
Hour Meters
Global Digital Instruments, LLC
GDI manufactures hour meters with multiple inputs and mounting styles making them suitable for a broad range of applications. Hour meter options include: Inductive input, AC/DC input, Vibration Activated and Rotating Shaft Tachometer and hour meter.Hour meters are used within a variety of industries where equipment is regularly used. They are useful for determining when regular maintenance is needed to help extend the life of the machine.
-
product
Anemometers/ Tachometers
TES Electrical Electronic Corp.
Fast response propeAir flow volumeInstant/ avg/ V max flow measurement. VelocityTemperature and Humidity measurement. Calculate Dew point temperature, Wet bulb
-
product
5000
White Series
The Equus 5000 series white 5" pedestal mount tachometer offers excellent street performance value featuring classic performance tach design, compatibility with most 4,6, and 8 cylinder engines equipped with conventional peformance ignitions.
-
product
Digital Tachometer
RM-1500 /RM-1501
5 Digits LCD Display. Light Reflex Measurement. Range from 10.00 to 99,999 RPM. Measuring Distance 50 to 300 mm. Event Counter elapsed time. Max/Min/Hold : True Average
-
product
TAKCAL Tester
H391T-56-1
Measures and displays individual tachometer speeds in percent RPMConnects at flight deck navigator station for signal and at St245 for power
-
product
Tachometer Tester
Series 1921
The Model 1921 Tachometer Tester is used for the testing and calibration of electrical and mechanical tachometer generators and indicators.
-
product
Mark II Dual Setpoint Monitor
95006
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
product
Digital ICP® - USB Signal Conditioner
The Digital ICP®-USB Signal Conditioner, Model 485B39, offers plug-and-play connectivity for your measurements. Model 485B39 from The Modal Shop, a wholly owned subsidiary of PCB Piezotronics, is a pocket-sized, dual-channel ICP to USB digital signal conditioner. The unit provides any ICP sensor – accelerometers, microphones, impact hammers, laser tachometers, and more – with a digital USB output. It is truly plug-and-play, with no drivers required. Digital ICP features two BNC inputs and a 24-bit USB digital signal output, allowing a direct connection from the sensor to any PC, tablet, or smartphone device for easy data collection, analysis, and sharing on-the-go.
-
product
Process Tachometer
TCT101-3ABC
The Process Tachometer TCT101-3ABC is a panel mount Process Tachometer which can measure frequency up to 100Khz with Encoders and 2 or 3 wire proximity switches. There is also a function to store the maximum frequency and the lowest frequency.
-
product
Laser Type Tachometer
DT-2857
MEASUREMENT RANGE:2.5～99,999r/min. ACCURACY:±(0.05%n+1d) . POWER SUPPLY:4X1.5V AA(UM-3)BATTERY
-
product
Tachometer Indicator-Generator Testers
Hydraulic Technology Tachometer Indicator-Generator Testers
-
product
Turbine Logging System
This Turbine Overspeed Trip Logging system has been developed to check the operation of steam turbines. The speed of the turbine is monitored using an optical sensor, the logging system can be mounted up to 30 meters from the sensor. This allows the overspeed trip speed to be monitored and recorded with greater safety that using a simple tachometer. The results are logged together with time and date stamp so that it can be demonstrated that the test has been carried out.
-
product
Tachometers
Sanwa Electric Instrument Co., Ltd
an instrument that measures the working speed of an engine (especially in a road vehicle), typically in revolutions per minute.
-
product
On-Board Flow Meter
DF-2200
The DF-2200 On-Board Flow Meter is a compact on-board fuel flow meter developed for our FP series Volumetric Flow Detector*. The compact body is equipped with functions such as flow rate/temperature/pressure measurement and CAN communication required for fuel consumption measurement. Adopting the same size as our CT-6700 Engine Tachometer, it can be used by stacking two units in a limited space. In addition to 12 to 24VDC of power source, an AC adapter is available as an option, which is sufficient for not only on-board measurement but also engine bench evaluation.
-
product
Tachometers
SHIMPO offers a wide range of hand-held tachometers that measure the total number of revolutions of a shaft or number of pulses of reciprocating equipment. Our models can measure and record last/min/max and up to 10 reading using up to 16 different units of measure. Our tachometers are designed for applications such as Motor Speed/Conveyor Speed/Fan Speed/Length Measurements that measure rpm of motors or shafts, either contact or non-contact with Laser style combination tachometer.
-
product
Ignition Pulse Detector
IP-292/296
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
product
Process Panel Meters
Rugged and reliable, the 1/8 din panel meter line is designed for both the OEM and retrofit markets with an array of flexibility enabling usage in a broad range of applications. Our Panel Mount Tachometers are ideally designed for speed, rate or time monitoring applications with potential connection to PLC’s and networks with available outputs. The dedicated Process Meter line-up allows usage in virtually any application with their voltage, current or temperature input selections along with a myriad of optional output signal and communication combinations. The similarly designed Process Counter line completes the offering, geared for frequency or encoder input applications.
-
product
Tachometers, Counters & Displays
Displays Include; Rate, Time In Process, Product, Sum, Difference, Ratio, Draw Process, Batch, or Total Counting. Field Adjustable, Full Diagnostic Functions. Built-In Relay Testing Capabilities. Highly Programmable. Single-Channel or Bi-Directional Counting. Setpoint and Start Delay Functions. Multiple Relay and Analog Output Options. Keypad Lockout
-
product
Tachometers
Guangzhou Amittari Instruments Co.Ltd
The Multifunction Tachometer Used to test the rotative velocity ,surface speed or frequency of motor.Widely applicable to motor, fan, paper-product ,plastics,chemical fiber,washing-machine,automobile,airplane,steamer department etc.
-
product
512 Channel Systems
Spider-80X/Spider-80Xi
The Spider-80X is designed for applications in three fields: dynamic data acquisition, vibration control, and machine monitoring. Each front-end features eight analog input channels and two channels that may be software selected as analog outputs for vibration control or tachometer inputs for the analysis of rotating machinery.
-
product
Counter/Timer Board
MSXB 036
The MSXB 036 Counter/Timer Board is used for frequency counting, rotational speed (tachometer) measurement, and closed loop process control based on frequency criteria. Engine performance monitoring is a typical application. The Counter/Timer Board provides 16 digital input lines and 16 digital output lines, counts up to 6 MHz on 10 channels, and has two 100 MHz frequency prescalers.
-
product
Gasoline Engine Tachometer
SE-2500A
SE-2500A is a non-contact handheld tachometer designed for gasoline engine measurement. Detection, measurement, and display parts are all in one unit and batteries are built in the unit. Moving the detector (head of the SE-2500A) close to an ignition coil can measure rotation speed at the unit of 1 r/min or 0.01 r/s. Up to 20 measurement data can be stored in the internal memory that is convenient for later checking.
-
product
Tachometer & Anemometer
ZhangZhou Weihua Electronic co.,ltd
a Tachometer (measure RPM of turbine blades) and an Anemometer (measures wind speed).
-
product
Diesel Engine Tachometer
GE-2500
The GE-2500 diesel engine tachometer uses rotation speed of an alternator to measure engine rotation speed. With FFT calculation, this tachometer achieves reliable and stable measurement for both diesel and gasoline engines.The OM-1500 is a compact type detector designed for measuring rotation speed of an alternator. It detects magnetic flux leakage from an alternator. It is used to combine with the GE-2500. (The OM-1200 can also be used with the GE-2500.)
