Mains
chief conduit of electricity, gas or water distribution.
-
Product
Pinhole & Porosity
-
Premature corrosion of a substrate is usually due to a coating failure. A major cause is the presence of flaws in the finished coating. Collectively referred to as porosity, the main types of flaws are:
-
Product
2nd Generation PCI Multi-function Decommutator
LS-50-D
-
The Lumistar LS-50-D PCI Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCI card slot. The multi-function decom and simulator are implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profile daughterboard. CVSD voice decoding, h.261 video decoding, and IRIG Chapter 8 decoding are achieved through software.
-
Product
Leak Detection System
-
Leak detection system (LDS) is a state-of-the-art software and hardware suite intended for leak detection in long-distance and oil products pipelines, calculation of leak location and evaluation of its intensity in constant full-time mode. The system allows to detect leaks in stationary and non-stationary pumping modes without gravity mains as well as in suspended pumping mode.
-
Product
Portable Appliance Tester
PrimeTest 50
-
The PrimeTest 50 portable appliance tester is battery powered and handheld to allow for fast and efficient testing with clear PASS/FAIL indication. A simple range of tests are selected at the push of a button to test earthed equipment, double insulated equipment, mains cords and leads.
-
Product
Environmental Chamber
REXMED REC-280
-
MOD. REC-280, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,140 Watts, 10,700 BTU/hr, 2,702 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
PXI Single 8x4 1-Pole 10A Power Matrix
40-551-001
Matrix Switch Module
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, also available with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
Product
Hybrid Power Divider, 2 GHz to 26.5 GHz
87304C
-
The Keysight 87304C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.
-
Product
Force Tensiometer
K20
-
Our Force Tensiometer – K20 is a robust, semi-automatic instrument for the precise measurement of surface tension and interfacial tension. Using the ring and plate method as the main tensiometric methods, it produces reliable measurements for the routine quality assurance of your surfactant solutions and interfacial processes.
-
Product
PWM TO VOLTAGE SIGNAL CONVERTER
RCPWM2V
-
The RCPWM2V is a device that converts a standard hobby RC signal (1-2ms pulse) into a proportional analog voltage (0-5V). In many electronics applications the main processor is constantly busy and does not have the ability to address the time-sensitive PWM signal from an RC receiver immediately. This results in signal distortion or a sluggish response due to the extra filtering required. The RCPWM2V provides a simple solution by converting the signal into an analog signal. The main processor can then read the signal whenever it has time.
-
Product
Compact PCI Multi-function Decommutator
LS-50-cP
-
The Lumistar LS-50-cP 3U Compact PCI Multi-function PCM Decommutator offers the greatest flexibility in the industry by incorporating up to 10 functions typically encountered in flight test applications in a single 3U Compact-PCI card slot. Five functions are achieved on the main board (PCM Simulator which can also operate as a BERT, PCM Decommutator, IRIG Time CodeReader, IRIG Time Code Generator, and the same 5 functions can be achieved on the LS-55-DB Multi-Function Decom Daughterboard. CVSD Voice Decoding and h.261 Video Decoding are achieved through software.
-
Product
Test Bench
BERTA
-
OPAL-RT’s BERTA test bench is a safe, reliable and portable test bench for speed governors, turbines, voltage regulators (AVR) and power system stabilizers (PSS). Equipped with a high-performance real-time simulator programmed with world-renowned RT-LAB software, the BERTA Test bench enables users to easily and comprehensively test real generating units in the power plant, synchronized and transmitting power to the main grid and/or on real controllers connected to a virtual generating unit in laboratory.
-
Product
Electrical
-
American Environments Co., Inc.
This testing includes the simulation of conditions or events that are associated with a device's input power leads (Mains).
-
Product
Four Outputs Optical Node
9940
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Optical node is the earliest manufacturing that adopts AUGAT aluminum die-casting to make 4 ports optical communication platform. The platform is gradable and has become the main device that widen HFC subscribers access network. It is widely used in FTTB, FTTC. Its RF output is driven by one power-doubling module. It can be installed with 2 receivers, 4 transmitters and 2 power supplies (main and back-up ), which can improve the system redundancy.
-
Product
PD Monitoring systems
TECHIMP PD Hub™
-
Techimp’s Partial Discharge (PD) Monitoring systems usually consists of a Central Unit and distributed Data Acquisition Units – the PD Hub™ - able to acquire and process the PD signals locally detected through PD sensors installed on each of main electrical assets (generator, transformer, HV cables and GIS).
-
Product
Digital Circuit Breaker Analyzer
CT-8000 S3
-
The CT-8000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-8000 S3 is available with 3 (part number 9103-UC) or 6 contact timing channels (part number 9104-UC). The CT-8000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Also, an outstanding feature of the CT-8000 S3 is the ability to perform dynamic resistance tests on circuit breaker contacts.
-
Product
Three-phase Fully Automatic Test System
TS33
-
Calmet Smart Calibration Devices
The Calmet TS33 portable test system consists of a three-phase reference meter of accuracy class 0.02%, 0.04% or 0.1% and an integrated three-phase current and voltage source up to 3x120A/600V. The TS33 is designed for analysis of complete metering installations and local mains conditions.
-
Product
Power Supply Units
-
converts mains AC to low-voltage regulated DC power for the internal components of a computer. Modern personal computers universally use switched-mode power supplies.
-
Product
Insulation Tester
Megohmmeter, 5kV
-
*Auto Calibration on Start-up*Onboard Battery Charger*Mains Power: 90-260Vac, 45-65 Hz*Hazardous Voltage Warning Icon > 70 volts*Test: Insulation, Voltage & Frequency
-
Product
Enlarge Environmental Chamber
REXMED REC-480
-
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Ultrasonic Probes And Cables
-
The cable connects the main body of ultrasound diagnostic equipment and the probe used for echographic investigation.
-
Product
Hall Effect Measurement system
HMS-3300
-
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
Product
C-Mic Testing System
BK3010
-
The BaKo BK3010 is our main C-Mic tester. It's small enough to carry under your arm and with a test time of under 0.5 seconds, it tests as fast as you can connect a microphone. Setting up the specifications is so easy and intuitive, we based the BK3012 D-Mic Tester on it. It is also the model for our BK9010B Fully Automatic C-mic Tester.
-
Product
High Precision TMAH Concentration Monitor
HE-960H-TM-S
-
Accurately measures the concentration of TMAH (Tetra Methyl Ammonium Hydroxide), which is the main component of the photoresist developer solutions in semiconductor manufacturing. Repeatability: within +/- 0.003%. Measurement range : 0 - 3 %. Have the chemical resistant carbon sensor.
-
Product
Colorimeter
Model CA-600
-
Teledyne Analytical Instruments
The CA600 is an online sequential sampling analyzer, using colorimetric methods. The analyzer can be configured to most laboratory colorimetric tests in individual processes.The CA600 Analyzers are easy to start up and use, simply connect the sample, waste and reagent lines and then power up the factory calibrated analyzer. Wall mount hardware is standard but an optional bench-top stand with reagent holder is also available. Accessing information for customizing an analysis routine is easily accomplished with the simple, user friendly menu structure and touch screen interface.The analyzer has two separated enclosures with two lockable doors. The top enclosure, called the electrical enclosure, includes the main power supply, the controller PCB assembly and the touchscreen interface. The bottom enclosure, called the liquids enclosure, includes all the components involved in the sample and reagent flow, mixing and reaction stages (sampling pump, reagent micro pumps and colorimetric reaction cell). Numerous analysis configurations can be programmed, depending on the accessories and the number of micro-pumps mounted in the liquid enclosure.
-
Product
Socket Tester with RCD Tripping
-
Shanghai Beha Electronics Co., Ltd.
*Mains wiring polarity check.*ELCB/RCD testing.*Measuring ear for line current.*Measuring ear for leakage current.*Helps calculate insulation resistance.*Helps calculate power consumption.*Helps fault finding of standing earth fault.*Fused main adapter.*Appliance testing (with the ad of a clamp meter).
-
Product
Through Hole Type AC Current Sensor
CTF-600B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A～600A.
-
Product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
Matrix Switch Module
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
Product
Flex Modules
-
One of the main advantages of our range of Flex Modules is the ability to “mix and match” test modules to meet your specification. Not only can you have the system delivered with all the necessary resources, but as your requirements grow we can supply further modules that can be retro fitted to the system. The number of modules available is extensive and covers a wide range of applications. Whether your need is for RF, High Voltage, Digital, or a combination of all of these, we have a solution. Check out the various sections below and get in touch to discuss your requirements.
-
Product
Earth Resistance & Resistivity Meter (for 50Hz mains)
MRU-120
-
* earth resistance measurment with 3-pole,4-pole method, * earth resistance measurement without disconnecting measured earths (using clamp), * continuity of equipotential bondings and protecting conductors * two clamps earth resistance measurement without auxiliary test probs, * earth resistivity measurement,
-
Product
Electronic Equipment Testing System
-
The task set forth the need to create a special universal software core, the main tasks of which are the provision of measurement and control processes, as well as the interaction of software components intended for collection, visualization, mathematical processing and documenting of data. For each stand, specific program modules were additionally developed according to test methods specific products. The overall modular architecture of the system makes it easy to supplement and correct test algorithms.
