Totalizers
-
Product
NI-9326, 6-Channel, 150 V, 128 kHz C Series Frequency Input Module
786999-02
-
6-Channel, 150 V, 128 kHz C Series Frequency Input Module - The NI-9326 is a channel-to-channel isolated frequency input module for CompactDAQ and CompactRIO systems. This module includes six differential input channels with a 0 Vrms to 150 Vrms input range. The NI-9326 also features configurable thresholds for connection to a variety of variable reluctance sensors, single channel encoders, and hall-effect sensors. You can use the included embedded counters to perform frequency measurements or edge-counting for tracking total counts on a periodic signal. Additionally, the NI-9326 supports configurable Butterworth filters to help you perform low-noise frequency measurements.
-
Product
Oscillators - Voltage Controlled
-
Teledyne RF & Microwave offers Voltage Controlled Oscillators (VCOs) utilizing bipolar transistors & silicon varactors over the frequency range of 40 MHz to 18GHz. Many of the VCO designs incorporate internal filtering, regulation & amplifiers to meet total system requirements in a small integrated package. Additionally, our hermetic hybrid designs can be screened to the most demanding military and space applications.
-
Product
THC-CH4-NMHC Analyzer
Model N901
-
Teledyne Advanced Pollution Instrumentation
The Model N901 is a near-continuous hydrocarbon gas analyzer that measures the concentration of Methane (CH4) and Total Hydrocarbons (THC) in air. The concentration of the non-Methane (NMHC) component is calculated by the subtraction of CH4 from THC, with high sensitivity and accuracy. The hydrocarbons are measured using a Flame Ionization Detector (FID), in combination with gas chromatography (GC). The instruments range and performance are tuned specifically for use in ambient air quality monitoring assessments.
-
Product
PC Based Test Setup for LED Driver of LED
-
The tests are Performed as Prescribed in IS the Panel Carries out high voltage, open circuit and performance tests, one by one and provides indication of the Test results as PASS or FAIL lamp for high voltage test. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 80 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. The entire system is housed in sturdy M.S cabinet with powder coating.
-
Product
PRO High Range Total Dissolved Solids Meter
MW402
-
MW402 is a Portable Conductivity High Range (TDS) Meter with Automatic Temperature Compensation. This instrument has been designed for aquariums, aquaculture, labs, and water conditioning applications to meet the needs for equipment suited from hobbist to professional. It is also a great meter for food labs, and water treatment applications.
-
Product
Image Intensifiers
-
Image intensifier tubes (IITs) are vacuum tubes that amplify a low light-level image to observable levels. Image intensifier tubes are the most important modules of night vision devices that play crucial role in defense/security/industrial applications.Technology of manufacturing of image intensifier tubes is very difficult and performance parameters of modern IITs varies even within the same technological process. Next, test report offered by manufacturers cannot be fully trusted because there are some differences in test methods used by different manufactures. Further on, there are literature sources presenting conflicting claims of different manufacturers. It is quite common to find on the world market two night vision devices (or two image intensifier tubes) of the same data sheet parameters but of totally different image quality. Inverse situation is possible, too. Due to reasons mentioned above testing image intensifier tubes is of critical importance for both their manufacturers, manufacturers of night vision devices (NVDs) and final users of NVDs.
-
Product
Coating System
Precisioncoat V
-
The redesigned SCS Precisioncoat V provides more than a dependable layer of protection, it is a total system solution that ensures accuracy, repeatability and high throughput for a wide range of automated material application, all in a smaller footprint to maximize valuable production floor space. It is the culmination of more than 40 years of experience in design and manufacturing high performance liquid coating systems. It incorporates both the engineering expertise and application experience that make SCS a leader in conformal coating technology.
-
Product
AC Source
5310（0~500Vrms/1KVA）
-
Voltage output has totally six ranges，maximum up to 500V，convenient for 300V above the voltage regulation test
-
Product
X-Ray Components
-
Photonis designed the Micro Pore Optics detector to be used in X-Ray imaging applications. Its perfectly square, flat channels are optimized to allow X-Ray and UV photons to be focused or collimated due to the total external reflection at a grazing angle (<2°). Micro Pore Optics are installed on a number of international space missions.
-
Product
Conductivity-Thermometer Data Logger
HD2106.2
-
Conductivity-Thermometer measures conductivity, liquid resistivity, total dissolved solids, salinity and temperature. Datalogger which can store the maximum, minimum, average value and can store up to 36,000 samples.
-
Product
Data Acquisition Control Boards
X-GCU
-
X-GCUs are a data acquisition and control boards of Detection Technology’s digital X-ray detector platforms. X-GCU together with the digital X-Cards provide complete and easily scalable detector subsystems shortening time-to-market and delivering total cost savings for all types of X-ray imaging systems.
-
Product
Very Compact Low-Frequency Control Element
750-LFC
-
The 750-LFC low-frequency-control element’s impressive power-to-size-ratio and versatile features make it the right choice for any application demanding superior low-frequency performance in low-profile systems. It pairs perfectly with ULTRA‑X40 and LINA systems, extending response down to 36 Hz for deeper, richer bass with total control.
-
Product
Total Reduced Sulfur System
ML670
-
The ML®670 Total Reduced Sulfur (TRS) system provides an accurate and convenient method of measuring Total Reduced Sulfur required for Emission Monitoring. The TRS system uses our specially designed TRS Dilution Sampling System combined with the T-Series® TRS analyzer to provide reliable TRS measurement. This system can be configured as an Open Architecture Design for ease of maintenance.
-
Product
7-Ch Thermocouple Input Module
ADAM-5018
-
Accuracy Bandwidth: ±0.1% or better, 13.1 Hz @ 50 Hz, 15.72 Hz @ 60 HzSampling Rate: 10 samples/sec. (total)High Common Mode: 2000 VDCIsolation Voltage: 3,000 VDCFault and Overvoltage Protection: Withstands over voltage up to ±35 VCMR @ 50/60 Hz: 92 dB minInput Impedance: 20 MΩ. (Build-in 120 Ω Register for Current Input)Built-in TVS/ESD ProtectionFilter function: Yes
-
Product
4 MP OV4682 RGB IR Camera Module
e-CAM40_CUMI4682_MOD
-
The e-CAM40_CUMI4682_MOD is a 4 MP RAW RGB-IR MIPI OV4682 camera module with the M12 S-mount lens holder. The e-CAM40_CUMI4682_MOD RGB IR camera module is based on OmniVision's OV4682 1/3" Optical format CMOS Image sensor, that captures high-resolution images and videos as well as IR information. Its dual RGB-IR Camera capabilities allow it to bring a host of additional features to machine vision applications and by combining RGB - IR in a single camera module reduces the total cost and saves space. Customers can evaluate e-CAM40_CUMI4682_MOD with See3CAM_CU40 over USB 3.0 interface and e-CAM40_CUTK1 over MIPI interface. e-CAM40_CUMI4682_MOD camera module can stream the 4MP(2688x1520) unprocessed 10-bit RAW data video upto 40 fps. Also read OV4682 RGB IR camera module frequently asked questions.
-
Product
Magnetostatic probe
BS13
-
Three-dimensional measurement of magnetic equationsMeasuring range 100 TResolution 0.1 TAbsolute and relative measurementsFor connection to the field meter FM10Switching between total field strength and X, Y and Z proportions is possiblePermanent recording and saving of individual points with the field meter FM10LOutstanding value for moneyDimension 132 x 40 x 25 mm
-
Product
Marine Ballast Water Analyzer
9017
-
Developed specifically for the demands of marine environments, OI Analytical's new Model 9017 Marine Ballast Water Analyzer was engineered to meet the stringent United States Coast Guard (USCG) standards. The 9017 monitors and controls total chlorine and residual oxidants around the clock, while connected to a Ballast Water Management System with user-programmable cycle times and alarms.
-
Product
Surge Arrestor Testing Equipment
SA 30i+
-
SA 30i+, the wireless Leakage Current Analyser from SCOPE is a State of the Art, On-line test system for Residual Life Assessment of Metal Oxide Surge Arresters. The instrument measures and directly displays the values of Total Leakage Current and Third Harmonic Resistive Leakage Current. It provides system harmonic compensation as per IEC 60099-5-B2. It provides Corrected Resistive Leakage Current after applying correction factors for change in system voltage & temperature.
-
Product
Acute 2GHz, 34 Channel, TravelLogic Series Protocol & Logic Analyzer With 8Gb Memory
Acute TL4234B
-
The TravelLogic Series of Protocol & Logic Analyzers are small enough to fit into your shirt pocket, yet are truly sophisticated logic analyzers, capable of 2 GHz timing analysis, or 200 MHz state analysis, with up to 8 Gb total stackable memory for the 34 channels. They plug into a PC or Laptop USB port making them ideal for the field service technician or engineer, hopping from PC to PC, or taking with them for diagnosis on the road. Also remember that with USB, no additional power supply is needed.
-
Product
96-CH High-Driving DIO Card
PCI-7396
-
The PCI-7396 is 96-bit parallel digital input/output (DIO) cards designed for industrial applications. The PCI-7396 emulates four 8255 Programmable Peripheral Interface (PPI) chips. Each PPI offers three 8-bit DIO ports which can be accessed simultaneously. The total 12/6 ports can be configured as input or output independently.
-
Product
Breakout Box
T1000-15
-
T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
Product
Burn-in Systems
-
Incal Offers A Line Of State-Of-The-Art Burn-In Testing Hardware And Software For Retrofit And/Or Total, Customized Burn-In System Configurations.
-
Product
Fault Locating
-
Schweitzer Engineering Laboratories, Inc.
The built-in fault-locating methods in SEL devices allow you to quickly identify faults, dispatch crews for repairs, and restore service faster. Traveling-wave fault-locating technology calculates the locations of temporary and permanent faults by measuring the arrival times of the naturally occurring traveling waves caused by a transmission line fault. Accurately detecting these waves requires ultra-high-resolution monitoring, and locating is accurate to within one tower span (±300 m). Impedance-based fault-locating technology calculates fault locations by detecting changes in line impedance as a result of a fault. Impedance-based locating is reliable and accurate to about 2 percent of a line’s total length.
-
Product
Magnetostrictive Level Transmitter
DM231
-
The Drexelbrook DM231 is an explosion proof liquid level transmitter offering high accuracy measurements based on the magnetostrictive sensing technology.The DM231 comes with a Modbus RTU digital output (optional analog output converter available) for total level, interface level and temperature sensor outputs. Sensors are available in 316SS rigid designs with a choice of single or dual NPT mountings. Temperature sensors are evenly distributed over the active length of the rigid 316SS tube.Due to a wide selection of floats and mounting accessories this level transmitter fits virtually any application.The DM231 level transmitter is FM approved for Class 1 Div. 1, Zone 1 Explosion Proof hazardous area installations. It is easy to install and requires no calibration.
-
Product
Flexible Implantable Microprobe
IT-18EXLONG
-
IT-18EXLONG Flexible Implantable Microprobe with 5 foot lead - Implantable in semi-solids and tissue with 18 gauge needle (supplied). Also for immersion in various solutions and rectal temperatures of small animals. Totally sheathed in chemical resistant Teflon™. Quited rugged. Maximum Temperature 150°C . Isolated. Probe diameter .050" (14 gauge represents the needle gauge that the probe can be inserted through). Time constant 0.3 seconds.
-
Product
Electromagnetic Total Counters
MCF Series
-
Economical electric totalizer with Push button reset. Bail, rear or base mount. Compact for limited space installations.
-
Product
Universal Counter
U6220A
-
The Picotest U6200A also provides great features including Frequency & Ratio (11Digits/Sec.), Time interval, Period (2.5 ns to 1000s), Duty Cycle, Pulse Width, Rise/Fall Time, Peak Volts (100 Hz~300 MHz), Phase, Totalize, Temperature Stability (< 1 PPM), Aging Rate (< 2 PPM per year), timebase reference channel (Figure-2) and complete Front-End Isolation. Moreover, it offers 20 memory locations (Figure-3) for storing frequently-used operations.
-
Product
Power Line Meter
-
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
Product
Programmable DC Power Supply
SPD3303C
-
The SPD3303C is a LED display screen programmable linear DC power supply that is both lightweight and feature-packed. It has three independent outputs: two sets of adjustable voltage and a fixed set of selectable voltages; 2.5V, 3.3V, and 5V. In addition, the ‘3303C has outputs that are short-circuit and overload protected. Total power is 220W. It has three available operation modes; independent, series and parallel modes. The SPD3300C has a high performance-to-price ratio and can be used in various types of production, education and research environments.
-
Product
Open Pluggable Specification (OPS) Digital Signage Player With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170 And Intel® AMT 11.0
OPS500-501
-
The OPS500-501 is a 4K resolution OPS compliant digital signage player supporting Intel® Active Management Technology (AMT) 11.0 for better remote management. The space-saving OPS signage module is powered by the 6th generation Intel® Core™ processor with Intel® Q170 chipset. It has one 260-pin DDR4-2133 SO-DIMM socket with up to 16GB memory capacity. Compliant with the Intel® OPS architecture, the 4K-ready signage player provides a high level of compatibility as well as simplified installation, maintenance and deployment for a lower total cost of ownership. The outstanding digital signage player, the OPS500-501, is connected to OPS-compliant display via a standardized JAE TX-25A plug connector that supports DisplayPort, HDMI 2.0, UART, audio, USB 3.0 and USB 2.0 signals. To meet various application needs, the powerful digital signage system offers rich I/O interfaces on its front panel, including one USB 2.0 ports, two USB 3.0 ports, one COM port, audio (in/out), HDMI and a Gigabit Ethernet port. This space-saving OPS signage player has one PCI Express Mini Card slot for WLAN connectivity and features one 2.5” SATA HDD for extensive storage needs.
