Proto Boards
-
product
FMC Add-On Cards
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
product
NI-9485, 8-Channel, SSR Relay, 60 VDC/30 Vrms, 750 mA C Series Relay Output Module
779600-02
The NI-9485 allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to a solid state relay (SSR) for switching voltages up to 60 VDC/30 Vrms with switching current up to 750 mA per channel or up to 1.2 A on four channels. Each channel also features channel-to-channel isolation.
-
product
PCI Three-Axis High Performance Laser Board with External Sampling
N1231B
The Keysight N1231B PCI Three-Axis Laser Board with External Sampling is a register based PCI bus board that implements three axes of laser interferometer measurement for position monitoring and closed-loop servo control. There are four external sample inputs along with four data hold inputs that allow easy synchronization with user systems. Several threshold compare registers, with both hardware outputs and interrupt capability, can be used for travel limit and in window or out of window detection functions. The dual mode hardware position outputs, controlled by the hold inputs, provide either a 32-bits/axis parallel interface or a 36-bit multiplexed interface to the 36-bit axis position data at rates up to 20MHz. The user can programmatically access the externally sampled position and velocity data, as well as software sampled position and velocity data, over the PCI bus at rates up to 100kHz (3 axes of position and velocity) or 200kHz (position or velocity only).
-
product
FPGA Processing Board
VP880 / VP881
The VP880 / VP881 is a high-performance FPGA processing board featuring Xilinx® Ultrascale™ and Zynq® Ultrascale+™ technology. It is designed for the most demanding, mission critical military/defense applications such as electronic warfare / DRFM, radar/sonar image processing, satellite communications systems, multichannel digital transmission/reception and advanced digital beamforming.
-
product
COM-HPC Server Type Reference Carrier Board in Extended ATX Form Factor
COM-HPC Server Base
The COM-HPC Server Base is an extended ATX size COM-HPC Server Type reference carrier board based on PICMG COM-HPC Revision 1.0. Together with the COM-HPC Server Type module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
PXI Express Optical FPGA Board
HSS-8324
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
product
Board
Arduino Leonardo with Headers
The Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
-
-
product
Overhead Board
OVH-380-2
Curtiss-Wright Defense Solutions
The OVH-380-2 is the enhanced overhead board for the AIM/ HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers, and terminates the IP stack for Ethernet support. It also receives and formats inbound (acquired) data.
-
product
Training Board
JT 2156
The JT 2156 training board has been devised to demonstrate all the latest features and test techniques available to users of JTAG Technologies’ ProVision & JTAG Live application development systems. As well as a modern ARM Core processor, the design also includes an Altera Cyclone FPGA, DDR Memory, Ethernet PHY, and several SPI and I2C peripheral parts. The JT2156 is shipped with a comprehensive self-study manual for getting to know the in-depth features of ProVision and/or JTAGLive Studio. For Altium users the design also serves as an example of how to adapt the Nano board into a realistic custom design.
-
product
RFSoC Board
VP430
RFSoC on 3U VPX: the VP430 direct RF system features an RFSoC with integrated ADCs, DACs, programmable FPGA logic, and Zynq ARM Cortex processor.
-
product
Demonstration Board
SAMPULSE20x2
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
product
Sampling Boards
MSXB 028
Simultaneous Sampling Boards are used in multichannel spectral analysis and other applications that require simultaneous acquisition of several channels. The MSXB 028 usually is used for applications that require interchannel phase measurements such as applications that perform transfer function computations. This board eliminates phase error introduced by sequential sampling.
-
product
GPGPU Board
NVP2000
The Abaco NVP2000 is a chip-down 3U XMC graphics output and GPGPU card based on the NVIDIA® Pascal ™ (GP107) Quadro® P2000 GPU. The NVP2000 leverages the high performance of the GPU with its 768 CUDA cores and 4GBytes of GDDR5 memory to deliver 2.3 TeraFLOPs of peak performance with CUDA™ and OpenCL™ support.
-
-
product
Carrier Boards
Advantech Development boards provide a schematic software & reference design to reduce efforts needed in development stage. Advantech Development Board can be used to test carrier board problems and support COM series, and Qseven, ETX / XTX form factors.
-
product
PCI Board
FastX1703-DIG
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
product
Overhead Board
TTC OVH-380-1
Curtiss-Wright Defense Solutions
The TTC OVH-380 is the processor-based controller (overhead) board for the TTC AIM/HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers and terminates the IP stack for Ethernet support.
-
product
3U CompactPCI Serial MXM GPU Carrier Card
cPCI-A3MXM
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP/8HP (100mm x 160mm)- Compatible with MXM Type A (82 mm x 70 mm) or Type B (82 mm x 105 mm)- Support NVIDIA A1000 with 2048 CUDA® cores, 16 RT Cores and 64 Tensor Cores or NVIDIA RTX™ A4500 with 5888 CUDA® cores, 46 RT Cores and 184 Tensor Cores- 4x DisplayPort 1.4, support 4K (3840x2160) resolution- Operating temperature: -40°C to +70°C- Designed to meet EN50155 standards
-
product
GPGPU Board
NVP2009
As part of our NVIDIA Pascal™ based chip-down series of GPU XMC products the NVP2009 is ideal for GPGPU applications such as C5ISR, situational awareness, signal intelligence (SIGINT), as well as machine learning and autonomy.
-
product
Carrier Boards
ROM-DB7500
ROM-DB7500 is an Evaluation Carrier Board designed for Advantech's RISC Qseven module. It is compatible with the ROM-7420 Qseven module and provides a thorough environmentfor RISC module board evaluation. It supports wide range temperatures and 12V power input through AC/DC power adapter.
-
product
PICMG Single Board Computers
ADLINK's industrial Slot Single Board Computers (SBCs) and backplanes follow PCI Industrial Computer Manufacturers Group (PICMG) 1.0 and 1.3 standards, with card-on-backplane architecture delivering faster Mean Time to Repair (MTTR) over conventional motherboard designs, flexible backplane configurations, functional with a broad range of off-the-shelf peripheral cards. ADLINK’s wide range of PICMG 1.0/1.3 CPU board-compatible backplanes are fully co-functional with ADLINK systems, for flexible configuration and expandability in industrial applications.
-
product
PICMG® 1.3 Full-Size 6th generation Intel® Core™ i7/i5/i3 LGA1151 Processor-based SHB (Code name: Skylake)
NuPRO-E43
The ADLINK PICMG 1.3 SHB, the NuPRO-E43, supporting the 6th Gen IntelR Core i7/i5/i3 processor and equipped with the IntelR Q170 Express chipset. The NuPRO-E43 supports high-speed transfer interfaces such as PCIe3.0, USB 3.0, and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2133 MHz memory up to 32 GB.
-
product
Board
Arduino Uno Rev3
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
-
product
Breakout Boards
Micro D
Micro D Breakout Boards are also open designs providing signal access for the popular MicroD series of connectors. Breakout boards incorporate one male and one female connectors.Micro D Type: 9, 15, 21, 25, 31, 37, 51 and 100 positions
-
product
Boards
MIL-STD-1553
The MIL-STD-1553 multi function interface cards are compatible with all common variations of MIL-STD-1553 and provides a wide range of features normally found only on full size testers. The card can operate simultaneously as a Bus Controller (BC) and/or multiple (up to 32) Remote Terminals (RT), or as a Triggerable Bus Monitor. The card supports error injection and detection.
-
product
Server Boards
Advantech Serverboards support Intel Xeon Processor, DDR4, IPMI 2.0 with iKVM and Quad LANs features. Our Serverboard enables various system configurations and diverse options of modules to help fulfill various field application.
-
product
DUT Boards
RTI designs and manufactures DUT boards for many types of special purpose test equipment including: ESD test systems, special purpose functional testers, automated curve trace equipment, as well as standard semiconductor test equipment. All designs are performed in-house using PCB design software (Mentor PADS, CAM350) and 3D mechanical design software (Solid Edge) if required. PCB fabrication is sub-contracted to one of our long-time fabrication partners.
-
product
Multi-Functional Board
PCI - HARPOON
PCI-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCI-Harpoon is to simulate - act as if the PCI-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCI-Harpoon can provide status and direct software control of the system.
-
product
Board
STEMlab 125-14
It has two 125Msps 14-bit inputs and two 14-bit outputs, Xilinx Zynq 7010 FPGA and offers remote access, with an online app user interface accessible through Ethernet or Wi-Fi.
