-
Product
Avionics Communications Bus
ARINC-664 p7 (AFDX)
-
ARINC-664 p7 (AFDX) is an avionics communications bus that has been mandated by both Boeing and Airbus for use in new civilian avionics designs. The following tutorial provides a brief introduction to the central features of AFDX.
-
Product
HART Communicators
-
Meriam's flagship products, the MFC5150 HART Communicator which enables direct communication from any HART transmitter wirelessly and the MFT 4010 Modular Calibrator, which delivers the versatility of a calibrator and the convenience of HART Communications afford Meriam the advantage of providing products with the highest level of innovation for commissioning, configuring and maintaining devices to allow for efficient process operations. These smart devices were designed to optimize process automation via HART Communication by offering analytic support for flow, level, pressure, temperature and valve applications.
-
Product
One Wire Communication Board
MS 1727
-
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Product
2.92mm to ProLink Adapter with Probe Power and Communication Pass Through
L2.92A-PLINK
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PLINK adapter converts the 2.92mm interface to a ProLink interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi such as Dx10/Dx20/Dx00A-AT 4-6 GHz differential probes and DH Series 8 to 20 GHz differential probes using the ProLink oscilloscope probe connection. Full probe power and control is provided through a built-in LEMO interface.
-
Product
Satellite Communications
-
Satellite telemetry offers a communication alternative for remote locations where phone lines or radio frequency systems are an impractical choice. Using satellite telemetry, communication is achieved by interfacing a data logger to a satellite transmitter, which in turn transmits the data from the field site to a receiving station.
-
Product
V4 Marine Communications System - V4 NAVTEX Test System
-
The ICS Electronics Limited V4 NAVTEX Test system may be used for type approval, general performance testing and production testing of NAVTEX receivers.
-
Product
Integrated USBL Acoustic Tracking and Communication Systems
-
The TrackLink systems are the world's best selling USBL acoustic tracking systems with fully integrated high speed acoustic communication capability. Capitalizing on its benchmark Broadband Acoustic Spread Spectrum (BASS) technologies, LinkQuest provides the end users with solutions for underwater tracking and communication at sharply reduced cost and increased robustness. An extensive line of models are available to suit the users' specification and budget constraint.
-
Product
ProLink to 2.92mm ProAxial Adapter with Probe Power and Communication Pass Through
LPA-2.92-PX-KIT
-
ProLink to 2.92mm ProAxial Adapter with Probe Power and Communication Pass Through.
-
Product
Radio Communications & Signal Analysis
-
Finding the appropriate solution for your wireless communications needs is critical. At Morcom you will always be given a professional opinion and competitive pricing. We only carry the best brands and our proposals are always reviewed and approved by a professional communications engineer. So, whether your needs are for two-way radios, broadband wireless systems, or in-building wireless Morcom will give you the best solutions.
-
Product
Communications Module
CC02A
-
The CC02A Communications Card facilitates serial communications between each module in a Zero Two Series Flame and Gas Detection System and an external host computer, which allows fast access to operational and setup data registers. It supports a Burst Read feature that returns all registers of a module in a single transmission.
-
Product
Serial Communication Products
-
Many types of external computer equipment have a serial ports to communicate with host PCs. ACCES I/O has Communication Cards for all of the popular protocols you may find on this type of equipment (RS-232, RS-422 and RS-485), ranging from a single port to eight ports on a single card. There are also optically isolated versions of some of these cards to ensure effective data transmission on long communication lines, even in electrically noisy environments. Having optical isolation is like having data insurance.
-
Product
Microwave Communication Trainer
-
We are instrumental in offering quality range ofMicrowave Products that finds application in satellite communication, broadcast and educational centers. Our range includes microwave test bench, critical microwave band & joint and MIC trainer. These products are known for optimum performance and high efficiency.
-
Product
Communication Protocol Analyzer
LE-150PR
-
LE-150PR is a lightweight communication protocol analyzer has a Data Logger function to record data in the SD card for long hours. It is an entry model designed for Asynch communication. While succeeding all the excellent cost-performance of LE-150PS, LE-150PR can be connected by Wi-Fi (available only in Japan, USA, Canada, and EU).
-
Product
Coherent Optical Communications
-
Generate high-bandwidth, complex modulation format optical signals with our high-performance coherent optical communications solutions.
-
Product
FMC for Data Communication Dual 1 Gigabit Ethernet FMC
FMC431
-
Sundance Multiprocessor Technology Ltd.
The FMC431 is a dual 1 Gigabit Ethernet FPGA Mezzanine Card with two RJ45 connectors available on the front panel. Compliant with the VITA 57.1 standard the FMC431 offers a High Pin Count connector but is compatible with FPGA carrier cards with Low Pin Count connectors. The Ethernet interface (1000BASE-T) is either implemented using RGMII (Low Pin Count compatible) or SGMII (High Pin Count compatible). The FMC431 also offers the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC431, thus offering users with the ability to build a complete data acquisition, waveform generation and communication solution while using a single FMC site on an FPGA carrier card. The FMC431 is an ideal solution to bring Ethernet connectivity to an FPGA based system and ensure reliable external communication.
-
Product
Communication Protocol Test Harness
-
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
Product
Scienlab Measurement And Control Module
SL1063B
Communications Module
The Measurement & Control Module SL1063B is a rack-mount measuring and control module for measuring and switching of digital signals with 16 digital in-/output channels. The module can be used either as a stand-alone device or as extension for a Scienlab Battery Test System.
-
Product
4 Serial Communication Channels, Multi-Mode Programmable, Isolated
SC2
-
Module SC2 supports intelligent, full duplex, independent, multi-channels that can be individually software-configured for either RS-232C, RS-422, RS-485, RS-423 (w/data and/or clk bit inversion for MIL-STD-188C unbalanced interface support), or synchronous or asynchronous communications.
-
Product
AC/DC CAT IV 600 A TRMS Navigator Clamp Meter
ACDC-52NAV
-
The ACDC-52NAV clamp-on power meter is the ideal choice for jobs that require AC/DC current measurements to 600 A, AC/DC voltage to 1000 V and wide jaws to accommodate large conductors.
-
Product
MXI-Express Cable with Communication Levels up to Gen 3 x8
781042-100
MXI Express
MXI-Express Cable, Gen 1 x4, Fiber Optic, 100m
-
Product
1000 A AC/DC Navigator Clamp Meter with Temperature
Amprobe ACDC-54NAV
-
The ACDC-54NAV clamp-on power meter offers AC/DC current measurements to 1000 A, AC/DC voltage to 1000 V, temperature capabilities, and wide jaws to handle large conductors up to 1.6″ (40 mm) for high voltage industrial environments.
-
Product
16-Port RS232 Async Serial Communications Adapter PMC
2238
-
The Technobox 16-Port Async Communication adapter provides sixteen 16550-based UARTs using RS232 signaling levels.
-
Product
CANBus Communication
PEX-CAN200i-T
-
PEX-CAN200i can represents an economic solution of an active CAN board with express PCI bus. It has 2 independent CAN bus communication ports with 5-pin screw terminal connector or 9-pin D-sub connector, and has the ability to cover a wide range of CAN applications. Besides, PEX-CAN200i uses the new CAN controller Phillips SJA1000T and transceiver 82C250, which provide bus arbitration, error detection with auto correction and re-transmission function.
-
Product
2 Channels, MIL-STD-1553/1760 Communications Interface
FTK
-
Based on the MIL-STD-1553 signal and interface backbone, MIL-STD-1760 defines a standardized electrical interface to address additional aircraft weapons stores management and as such, includes some special requirements. The FTK module meets the operational requirements within the general specifications of MIL-STD-1760 as applied to an integrated I/O function module, and include special designed holt transceivers to ensure signal parameter operation and integrity.
-
Product
Data Communications
-
Renesas' MIL-STD-883-compliant CMOS Manchester Encoder-Decoder (MED) is a high-speed, low power device manufactured using self-aligned silicon gate technology. The device is intended for use in serial data communication, and can be operated in either of two modes, a converter mode or repeater mode. This device is qualified to QML Class Q military standards.
-
Product
Wi-Fi Communications
-
Campbell Scientific offers complete Wi-Fi connectivity solutions for your data acquisition needs. Data loggers are available with integrated Wi-Fi modules, as well as stand-alone Wi-Fi devices.
-
Product
Community Noise Prediction Software, Version 2
SPM9613
-
A low-cost computer program for analyzing community noise and sound propagation emitted from a variety of noise sources. The engineering software is based on the ISO 9613 parts 1 and 2 standards. SPM9613 provides calculations at specific field points (listeners) and predictions of A- and C-weighted sound level contours as well.
-
Product
Quad Channel Serial Communication Controller
CPCI-SCC04-ISO
Controller
The CPCI-SCC04-ISO Module is a quad Channel serial Communication controller with 2K Fifo per Line. The CPCI-SCC04-ISO module is based on 4 enhanced Z85233, with larger FIFOs and several SDLC improvements from Zilog. This module provides four synchronous ports up to 230 kbaud synchronous ports and up to Data Rates up to 5.0 Mbit/Sec full-duplex channels, with an independent baud rate generator for each channel.
-
Product
Optical Communication Analysis
-
In lab and manufacturing environments, R&D engineers require scalable and optimized test solutions to enable them to properly characterize new advanced modulation scheme signals for next-generation, ultra-high-speed telecom networks. Through EXFO’s optical communication analyzers, R&D engineers and manufacturing operations involved in the development or production of transmitters or systems based on new high-speed technology will find the right tools for their advanced technology needs.
-
Product
12 Channels, ARINC 429/575 Communications
AR1
-
The AR1 provides an ARINC 429/575 communications interface with 12 channels. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer. Each channel is programmable as either Tx or Rx.
