Sensor Amplifiers
-
Product
RF Amplifiers
-
UST specializes in the testing, repair and refurbishment of all types of RF amplifiers (broadband and narrowband), microwave amplifiers and millimeter-wave amplifiers: solid state, thin film, traveling wave tube (TWT), low noise RF amplifiers, intermediate power RF amplifiers, limiting RF amplifiers, doubler RF amplifiers, driver RF amplifiers, variable gain RF amplifiers, and active frequency multipliers.
-
Product
Video, Audio & Time Code Distribution Amplifiers
-
ESE has an extensive line of Distribution Amplifiers for both Video, Audio and Time Code. Our popular ES-207A is a small 1 x 4 video DA which can be tucked away anywhere. Other models have 1 x 8 and 1 x 12 capability. Rack-mount, PC card and "black box" configurations are available.
-
Product
SparkFun Current Sensor Breakout
INA169
-
The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a small current based on the measured voltage drop. If you place a resistor from the output of the INA169 to ground, you can measure the voltage at the output.
-
Product
Amplifiers
-
Alnair Laboratories Corporation
A specially designed Erbium-doped fiber amplifier which offers a superior optical amplication performance with a very high gain factor and a minimal added noise. A near quantum limited noise figure of typically 3.8dB, and a small-signal optical gain of over 50dB is achievable with input signal as low as -50 dBm reflecting the impact of the specialty fiber and composite amplifier design, making it an indispensable amplifier for weak optical signals.
-
Product
Variable Reluctance Pressure Sensor with All-Welded Construction
DP10
-
The DP10 Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full scale output of 30 mV per volt at 3kHz. The unit operates with carrier system including the Validyne CD15 since wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator.
-
Product
GMC Oxygen Sensor
KS60113 - GMC
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
TMR Switch Sensor Demo Board
-
MultiDimension Technology Co.,Ltd.
Demonstration kit for MDT omnipolar and bipolar TMR switch sensors
-
Product
Amplifiers
-
Packaged and Die up to 26 GHzOver 145 MMIC Surface Mount and Die modelsConectorized models, power output to 100WHigh dynamic range, low noiseLow-cost, custom solutions available!
-
Product
Shear Beam Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges
-
Product
Fluid Level Sensor
-
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
SparkFun Environmental Sensor
BME688 (Qwiic)
-
The SparkFun BME688 Environmental Sensor is a breakout that combines a gas scanning sensor with temperature, humidity, and barometric pressure sensing for a complete environmental sensor in a single package. The gas sensor on the BME688 can detect a wide variety of volatile organic compounds (VOCs), volatile sulfur compounds (VSCs), and other gases such as carbon monoxide and hydrogen in the part per billion (ppb) range. Combine that with precise temperature, humidity, and barometric pressure and the BME688 can work as a completely standalone environmental sensor all in a 1in. x 1in. breakout!
-
Product
Amplifier Modules Broadband
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Reference DAC, Pre And Headphone Amplifier
CALLIA
-
Designed and manufactured in the United Kingdom, CALLIA embodies the Prism Sound uncompromising approach to audio resulting in the most accurate and detailed DAC available.
-
Product
Oxygen Logger Sensor
NUL-205
-
This sensor can be used to make measurements of the level of free oxygen in air or dissolved oxygen in water. The free oxygen in air mode is used to measure changes in oxygen levels during combustion or in reactions that produce oxygen (hydrogen peroxide decomposition). The dissolved and free oxygen modes are very useful in the study of photosynthesis.
-
Product
DC current Sensors
CTH
-
The CTH sensors convert dc current to an isolated voltage output, the CTHR sensors convert ac current to a dc output signal proportional to the Arms. All popular process control voltage and current loop outputs are available. Through hole or split core options mean that connection is non-intrusive and straightforward. The available input range of the CTH sensors is any value from 5A to 6000Adc.
-
Product
Buoyancy Level Sensors and Switches
-
ABB offers a complete line of buoyancy point level switches for just about any chemical, petroleum or general process application. This family of products include horizontal floats, vertical floats, and displacer switches of all kinds. ABB's simple and reliable design offers great flexibility with custom insertion lengths, temperature ratings to 1000ºF/ 38ºC. Pressure ratings to 5000 psig/345 bar, and a wide selection of alloys. The ABB buoyancy switches are the highest quality and cost efficient solution to industrial liquid level point sensing.
-
-
Product
Thermopile Detectors and Sensors
-
Our Thermopile Detectors are typically Thermopiles with integrated Thermistor providing analog output in various packages. Special designs include built-in lenses or reflectors to enhance sensing performance, Isothermal constructions, or Dual narrow-band windows. Our latest Thermopile Sensors include specially designed electronic circuitry to provide calibration, digital output, and functionality. With the DigiPile, Excelitas offers a unique design for measurement applications. With its digital output, this device does not require any low noise amplification. The CaliPile family provides integrated features that enable measurement, as well as presence detection applications.
-
Product
AC Current Sensor
RCTi and RCTi 3ph
-
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
-
-
Product
CMOS Image Sensor
CIS
-
CMOS Image Sensors (CIS) allow multiple camera functions in mobile devices, automobiles and security systems. Nidec SV Probe provides both standard and advanced versions of our CIS cards employing a wide variety of materials ensuring a durable cost-saving solution that can meet the fine pitch and multi-dut challenges of these devices. Other features and benefits include: • Proprietary AC™ Alloy Probes • Reduced Damage Under the Pad • High Frequency Capability • Better Alignment StabilityOur advanced CIS card, the Multiplexer™, is offered specifically for high density and high parallel applications. The Multiplexer™ is built with cantilever needles held into place on one side and shorter AC™ probes on the other which leads to a more stable electrical characterization over other CIS probe card options.Contact your Nidec SV Probe Representative so we can help you find the right CIS product for your testing needs.
-
-
Product
Force Sensors
-
TE Connectivity (TE) designs and manufactures force sensors for applications that require high performance or unique packaging, including electro-mechanical flight control, test and measurement and ultra-low cost OEM load cells for medium to high volumes. Based on our proprietary piezoresistive silicon strain gage (Microfused) technology, our sensors combine durability and long-term stability in extremely low cost packages.
-
Product
Fiber Optic Pressure Sensors
-
Opsens Solutions optical pressure sensor delivers reliable results in harsh environment. Opsens Solutions OPP series fiber optic pressure transducers are designed to provide accurate pressure measurement in the most adverse conditions. Its small size and EMI/RFI/MRI immunity makes it the ideal sensor for industrial applications.
-
Product
Switched Limiting Amplifier With Detected Output
-
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
Product
Sensors
Chromatic Focus Probe
-
Measurement of highly reflective, absorbent and transparent materialsMeasuring results are independent of the surface propertiesEspecially suitable for fast and precise measurements on reflective surfaces, lenses, prisms and other optical devicesFlexible probe configurations for highly customized applications
-
Product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
-
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
Karman Vortex Flow Sensor For Water Flurex
WFK3000
-
Karman vortex detection type flow sensor for water. Compact and simple design suitable for mounting on equipment.
